Installation guide
pte
Check
Operation
To
Light
Standing
Pilot
Lights:
Before
using
the
range,
the
standing
pilots
must
be
lit.
They
will
stay
lit
after
turning
off
the
burners.
1.
Make
sure
all
controls
are
off
and
the
oven
and
cooktop
are
cool.
2.
Remove
surface
grates
from
the
cooktop.
3.
Lift
the
cooktop
by
both
front
corners
until
the
side
support
rods
snap
into
position.
A.
Side
support
rods
4.
Using
a
match,
light
both
burner
pilot
lights.
5.
The
surface
pilot
flames
should
be
0.4"
to
0.6"
(1.0
to
1.5
cm)
high.
A
A.
0.4"
-
0.6"
(1.0
-
1.5
cm)
6.
If
the
pilot
flame
needs
adjustment,
use
a
flat-blade
screwdriver
and
turn
the
adjusting
screw
until
the
flame
is
of
the
desired
height.
A.
Adjusting
screw
7.
Push back
on
the
side
support
rods
and
slowly
lower
the
cooktop
until
it
snaps
into
position.
8.
Push
in
and
turn
each
surface
burner
control
knob
to
the
“HI”
position.
The
flame
should
light
with
4
seconds.
OFF
8S
e
9.
If
surface
burners
do
not
ignite,
repeat
steps
3
to
6.
10.
Check
each
cooktop
burner
for
proper
flame.
The
small
inner
cone
should
have
a
very
distinct
blue
flame
44"
(0.64
cm)
to
Ya"
(1.3
cm)
long.
The
outer
cone
is
not
as
distinct
as
the
inner
cone.
A.
Outer
cone
B.
Inner
cone
11.
Turn
the
control
Knob
quickly
to
the
“LO”
position
after
the
burner
lights.
If
the
flame
goes
out,
turn
the
control
Knob
to
the
“OFF”
position.
12.
Check
each
cooktop
burner
for
proper
low
flame.
The
low
flame
should
be
a
minimum,
steady
blue
flame.
The
flame
size
should
be
44"
to
¥%"
(0.64
cm
to
0.95
cm)
high.
If
the
low
flame
needs
adjusting:
1.
Turn
control
knob
to
the
“Lo”
setting
and
remove
control
knob.
2.
Insert
a
small
flat-blade
screwdriver
into
the
valve
stem.
Turn
the
valve
adjusting
screw
to
obtain
the
smallest
flame
that
will
not
go
out
when
the
control
of
a
cold
burner
is
quickly
turned
from
“HI”
to
“Lo.”
Turn
right
to
decrease
flame
height.
Turn
left
to
increase
flame
height.
Repeat
for
other
cooktop
burners
as
needed.
A.
Valve
stem
3.
Replace
control
knob.
me
f
le
sm
gohy
Oem
opel
ony
oak
P'
geu,
(ve
dl
Ce
rrr
Check
Operation
of
Oven/Broll
Burmer
1.
Make
sure
all
controls
are
off
and
the
oven
is
cool.
2.
Open
the
oven door
to
remove
oven
racks
and
the
oven
bottom
tray.
3.
Remove
the
fasteners
holding
the
flame
spreader.
Lift
and
pull
out the
flame
spreader.
Aw
Mir
A.
Oven
bottom
tray
B.
Fasteners
C.
Flame
spreader
4.
Locate
the
pilot
light
on
the
left-hand
side
of
the
oven
burner.