User`s manual
Table Of Contents
- 75KV_FULLNBv10.pdf
- C O N T E N T
- Chapter 1 INTRODUCTION
- 1-1 ITEM LIST CHECKUP
- 1-2 processor
- 1-3 chipset
- 1-4 memory
- 1-5 bios
- 1-6 multi-i/o function
- 1-7 form factor
- 1-8 acﾕ97 codec function
- 1-9 MISCELLANOUS
- 1-10.1 motherboard layout --- 75kv
- 1-10.2 motherboard layout --- 75kv-X
- 1-11 CHIPSET DIAGRAM
- Chapter 2 HARDWARE SETUP
- 2-1 CPU INSTALLATION
- 2-2 amd socket A (SOCKET 462) PROCESSOR
- 2-3 CPU FREQUENCY
- 2-4 jumper definitions
- 2-5 connectors
- 2-5.1 J3 AND J4
- 2-5.2 CHASSIS PANEL CONNECTOR
- 2-5.3 ATX POWER SUPPLY CONNECTOR
- 2-5.4 SECOND USB CONNECTOR
- 2-5.5 PS/2 MOUSE AND PS/2 KEYBOARD
- 2-5.6 IRQ DESCRIPTION
- 2-6 VOICE DIAGNOSIS TECHNOLOGY FOR 75KV-X
- Chapter 3 SOFTWARE SETUP
- 3-1 ABOUT SUPPORT CD
- 3-2 HARDWARE MONITOR INSTALLATION
- 3-3 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER)
- 3-4 ACﾕ97 AUDIO CODEC INSTALLATION
- Chapter 4 BIOS Setup
- 4-1 INTRODUCE THE BIOS
- 4-2 WHAT IS BIOS SETUP
- 4-3 HOW TO RUN BIOS SETUP
- 4-4 WHAT IS CMOS
- 4-5 WHAT IS POST
- 4-6 BIOS UPGRADE
- 4-6.1 BEFORE UPGRADE BIOS
- 4-6.2 UPGRADE PROCESS
- 4-7 CMOS SETUP UTILITY
- 4-8 STANDARD CMOS SETUP
- 4-9 ADVANCED BIOS FEATURES
- 4-10 ADVANCED CHIPSET FEATURES
- 4-11 INTEGRATED PERIPHERALS
- 4-12 POWER MANAGEMENT SETUP
- 4-13 PNP / PCI CONFIGURATION
- 4-14 PC HEALTH STATUS
- 4-15 FREQUENCY/VOLTAGE CONTROL
- 4-16 LOAD FAIL-SAFE DEFAULTS
- 4-17 LOAD OPTIMIZED DEFAULTS
- 4-18 SET SUPERVISOR / USER PASSWORD
- 4-19 SAVE & EXIT SETUP
- 4-20 EXIT WITHOUT SAVING
- C O N T E N T
13
MAGIC-PRO MP-7VIP-A
2-4 JUMPER DEFINITIONS
• The figure below shows the location fo the motherboard’s jumper blocks.
CAUTION
• Do not move the jumper with the power on. Always trun off the power and
unplug the power cord from the computer before changing the jumper.
Otherwise, the motherboard could be damaged.
CPU FAN
FAN1/FAN2: ONBOARD FAN (12V)
FAN2
FAN1
SYSTEM FAN
Those connectors support processor/system/chassis cooling fan
with +12V. Those support three pin head connector. When con-
necting the wire to FAN connectors, user should give attention that
the red wire is the positive and should be connected to the +12V,
the black wire is Ground and should be connected to GND. If your
motherboard has Hardware Monitor chipset on-board, you must
use a specially designed fan with speed sensor to take advantage
of this function.
For fans with fan speed sensor, every rotation of the fan will send
out 2 pulses. System Hardware Monitor will count and report the
fan rotation speed.
NOTE 1: Always consult vendor for proper CPU cooling fan.
NOTE 2: CPU FAN supports the FAN control. You can install PC
Alert utility. This will automatically control the CPU FAN
speed according to the actual CPU temperature.
GND
+12V
SENSOR
Redirect USB port 3 to USB 2
connector (default)
JP1/JP2: USB PORT SELECT
1 3
1 3
JP1
JP2
1 3
1 3
JP1
JP2
Redirect USB port 3 to AGP