4.9 CU.FT. BEER KEG COOLER INSTRUCTION MANUAL Model No.: MCKC490B To ensure proper use of this appliance and your safety, please read the following instructions completely before operating this appliance.
TABLE OF CONTENTS Names of the Parts _________________________________________________3 Important Safety Instructions ________________________________________ 4 Installation Instructions _____________________________________________ 4 Before Using Your Beer Dispenser ____________________________________ 4 Installation of Your Beer Dispenser ________________________________ 4 - 5 Electrical Connection _______________________________________________ 5 Installation Instructions for Beer Keg____________________
NAMES OF THE PARTS MODEL NO.
IMPORTANT SAFETY INSTRUCTIONS WARNING • • • • • • • • To reduce the risk of fire, electrical shock, or injury when using your Beer Dispenser, follow these basic precautions: Read all instructions before using the unit. WARNING: Risk of child entrapment. To avoid the possibility of child entrapment, please take the following precautions before throwing out the appliance. - Remove all doors from the unit. - Leave the shelves in place so that children may not easily climb inside.
• • • radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the Beer Dispenser not to perform properly. This unit is not designed for outside installation (ie garages, porches, etc.) Avoid locating the Beer Dispenser in excessive humidity. Plug the Beer Dispenser into a dedicated, properly installed-grounded wall outlet.
INSTALLATION INSTRUCTIONS FOR BEER KEG Keg Installation Sketch · Install the four castors with lock provided into the unit’s bottom (four screw holes pre-supplied) The two metal gaskets are used for the front two Castors. Figure (1) before installation. Figure (II) is the final version.
Installation Of CO2 Cylinder Support • Install the metal support provided onto the 4 studs located on the exterior back wall. Align the holes in the support with the studs and push down firmly. (See Figure 1) Installation Of CO2 Cylinder • The CO2 Cylinder does not come filled. The cylinder must be filled with CO2 prior to use.
Installation Of The Beer Keg • Position the beer keg directly in front of the open door. Using keg handles only, carefully lift the beer keg. (See Figure 5) • To place the beer keg inside the cabinet, brace your knees behind the beer keg. Lift the front of the keg just enough so the front edge of the keg is resting on the front edge of the Beer Dispenser bottom cabinet. (See Figure 6) • Grasp the keg handles and slide it all the way into the cabinet. Fig. 4 Fig. 5 Fig.
Spanner Faucet Wrench Spanner faucet wrench is provided for either removing or tightening connection Plastic Faucet Lever Attach the black plastic lever (pull handle) to the top of the faucet by tightening it by hand clockwise until the end, holding in the silver nut underneath so it does not turn. If there is still a small drip from the faucet, you may have tightened the plastic lever too much and may need to unscrew silver snug counterclockwise (as shown) one turn.
OPERATING YOUR BEER DISPENSER Setting The Temperature To start, turn the temperature control knob to the maximum setting (6). Allow the unit to run for 24 hours for the unit to cool properly. You may then adjust the temperature to the desired setting. In average room conditions of 70°F (21 ºC), set thermostat knob position between “4” and “5. To turn off the Beer Dispenser, rotate the control knob to the “OFF” position.
CHANGING THE REVERSIBLE DOOR This Beer Dispenser has a door that can be set to open from the left or right side. The unit is delivered to you with the door opening from the left side. To reverse the opening direction, please follow the instructions below. Caution: To avoid personal injury to yourself and/or property, we ecommend that someone assist you during the door reversal process.
CARE AND MAINTENANCE • • • • • • • Cleaning Your Beer Dispenser Turn the temperature control to "OFF", unplug the Beer Dispenser, and remove the contents. Wash the inside surfaces with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. Wash the shelves and stand with a mild detergent solution. Wipe down any electrical controls with a dry clothe. Wash the outside cabinet with warm water and mild liquid detergent.
TROUBLESHOOTING GUIDE You can solve many common Beer Dispenser problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. PROBLEM Beer Dispenser does not operate. Turns on and off frequently. Vibrations. The Beer Dispenser seems to make too much noise. The door will not close properly. POSSIBLE CAUSE Not plugged in. The circuit breaker tripped or blown fuse. The room temperature is hotter than normal.
WARRANTY MC Appliance Corporation warrants each new Beer Keg Cooler to be free from defects in material and workmanship and agrees to remedy any such defect or to furnish a new part(s) (at the company’s option) for any part(s) of the unit that has failed during the warranty period. Parts and labor expenses are covered on this unit for a period of one year from the date of purchase.
