User`s manual
Table Of Contents
- 75KV_FULLNBv10.pdf
- C O N T E N T
- Chapter 1 INTRODUCTION
- 1-1 ITEM LIST CHECKUP
- 1-2 processor
- 1-3 chipset
- 1-4 memory
- 1-5 bios
- 1-6 multi-i/o function
- 1-7 form factor
- 1-8 acﾕ97 codec function
- 1-9 MISCELLANOUS
- 1-10.1 motherboard layout --- 75kv
- 1-10.2 motherboard layout --- 75kv-X
- 1-11 CHIPSET DIAGRAM
- Chapter 2 HARDWARE SETUP
- 2-1 CPU INSTALLATION
- 2-2 amd socket A (SOCKET 462) PROCESSOR
- 2-3 CPU FREQUENCY
- 2-4 jumper definitions
- 2-5 connectors
- 2-5.1 J3 AND J4
- 2-5.2 CHASSIS PANEL CONNECTOR
- 2-5.3 ATX POWER SUPPLY CONNECTOR
- 2-5.4 SECOND USB CONNECTOR
- 2-5.5 PS/2 MOUSE AND PS/2 KEYBOARD
- 2-5.6 IRQ DESCRIPTION
- 2-6 VOICE DIAGNOSIS TECHNOLOGY FOR 75KV-X
- Chapter 3 SOFTWARE SETUP
- 3-1 ABOUT SUPPORT CD
- 3-2 HARDWARE MONITOR INSTALLATION
- 3-3 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER)
- 3-4 ACﾕ97 AUDIO CODEC INSTALLATION
- Chapter 4 BIOS Setup
- 4-1 INTRODUCE THE BIOS
- 4-2 WHAT IS BIOS SETUP
- 4-3 HOW TO RUN BIOS SETUP
- 4-4 WHAT IS CMOS
- 4-5 WHAT IS POST
- 4-6 BIOS UPGRADE
- 4-6.1 BEFORE UPGRADE BIOS
- 4-6.2 UPGRADE PROCESS
- 4-7 CMOS SETUP UTILITY
- 4-8 STANDARD CMOS SETUP
- 4-9 ADVANCED BIOS FEATURES
- 4-10 ADVANCED CHIPSET FEATURES
- 4-11 INTEGRATED PERIPHERALS
- 4-12 POWER MANAGEMENT SETUP
- 4-13 PNP / PCI CONFIGURATION
- 4-14 PC HEALTH STATUS
- 4-15 FREQUENCY/VOLTAGE CONTROL
- 4-16 LOAD FAIL-SAFE DEFAULTS
- 4-17 LOAD OPTIMIZED DEFAULTS
- 4-18 SET SUPERVISOR / USER PASSWORD
- 4-19 SAVE & EXIT SETUP
- 4-20 EXIT WITHOUT SAVING
- C O N T E N T
18
MAGIC-PRO MP-7VIP-A
ATX POWER SWITCH
PIN 12 ATX POWER SWITCH
PIN 13 GND
DESCRIPTION
The system power is controlled by a momentary
switch connected to this lead.
Pressing the button once will switch the system
between ON and SOFT OFF.
Pushing the switch while in the ON mode for more
4 seconds will turn the system off.
The system power LED shows the status of the
system's power.
123456789101112 13 14 15
J4
J3
SMI CONNECTOR
PIN 14 SMI(System Managment Interrupt) SIGNAL
PIN 15 GND
DESCRIPTION
This allows user to manually place the system into a
suspend mode or "Green" mode, where system
activity is decreased to save electricity and prolong
the life of certain components when the system is
not in use. This 2-oin connector connects to the
case-mounted suspend switch. If you do not have a
switch for the connector, you may use the "Turbo
Switch".
SMI is activated when it detects a short to open
moment and therefore leaving it shorted will not
cause any problems. This may require one or two
presses depending on the position of the switch.
Wake-Up can be controlled by settings in the BIOS
but the keyboard will always allow wake-up(the SMI
lead cannot wake up the system).
1234567891011121314 15
J4
J3