Installation guide
Mobile
Home
-
Additional
Installation
Requirements
The
installation
of
this
range
must
conform
to
the
Manufactured
Home
Construction
and
Safety
Standard,
Title
24
CFR,
Part
3280
(formerly
the
Federal
Standard
for
Mobile
Home
Construction
and
Safety,
Title
24,
HUD
Part
280).
When
such
standard
is
not
applicable,
use
the
Standard
for
Manufactured
Home
Installations,
ANSI
A225.1/NFPA
501A
or
with
local
codes.
In
Canada,
the
installation
of
this
range
must
conform
with
the
current
standards
CAN/CSA-A240
-
latest
edition,
or
with
local
codes.
Mobile
home
installations
require:
m
When
this
range
is
installed
in
a
mobile
home,
it
must
be
secured
to
the
floor
during
transit.
Any
method
of
securing
the
range
is
adequate
as
long
as
it
conforms
to
the
standards
listed
above.
Product
Dimensions
Freestanding
Range
26
3/4"
(67.9
cm)
Y
(91.4.cm)
4p"
(106.7
cm)
Kd
29
7/8"
(75.9
cm)
a
(61.6
ma
Ne
24
1/4"
Installation
Clearances
Cabinet
opening
dimensions
shown
are
for
25"
(64.0
cm)
countertop
depth,
24"
(61.0
cm)
base
cabinet
depth
and
36"
(91.4
cm)
countertop
height.
If
the
cabinet
depth
is
greater
than
24" (61.0
cm),
oven
frame
must
extend
beyond
cabinet
fronts
by
4%"
(13.0
mm)
minimum.
IMPORTANT:
If
installing
a
range
hood
or
microwave
hood
combination
above
the
range,
follow
the
range
hood
or
microwave
hood
combination
installation
instructions
for
dimensional
clearances
above
the
cooktop
surface.
an
A.
18"
(45.7
cm)
min.
clearance
upper
side
cabinet
to
countertop
B.
13"
(83
cm)
max.
upper
cabinet
depth
C.
30"
(76.2
cm)
min.
opening
width
D.
For
minimum
clearance
to
top
of
cooktop,
see
NOTE™.
E.
30%"
(76.5
cm)
min.
opening
width
F.
17"
(43.2
cm)
G.
This
shaded
area
recommended
for
installation
of
rigid
gas
pipe.
H.
2"
(5.1
cm)
1.4" (10
cm)
d.2"
(5.1
cm)
K.
2"
(5.1
cm)
min.
clearance
from
both
sides
of
range
to
side
wall
or
other
combustible
material.
*NOTE:
24" (61.0
cm)
minimum
when
bottom
of
wood
or
metal
cabinet
is
covered
by
not
less
than
14"
(0.64
cm)
flame
retardant
millboard
covered
with not
less
than
No.
28
MSG
sheet
steel,
0.015"
(0.4
mm)
stainless
steel,
0.024"
(0.6
mm)
aluminum
or
0.020"
(0.5
mm)
copper.
30"
(76.2
cm)
minimum
clearance
between
the
top
of
the
cooking
platform
and
the
bottom
of
an
uncovered
wood
or
metal
cabinet.
IMPORTANT:
Some
cabinet
and
building
materials
are
not
designed
to
withstand
the
heat
produced
by
the
oven
for
baking
and
self-cleaning.
Check
with
your
builder
or
cabinet
supplier
to
make
sure
that
the
materials
used
will
not
discolor,
delaminate
or
sustain
other
damage.