MP-7VIP Motherboard User’s Manual Product Name: MP-7VIP Manual Revision: English, 1.
Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: w This device may not cause harmful interference w This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
MAGIC-PRO MP-7VIP CONTENT Chapter 1: Introduction .......................... 4 1-1 CPU .................................................................................... 4 1-2 CHIPSET ............................................................................ 4 1-3 L1 / L2 CACHE ................................................................... 4 1-4 MAIN MEMORY .................................................................. 5 1-5 BIOS ................................................................
MAGIC-PRO MP-7VIP 3-5: WHAT IS POST ............................................................... 20 3-6 STANDARD CMOS FEATURES ...................................... 22 3-7 ADVANCED BIOS FEATURES SETUP ........................... 25 3-8 ADVANCED CHIPSET FEATURES ................................. 30 3-9 INTEGRATED PERIPHERALS ........................................ 34 3-10 POWER MANAGEMENT SETUP .................................. 39 3-11 PnP/PCI CONFIGURATION SETUP ..............................
MAGIC-PRO MP-7VIP Chapter 1: Introduction 1-1 CPU Supports AMD Althon Slot-A 550/ 600/ 650/ 700/ 750/ 800MHz CPUs. Supports CPU voltage Auto-Detect circuit. 1-2 CHIPSET VIA KX133 chipset includes VT8371 system controller (North Bridge) and VT82C686A PCI to ISA bridge (South Bridge). Supports 32-bit PCI and 32-bit AGP interfaces.
MAGIC-PRO MP-7VIP 1-4 MAIN MEMORY Supports PC100 and PC133 MHz SDRAM, VCM SDRAM, and ESDRAM memory up to 3 DIMMs. Different DRAM timing for each bank. Supports mixed 1M/2M/4M/8M/16M/32MxN DRAMs. Supports up to 1.5GB memory space (256MB DRAM technology). Supports 3pcs 168pin DIMM sockets ( 64-bit data width and 3.3V DRAM interface with 5V-tolerant inputs). Two-bank interleaving for 16Mbit SDRAM support. Two-bank and four bank interleaving for 64Mbit SDRAM support.
MAGIC-PRO MP-7VIP 1-8 MISCELLANOUS ATX form factor. Mainboard size: 19mm X 30.5mm. Provides 5x PCI slots, 1x ISA slot, 1x AMR slot, 1x AGP slot and 3x DIMM sockets. AGP 2.0 interface with 1x 2x / 4x data transfer and 2x / 4x fast write capability. AGP Universal Connector supports via dual mode buffers. Supports SCSI, CD-ROM, ZIP, LS-120 boot up function. Supports Wake On LAN (WOL) boot up function. Supports keyboard power on function. Supports BIOS Writing Protection.
MAGIC-PRO MP-7VIP 1-9 MAINBOARD LAYOUT 1 SW1 ON DIP 1 2 3 4 ZD1 SLOT A AMR IDE2 IDE1 DIMM1 DIMM2 DIMM3 4x AGP 4 CD_IN1 CD_IN2 4 JP2 1 Clock Generator VIA VT8371 GAME/MIDI PORT LINE OUT LINE IN MIC 1 100MHz CPU Clock.
MAGIC-PRO MP-7VIP CFWDRST PROCRDY CONNECT 1-10 MAINBOARD CHIPSETS DIAGRAM GCLK 3D Graphics Controller AGP Bus GCKRUN# PCKRUN# PCLK PCI Bus BIOS ROM ATA 33 / 66 USB Ports 0 - 3 AC97 Audio Codec Slot-A (AMD K7) Host CPU Address Out SYSCLK, SYSCLK# INTR, NMI, SMI#, STPCLK#, IGNNE#, FERR#, A20M#, PWROK, INIT#, RESET# Data In CKE Memory Bus KX133 VT8371 North Bridge 516 BGA MCLK PCLK SUSCLK, SUSST1# VT82C 686A Super South ISA Bus RTC Crystal Clock Buffer HCLK CPUSTP# PCISTP# South Bridge
MAGIC-PRO MP-7VIP Chapter 2: Hardware Setup 2-1 CPU FSB SELECT SW1 ON FSB DIP 66MHz 1 2 ON 3 4 DIP 83MHz 1 2 ON 3 4 DIP 100MHz (default) 1 2 ON 3 4 DIP 110MHz 1 2 ON 3 4 DIP 115MHz 1 2 ON 3 4 DIP 124MHz 1 2 ON 3 4 DIP 129MHz 1 2 ON 3 4 DIP 133MHz 1 2 3 4 NOTE: Due to the Bus Ratio is internal inside the Athlon CPU, so that there is no any external jumper for user to set the Bus Ratio value.
MAGIC-PRO MP-7VIP WATCH OUT !!! 1. Please refer to your processor installation or other documentation attached with your CPU for detailed installing instruction. 2. Installing a heat sink and cooling fan is necessary for proper heat dissipation from your CPU. Uncorrected installation may result in overheating and damage of your CPU. 3. Before changing the setting of CPU Vcore from BIOS program, user SHOULD make sure of correct specification both of CPU CLOCK and RATIO.
MAGIC-PRO MP-7VIP 2-2 JUMP SETTINGS JFAN#: Onboard FAN (12V) Connector.
MAGIC-PRO MP-7VIP JP7 / JP8: USB Port Select (2) USB Port Select JP7 / JP8 Redirect USB port2 to USB2 connector (default) JP7 JP8 1 1 3 3 Redirect USB port2 to AGP JP7 JP8 1 1 3 3 JP9: Power Lost Resume This feature must work with BIOS. Please refer to the BIOS Power On After PWR-Fail sector. Power Lost Resume JP9 1 Normal (default) 3 1 Enabled 3 JBAT1: Clear CMOS Data Before you clear the CMOS data, its necessary to turn the power off first (including +5V standby power).
MAGIC-PRO MP-7VIP CD_IN1/CD_IN2: CD-ROM Audio Connector PIN # CD_IN1 CD_IN2 PIN 1 Right Channel Left Channel PIN 2 GND GND PIN 3 GND Right Channel PIN 4 Left Channel GND GAME/MIDI Port: Connect joystick or MIDI to this connector. MIC :Microphone Jack Connect to microphone device. LINE IN: Audio In Jack Connect audio line in. LINE OUT/SPEAKER OUT: Audio Out Jack Connect audio line out or speaker out.
MAGIC-PRO MP-7VIP J2 HDD LED CONNECTOR N.C. INFRARED CONNECTOR N.C. ATX POWER SWITCH SMI CONNECTOR PIN SIGNAL DESCRIPTION 1 +5V 2 HDD LED SIGNAL 3 HDD LED SIGNAL 4 +5V 5 NO CONNECTION 6 INFRARED TRANSMIT SIGNAL 7 GND 8 INFRARED RECEIVE SIGNAL 9 NO CONNECTION 10 +5V 11 NO CONNECTION 12 GND 13 ATX POWER SWITCH 14 SMI Signal 15 GND PIN1~PIN4: HDD DISK LED CONNECTOR Connect cable from the chassiss H.D.D to this connector.
MAGIC-PRO MP-7VIP J3 SPEAKER CONNECTOR RESET SWITCH N.C. POWER LED CONNECTOR N.C. SUSPEND LED PIN SIGNAL DESCRIPTION 1 SPEAKER SIGNAL 2 NO CONNECTION 3 GND 4 +5V 5 RESET SIGNAL 6 GND 7 NO CONNECTION 8 +5V 9 NO CONNECTION 10 GND 11 NO CONNECTION 12 GND 13 NO CONNECTION 14 +5V 15 SUSPEND LED PIN1~PIN4: SPEAKER CONNECTOR Connect cable from the chassiss SPEAKER to this connector. PIN5~PIN6: RESET SWITCH Connect cable from the chassiss RESET to this connector.
MAGIC-PRO MP-7VIP 2-3 CONNECTORS J2, J3: A. J2 J3 B. 15 1 15 A. C. E. G. I. K. 16 F. G. : HDD LED : POWER SWITCH : SPEAKER : POWER LED : SUSPEND LED A. B. E. F. D. 1 E. A. C. E. G. I. C. B. D. F. H. H. : : : : I. INFRARED (IR) SMI RESET SWITCH NO CONNECTION C. D. G. : PS/2 MOUSE : LPT1 PORT : PS/2 KEYBOARD : COM1 : LINE/SPK OUT : MIC H. B. D. F. H. J. I. J. : USB 0 : GAME/MIDI PORT : USB 1 : COM2 : LINE IN K.
MAGIC-PRO MP-7VIP 2-4 DRIVER INSTALLATION Onboard AC97 Audio Codec Controller Driver Installation for Windows95 / Windows98: 1. Go to CD-ROM driver, we suggest the CD-ROM title is D:\. 2. Find and run D:\MB\VIA\AUDIO\SETUP.EXE 3. Then the setup program will detect your O.S. to install relative files into your system. 4. Reboot your computer.
MAGIC-PRO MP-7VIP SuperCops III Hardware Monitor Installation Windows95 / Windows98: 1. Go to CD-ROM driver, we suggest the CD-ROM title is D:\. 2. Find and run D:\SUPERCOP\SC3\SETUP.EXE 3. Select VIA Hardware Monitor , then it will automatically install this program.
MAGIC-PRO MP-7VIP Chapter 3: BIOS Setup 3-1: INTRODUCE THE BIOS. B IOS stands for Basic Input Output System. It is sometimes call the ROM BIOS because it is stored in a Read-Only Memory (ROM) chip on the motherboard. BISO is the first program to run when you turn on your computer. It performs the followin functions: initializing and testing hardware in your computer (a process called POST, for Power On Self Test) loading and running your operating system.
MAGIC-PRO MP-7VIP 3-3: HOW TO RUN SETUP O ne way of running SETUP is to press a special function key or key combination during POST, before the operating system is loaded. During POST, the BIOS usually displays a prompt such as: Press DEL to enter SETUP 3-4: WHAT IS THE CMOS C MOS is a special kind of memory maintained by a battery after you turn your computer off. The BIOS uses CMOS to store the settings you selected in SETUP. The CMOS also maintains the intermal clock.
MAGIC-PRO MP-7VIP This VIA KX133 chipset comes with the AWARD BIOS from AWARD Software Inc. Enter the AWARD BIOS program Main Menu by: 1. Turn on or reboot the system. After a series of diagnostic checks, the following message will appear: PRESS TO ENTER SETUP 2.
MAGIC-PRO MP-7VIP 3-6 STANDARD CMOS FEATURES Standard CMOS Features allows you to record some basic system hardware configuration and set the system clock and error handling. You only need to modify the configuration values of this option when you change your system hardware configuration or the configuration stored in the CMOS memory gets lost or damaged. Run the Standard CMOS Features as follows: 1. Choose STANDARD CMOS FEATURES from the Main Menu and a screen with a list of options will appear. 2.
MAGIC-PRO MP-7VIP Date (mm:dd:yy) Time (hh:mm:ss) IDE Primary Master/ Slave IDE Secondary Master/ Slave Set the current date and time. This field records the specification for all non-SCSI Hard Disk Drives installed in your system. Refer to the following screen to know how to set Hard Disk Drive.
MAGIC-PRO MP-7VIP Drive A / B Set the field to the type(s) of Floppy Disk drive(s) installed in your system. The choice: 360KB, 5.25in. 1.2MB, 5.25in. 720KB, 3.5in. 1.44MB, 3.5in. 2.88MB, 3.5in. Video Set the field to the type of video display card installed in your system. The choice: Monochrome, Color 40x25, EGA / VGA, (default) Color 80x25 Halt On Set this warning feature for the type of errors that will cause the system to halt.
MAGIC-PRO MP-7VIP 3-7 ADVANCED BIOS FEATURES SETUP Advanced BIOS Features Setup allows you to improve your system performance or set up system features according to your preference. Run the Advanced BIOS Features Setup as follows: 1. Choose ADVANCED BIOS FEATURES SETUP from the Main Menu and a screen with a list of options will appear.
MAGIC-PRO MP-7VIP 2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys. An explanation of the keys follows: : Help gives options available for each item. + : Change BIOS screen color. : Get the previous values. These values are the values with the user started in the current session. : Load all options with the BIOS default values. : Load all options with the Setup default values.
MAGIC-PRO MP-7VIP Virus Warning Allows you to choose the virus warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. The choice: Enabled, Disabled (default) Note: Many diagnostic (or boot manager) programs which attempt to access the boot sector table can cause the above warning message.
MAGIC-PRO MP-7VIP Boot Up Floppy Seek Boot Up NumLock Status Gate A20 Option On (default): Activate the NumLock function at boot up. Off: Close the NumLock function at boot up. Fast (default): Let chipset controls GateA20. Normal: A pin in the keyboard controller controls GateA20. Typematic Rate Setting Choose Enabled or Disabled (default): Keystrokes repeat at a rate determine by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected.
MAGIC-PRO MP-7VIP C8000-CBFFF to DC0000DFFFF Shadow These options are used to shadow other expansion card ROMs. 3. Press and follow the screen instructions to save or disregard your setting.
MAGIC-PRO MP-7VIP 3-8 ADVANCED CHIPSET FEATURES Advanced Chipset Features changes the values of the chipset registers. These registers control the system options. Run the Advanced Chipset Features as follows: 1. Choose ADVANCED CHIPSET FEATURES from the Main Menu and a screen with a list of options will appear. 2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.
MAGIC-PRO MP-7VIP Bank 0/1 2/3 4/5 SDRAM Timing This item allows you to select the value in this field, depending on whether the board has paged SDRAMs . The choice: SDRAM 8ns, SDRAM 10ns (default), Normal, Fast, Turbo. SDRAM Cycle Length You can select CAS latency time in HCLKs of 2 or 3 (default). The system board designer should have set the values in this field, depending on the DRAM installed.
MAGIC-PRO MP-7VIP AGP Aperture Size Choose 4, 8, 16, 32, 64 (default), 128 or 256MB. Memory map and graphics data structures can reside in a Graphics Aperture. This area is like a linear buffer. BIOS will automatically report the starting address of this buffer to the O.S. AGP-4X Mode This item allows user to enable / disable the AGP-4x (133MHz clock) mode. The choice: Enabled, Disabled (default). AGP Driving Control The choice: Auto (default), Manual.
MAGIC-PRO MP-7VIP PCI Master 0 WS Write The choice: Enabled (default), Disabled. PCI Delay Transaction The choice: Enabled (default), Disabled. PCI #2 Access #1 Retry The choice: Enabled (default), Disabled. AGP Master 1 WS Write The choice: Enabled, Disabled (default). AGP Master 1 WS Read The choice: Enabled, Disabled (default). Memory Parity / ECC Check Enabled add a parity check to the boot-up memory tests. Select Enabled only if the system DRAM contains parity.
MAGIC-PRO MP-7VIP 3-9 INTEGRATED PERIPHERALS Integrated Peripherals option changes the values of the chipset registers. These registers control system options in the computer. Run the Integrated Peripherals as follows: 1. Choose INTEGRATED PERIPHERALS from the Main Menu and a screen with a list of options will appear. 2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.
MAGIC-PRO MP-7VIP CMOS Setup Utility - Copyright (C) 1984-2000 Award Software Integrated Peripherals OnChip IDE Channel10 OnChip IDE Channel11 IDE Prefetch Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master DMA Primary Slave DMA Secondary Master DMA Secondary Slave DMA Init Display First IDE HDD Block Mode Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART 2 Mode IR Function Duplex TX, RX inverting enable Onboard Parallel Port Onboard Para
MAGIC-PRO MP-7VIP OnChip IDE Channel 0/1 The chipset contains a PCI IDE interface with support from two IDE channels. Select Enabled to activate the first and/or the second IDE interface. Select Disabled to deactivate an interface, if you install a primary and/or second add-on IDE interface. The choice: Enabled(default), Disabled. Primary Master/Slave PIO Secondary Master/Slave PIO Choose Auto (default) or Mode 0~4. The BIOS will detect the HDD mode type automatically when you choose Auto.
MAGIC-PRO MP-7VIP IR Transmission Delay TX, RX inverting enable Enabled: Enable delay when transferring data. Disabled (default): Disable delay when transferring data. Choose Lo,Lo (default) / Lo,Hi / Hi,Hi / Hi,Lo. Onboard Paralle Port Choose the printer I/O address: 378H/IRQ7 (default), 3BCH/ IRQ7, 278H/IRQ5 or Disabled. Onboard Parallel Mode Choose Normal (default), ECP/EPP, SPP mode. The mode depends on the external device connected to this port.
MAGIC-PRO MP-7VIP SB DMA Select MPU-401 The choice: DMA0, DMA1 (default), DMA2, DMA3. The choice: Enabled, Disabled (default). MPU-401 I/O Address The choice: 330-333H (default), 300-303H, 310-313H, 320323H. Game Port (200-207H) The choice: Enabled (default), Disabled. 3. Press and follow the screen instructions to save or disregard your setting.
MAGIC-PRO MP-7VIP 3-10 POWER MANAGEMENT SETUP Power Management Setup changes the system power savings function. Run the Power Management Setup as follows: 1. Choose POWER MANAGEMENT SETUP from the Main Menu and a screen with a list of options will appear. 2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.
MAGIC-PRO MP-7VIP ACPI Function Power Management Enabled: Turn on ACPI function. Disabled (default): Turn off ACPI function. Press enter to next screen as following: The choice: User Define (default), Mix Saving or Max Saving.
MAGIC-PRO MP-7VIP ACPI Suspend Type The choice: S1(POS) (default) or S3 (STR). PM Control By APM Choose Yes (default) or No. You need to choose Yes when the operating system has the APM functions, otherwise choose No. Video Off Option The choice: Suspend -> Off (default), All Modes -> Off, Always On. Video Off Method Choose Blank Screen, DPMS Support or V/H Sync+Blank (default). You can choose either DPMS or V/H Sync+Blank when ther monitor has the Green function.
MAGIC-PRO MP-7VIP CMOS Setup Utility - Copyright (C) 1984-2000 Award Software Wake Up Events VGA LPT & COM HDD & FDD PCI Master Wake Up On LAN Modem Ring Resume RTC Alarm Resume Date (of Month) Resume Time (hh:mm:ss) IRQs Activity Monitoring OFF LPT/COM ON OFF Disabled Disabled Disabled 0 0 0 0 Press Enter Item Help Menu Level :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults 42 VGA When On of VGA, any activity from one
MAGIC-PRO MP-7VIP Wake On LAN Enabled: Wake on the system from the LAN card (LAN card must support wake on LAN function and the power supply must provide at least 5V/7750mA standby current) Disabled(default): Disable Wake On LAN function. Modem Ring Resume An input signal on the serial Ring Indicator (RI) Line (in other words, an incoming call on the modem) awakens the system from a soft off state.
MAGIC-PRO MP-7VIP CMOS Setup Utility - Copyright (C) 1984-2000 Award Software IRQs Activity Monitoring Primary INTR IRQ3 (COM 2) IRQ4 (COM 1) IRQ5 (LPT 2) IRQ6 (Floppy Disk) IRQ7 (LPT 1) IRQ8 (RTC Alarm) IRQ9 (IRQ2 Redir) IRQ10 (Reserved) IRQ11 (Reserved) IRQ12 (PS/2 Mouse) IRQ13 (Coprocessor) IRQ14 (Hard Disk) IRQ15 (Reserved) ON Primary Primary Primary Primary Primary Disabled Secondary Secondary Secondary Primary Primary Primary Disabled Item Help Menu Level :Move Enter:Select +/-/PU/PD:Value F10:Sav
MAGIC-PRO MP-7VIP 3. Press and follow the screen instructions to save or disregard your setting.
MAGIC-PRO MP-7VIP 3-11 PnP/PCI CONFIGURATION SETUP PnP/PCI Configuration Setup defines PCI bus slots. Run the PnP/PCI Configuration Setup as follows: 1. Choose PnP/PCI CONFIGURATION SETUP from the Main Menu and a screen with a list of options will appear. 2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.
MAGIC-PRO MP-7VIP PNP OS Installed Yes: OS supportsss Plug and Play function. No (default): OS doesnt support Plug and Play function. Note: BIOS will automatically diable all PnP resources except the boot device card when you select Yes on NonPnP O.S. Reset Configuration Data Choose Enabled or Disabled (default). Disable retains Enabled PnP configuration data in BIOS and resets the PnP configuration data in the BIOS. Resources Controlled By Choose Manual or Auto (ESCD) (default) .
MAGIC-PRO MP-7VIP CMOS Setup Utility - Copyright (C) 1984-2000 Award Software DMA Resources DMA-0 DMA-1 DMA-3 DMA-5 DMA-6 DMA-7 assigned assigned assigned assigned assigned assigned to to to to to to PCI/ISA PCI/ISA PCI/ISA PCI/ISA PCI/ISA PCI/ISA PnP PnP PnP PnP PnP PnP Item Help Menu Level :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults IRQ-x assigned to DMA-x assigned to Legacy ISA: Manually assigns IRQ / DMA to d
MAGIC-PRO MP-7VIP 3-12 PC Health Status PC Health Status option shows information about system temperature and fan speed when it is working. Run the PC Health Status as follows: 1. Choose PC Health Status from the Main Menu and a screen with a list of options will appear. 2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys. CMOS Setup Utility - Copyright (C) 1984-2000 Award Software PC Health Status Current Current Current Current Vcore 2.
MAGIC-PRO MP-7VIP 3-13 FREQUENCY/VOLTAGE CONTROL Frequency/Voltage Control option allows user to adjust CPUs settings and retain some informations inside computer when it is working. Run the Frequency/Voltage Control as follows: 1. Choose FREQUENCY/VOLTAGE CONTROL from the Main Menu and a screen with a list of options will appear. 2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.
MAGIC-PRO MP-7VIP Auto Detect DIMM/PCI clk Choose Disabled (default) or Enabled. The clock generator will turn off the DIMM clock if this slot is empty. CPU Host Clock (CPU/ PCI) Select the CPU Host Clock. The choice: default, 83/23MHz, 88/29MHz, 90/30MHz, 95/ 32MHz, 100/33MHz, 110/37MHz, 115/38MHz. 3. Press and follow the screen instructions to save or disregard your setting.
MAGIC-PRO MP-7VIP 3-14 LOAD FAIL-SAFE DEFAULTS Load Fail-Safe Defaults option loads the default system values to the system configuration fields. If the CMOS is corrupted the defaults are loaded automatically. Choose this option and the following message will appear: Load Setup Defaults (Y/N)? N To use the Fail-Safe Defaults, change the prompt to Y and press . 3-15 LOAD OPTIMIZED DEFAULTS Load Optimized Defaults option loads optimized system values to the system configuration fields.
MAGIC-PRO MP-7VIP 3-16 SUPERVISOR/USER PASSWORD These two options allow you to set your system passwords. Normally, the supervisor has a higher ability to change the CMOS setup option than the user. The way to set up the passwords for both supervisor and user are as follows: 1. Choose CHANGE PASSWORD from the Main Menu and press . The following message appears: Enter Password: 2. The first time you run this option, enter your own password up to 8 characters and press .
MAGIC-PRO MP-7VIP 3-17 SAVE & EXIT SETUP Save & Exit Setup allows you to save all modifications you have specified into the CMOS memory. Highlight this option on the Main Menu and the following message appears: SAVE to CMOS and EXIT (Y/N)? Y Press key to save the configuration changes. 3-18 EXIT WITHOUT SAVING Exit Without Saving allows you to exit the Setup utility without saving the modifications that you have specified.
Appendix A APPENDIX A FLASH MEMORY UPDATE INSTALLATION 1. Download BIOS files and flash utility from your board vendor. They are: awdflash.exe and .bin file. 2. Copy them to bootable diskette and boot from diskette. 3. The diskette cannot include memory manager e.g. emm386.exe,qemm and himem.sys, otherwise there will appear an error message insufficient memory. 4. Type awdflash filename(XXXX.bin). 5.
Appendix B APPENDIX B DRIVER INSTALLATION If you are using Windows 98 SE, you do not need to install the 4-in-1 driver as the IRQ Routing Driver and the ACPI Registry are already incorporated into the operating system. Users with Windows 98 SE may update the IDE Busmaster and AGP drivers by installing them individually. Installation : 1. Put the CD into your CD-ROM. 2. There appears a welcome window.
Appendix B SuperCops III Hardware Monitor Installation Windows95/Windows98: 1. Go to the CD-ROM disk, we suggest the CD-ROM title is D:\. 2. Find and run D:\SUPERCOP\SC3\SETUP.
Appendix C APPENDIX C THE USAGE OF RT2 Thermal Sensor Connector a: Connect to RT2. b: Connect this thermal sensor to particular device which generates lots of heat such as Hard Disk, VGA chip, etc. When connected, user could observe the temperature change from the BIOS program. VIA Hardware Monitor Setup 1. Make sure that the CD is in the CD-ROM. 2. There will appear a welcome window, please use the mouse to choose Install Driver item.
