32-Zone Wireless Transceiver Control Panel MG5000 V1.4 Reference & Installation Manual We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send us your comments.
Table of Contents Introduction...................................................................... 1 Features.............................................................................................. 1 Specifications...................................................................................... 1 Installation........................................................................ 2 Location and Mounting ....................................................................... Earth Ground ......
System Settings............................................................. 42 Version Number Display ................................................................... Push Button Power Reset................................................................. Installer Lock..................................................................................... Keypad Lockout Feature................................................................... Battery Charge Current........................................
Part 1: Introduction 1.1 Features • Built-in transceiver: supports all existing Magellan transmitters including the MG-REM2 and MG-2WPGM. • 32 zones (any of which can be wireless or keypad zones). • 2 on-board hardwire zone inputs. 4 zones total with ATZ. • Supports 16 PGMs (any of which can be wireless). • 32 users and 32 remote controls (one per user). • In-field upgradeable: Update the MG5000’s firmware by connecting it to a PC via a 306USB Interface and then using the Winload software (V2.
Part 2: Installation 2.1 Location and Mounting Before mounting the cabinet, push the five white nylon mounting studs into the back of the cabinet. Pull all cables into the cabinet and prepare them for connection before mounting the circuit board into the back of the cabinet. Select a centralized installation site on the main floor that isn't easily accessible to intruders and leave at least 5cm (2in) around the panel box to permit adequate ventilation and heat dissipation.
Figure 2: Magellan MG5000 Control Panel Overview "STATUS" LED: Flash once every second = Normal Flashes ON 1 second and OFF 1 second = Any trouble Always ON = Panel is using phone line Fast flash 6 seconds after power up = Installer lock enabled Press and hold the RESET button for five seconds. The STATUS LED will start flashing. Within 2 seconds of this flashing, press the reset switch again. The panel will reset to default and restart.
Figure 3: Metal Box Installation 8x10” Metal Box Installation For UL recommended installation, place the PCB one notch lower than the new mounting location. This applies to both types of metal boxes. Old Metal Box New MG5000 Compatible Metal Box = New mounting location = PCB position 11x11” Metal Box Installation For UL recommended installation, place the PCB one notch lower than the new mounting location. This applies to both types of metal boxes.
2.5 Auxiliary Power Terminals The auxiliary power supply terminals can be used to power motion detectors, keypads and other modules or accessories in the security system. A fuseless circuit protects the power supply against current overload and automatically shuts down if the current exceeds 1.1A. If this occurs, the Maximum Auxiliary Current failure will appear in the keypad’s trouble display (see Trouble Display on page 46).
2.9 Single Zone Inputs Detection devices such as motion detectors and door contacts are connected to the control panel's zone input terminals. Figure 5 demonstrates single zone input terminal connections recognized by Magellan. Once connected, the associated zone's parameters must be defined.
2.10 Advanced Technology Zone (ATZ) Connections The ATZ feature is a software oriented feature that enables two detection devices to be installed per hardwired input terminal. Each detection device has its own zone, displays its zone status on the keypad and sends its own alarm codes. Fire zones cannot be doubled.
2.11 Fire Circuits When a zone is programmed as a fire zone, the zone becomes normally open and requires an EOL resistor. If a line short occurs or if the smoke detector becomes active, whether the system is armed or disarmed, the control panel will generate an alarm. If a trouble occurs on a fire zone, the Fire Loop Trouble will appear in the keypad’s trouble display (see Trouble Display on page 46) and the control panel can transmit the Fire Loop Trouble report, if programmed, in section [866].
Part 3: Programming Methods 3.1 WinLoad Software for Windows Program the Magellan Series control panels remotely or on-site using the WinLoad Software (V2.80 or higher) for Windows®. For more information, contact your local Paradox Distributor or visit our web site at paradox.com. If you are using the WinLoad software, you must program the features (see Settings for WinLoad Software on page 44).
3.2.3 Data Display Mode In the Data Display Mode you can view the programmed contents of each section one digit at a time. To access the Data Display Mode, press the [ENTER] key after entering a section and before entering any data. The four LEDs as indicated below will begin to flash indicating that you are in the Data Display Mode.
Figure 8: Paradox Memory Key Jumper ON = Read from and/or write to memory key. Jumper OFF = Write protected (read from memory key only) Insert Paradox Memory Key onto the ‘MEMORY KEY’ connector. Paradox Memory Key PMC-3/ PMC-4 Partial view of Magellan MG5000 control panel Part 4: Access Codes The Magellan MG5000 control panel supports the following access codes: 4.1 Installer Code [397]: Used to program all control panel settings except user access codes.
4.3 Maintenance Code (Default: 1111 / 111111) The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to program all the features, options and commands except for the MG5000’s communication settings (sections [395], [397], [398], [815], [816], [817], [910], and [911]) as well as any user codes. The Maintenance code can be 4 or 6 digits in length where each digit can be any value from 0 to 9.
4.5.6 Arm Only Sections [404] to [432]: User Codes 004 to 032 Option [6] OFF = Arm Only Disabled (default) Option [6] ON = Arm Only Enabled for selected User Code The user code with this option enabled can arm assigned partitions, but cannot disarm any partitions. The type of arming is dependent on the other User Code Options selected. Please note that with the Arm Only option, the user can cancel a recently armed system by re-entering the access code before the end of the exit delay. 4.5.
Part 5: Zone Programming When programming zones, the zone assignments are dependent on the designation of the wireless transmitters, assignment of keypad zones, and the detection devices that are connected to the panel. For wireless assignment, see Wireless Transmitter Programming on page 20 or the Installer Quick Menu of the MG5000 Programming Guide. For keypad assignment, see Configuring the Keypad Zone Number on page 10. For panel hardwire detection devices, Table 3 on page 14.
5.1.3 Entry Delay 1 / Stay / Sleep Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 03 Upon regular arming, the zone is Entry Delay 1 (see Entry Delay 1 Zones on page 14). Upon Stay/Sleep arming, the zone is bypassed by the system. See Table 4 on page 17 for any exceptions. 5.1.4 Entry Delay 2 / Stay / Sleep Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 04 Upon regular arming, the zone is Entry Delay 2 (see Entry Delay 2 Zones on page 14).
5.1.11 Instant Fire Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 11 when a Instant Fire zone opens, whether it is armed or disarmed, the console will send the corresponding Alarm Report Code and the alarm is always audible regardless of other settings. Fire alarms generate an intermittent (pulsed) bell/siren output signal as shown in Figure 10 on page 16. Figure 10: Bell/Siren Output during a Fire Alarm 5.1.
5.1.17 24 Hr. Hold-up Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 17 When a 24Hr. Hold-up zone opens, whether it is armed or disarmed, the console will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 18. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Hold-up alarm. 5.1.18 24 Hr.
5.3 Zone Partition Assignment Sections [001] to [032]: Zones 1 to 32, The control panel provides the option of partitioning the security system into two completely independent systems. Sections [001] to [032] represent zones 1 through 32 respectively, where the third digit in each of these sections represents the zone's partition assignment. The zone is assigned to Partition 1 if third digit = 1, Partition 2 if third digit = 2, or both partitions is third digit = 3.
5.4.5 Intellizone Sections [001] to [032]: Zones 1 to 32 Option [6] OFF = Intellizone Disabled (default) Option [6] ON = Intellizone Enabled for Selected Zone This feature reduces the possibility of false alarms. When a zone with the Intellizone option opens, the panel does not immediately generate an alarm. First it triggers the Intellizone Delay Timer. To program the Intellizone Delay Timer, key in the desired 3-digit value (000 to 255 seconds, Default = 48 seconds) into section [713].
5.9 Zone Timers Sections [041] to [044]: Zones 1 to 4 001 to 255 X 10ms, Default = 060 The Zone Timer defines how quickly the control panel will respond to an open zone. The control panel will not display an open zone on the keypad or generate an alarm until the programmed Zone Timer has elapsed. All other zone definitions and options do not come into effect until the Zone Timer has elapsed. This feature prevents any momentary glitches from causing an alarm or unnecessary reporting.
6.3 Supervision Options The Supervision Options cannot be used with any remote controls assigned to the control panel. 6.3.1 Supervision Bypass Options Section [705]: Arming/Disarming Options Option [8] ON = Generate Supervision Loss if detected on a Bypassed Wireless Transmitter Zone (default) Option [8] OFF = No Supervision Loss if detected on a Bypassed Wireless Transmitter Zone When this feature is disabled, the Wireless Transmitter Supervision Options will follow the zone’s bypass definition.
How Do I Delete a Remote Control? 1) Press the [ENTER] key. 2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111) 3) Enter the desired [SECTION NUMBER] (from sections [651] to [682]). 4) Press the [0] button six times to delete the serial number. 6.6.3 Programming the Remote Control Buttons Sections [611] to [642]: Remote Controls 1 to 32 respectively Each remote control can be programmed to perform up to 4 different actions.
6.
Option [7] OFF Option [7] ON = Repeat Wireless Keypad 3 Signals (default) = Repeat Wireless Keypad 3 Signals Option [8] OFF = Repeat Wireless Keypad 4 Signals (default) Option [8] ON = Repeat Wireless Keypad 4 Signals Enable or disable the repetition of wireless keypads in this section. Enabling these options for keypads means that the repeater will retransmit any signals relevant to them.
Option [4] OFF Option [4] ON = Repeat Wireless Zone 20 Signals (default) = Repeat Wireless Zone 20 Signals Option [5] OFF Option [5] ON = Repeat Wireless Zone 21 Signals (default) = Repeat Wireless Zone 13 Signals Option [6] OFF Option [6] ON = Repeat Wireless Zone 22 Signals (default) = Repeat Wireless Zone 22 Signals Option [7] OFF Option [7] ON = Repeat Wireless Zone 23 Signals (default) = Repeat Wireless Zone 23 Signals Option [8] OFF = Repeat Wireless Zone 24 Signals (default) Option [8] ON = R
Section [557] (Repeater 1) and Section [567] (Repeater 2): Wireless Repeater Options Option [1] OFF Option [1] ON = Repeat Wireless 2-Way PGM 9 Signals (default) = Repeat Wireless 2-Way PGM 9 Signals Option [2] OFF Option [2] ON = Repeat Wireless 2-Way PGM 10 Signals (default) = Repeat Wireless 2-Way PGM 10 Signals Option [3] OFF Option [3] ON = Repeat Wireless 2-Way PGM 11 Signals (default) = Repeat Wireless 2-Way PGM 11 Signals Option [4] OFF Option [4] ON = Repeat Wireless 2-Way PGM 12 Signals (de
Part 7: Arming and Disarming Options 7.1 Switch to Stay Arming if no Entry Delay is opened Section [741]: Partition 1, Section [742] = Partition 2 Option [5] OFF = Switch to Stay Arming Disabled (default) Option [5] ON = Switch to Stay Arming Enabled If a user Regular arms a partition, but does not exit through (open and close) an entry delay zone during the exit delay, the control panel can be programmed to switch from Regular arming to Stay arming. 7.
7.8 Restrict Arming on Wireless Supervision Trouble Section [703]: Arming/Disarming Options Option [7] OFF = Permit arming on wireless supervision failure (default) Option [7] ON = Restrict arming on wireless supervision failure If this option is enabled, the control panel will not arm the system if the control panel detects a wireless supervision trouble on one or more zones. The control panel will not arm the system until all wireless supervision trouble conditions are rectified.
7.11 Auto-Arming Options (Not to be used with UL installations) Section [741] = Partition 1, [742] = Partition 2 [3] [4] OFF OFF Regular OFF ON Sleep ON OFF Stay When using Timed Auto-arming or No Movement Auto-arming, the control panel can Regular, Sleep or Stay arm the selected partition. 7.12 One-Touch Arming (Not to be used with UL installations) Section [703]: Options [1] to [3] Option [1] ON = Press & hold the [ARM] key for One-touch Regular Arming.
7.17 No Exit Delay When Arming with Remote Control Section [704]: Arming/Disarming Options Option [8] OFF = Provides Exit Delay When Arming with a Remote Control (default) Option [8] ON = No Exit Delay When Arming with a Remote Control When the option is enabled, the panel cancels the exit delay (arms instantly) when a partition is armed with a remote control. When disabled, the exit delay timer will start when a partition is armed with a remote control. 7.
Part 8: Alarm Options 8.1 Bell Cut-Off Timer Section [747] = Partition 1, [748] = Partition 2 000 = Disabled, 001 to 255 minutes, Default = 4 minutes, 5 minutes minimum for ULC installations After an audible alarm, the bell or siren will stop upon disarming of the partition or when the Bell Cut-Off Timer has elapsed, whichever comes first. 8.2 Recycle Alarm After the Bell Cut-Off Timer and the Recycle Delay have elapsed, the control panel will re-verify the zone status.
8.5 Tamper Bypass Options Section [705]: Zone Options Option [5] OFF = Tampers on bypassed zones will be ignored Option [5] ON = Will generate a tamper if detected on a bypassed zone (default) With option [5] off, the Tamper Recognition feature follows the zone bypass definition. This means the control panel will ignore any tampers detected on a bypassed zone. With option [5] on, Tamper Recognition ignores the bypass definition.
Part 9: Reporting and Dialer settings The following section explains all the features and options that must be programmed in order for your security system to properly report system events to a monitoring station. When an event (e.g. zone in alarm) occurs in the system, the control panel verifies if a report code was programmed in the section corresponding to the event (except Ademco Contact ID “All Codes”).
9.6 System Trouble Report Codes Section [865] to [869] When the system generates one of the instances listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of system trouble. Section [865] • N/A • AC Failure: The control panel has detected a loss of AC power. Transmission of this report code can be delayed. • Battery Failure: Backup battery is disconnected or battery voltage is low. • Auxiliary Supply: Auxiliary power supply has overloaded.
9.9 Monitoring Station Telephone Numbers Section [815] = Phone#1, [816] = Phone#2, [817] = Backup Phone#, [818] = Pager #, [819] = Numeric Message Sent with Pager Reporting: Up to 32 digits The MG5000 control panel can dial up to 2 different monitoring station telephone numbers. You can enter any digit from 0 to 9 and any special keys or functions (see Table 6 on page 35) up to a maximum of 32 digits.
9.11.2 Ademco Express The Ademco Express is a high-speed reporting format, which will transmit the 2-digit (00 to FF) report codes programmed into sections [860] to [876]. 9.11.3 Ademco Contact ID Ademco Contact ID is a fast communicator format that uses tone reporting instead of pulse reporting. This communicator format also uses a pre-defined list of industry standard messages and report codes that will suit most of your basic installation needs.
9.13 Pulse Ratio Section [800]: Dialer Options Option [7] OFF = European Pulse Ratio of 1:2 Option [7] ON = U.S.A. Pulse Ratio of 1:1.5 (default) When using Pulse dialing, you can select one of two Pulse Ratios. Although most European countries use the 1:2 pulse ratio, the 1:1.5 ratio may provide better results in some cases. The same applies for North American countries. If the 1:1.5 pulse ratio is not providing the desired results, the 1:2 ratio may be used. 9.
9.21 Closing Delinquency Delay Section [719] 000 = Disabled, 001 to 255 days, Default = Disabled At midnight every day, the control panel will verify when the partition was last disarmed. If the partition has not been armed within the time programmed in the Closing Delinquency Delay, the control panel will transmit a Closing Delinquency event to the monitoring station. Example: The Closing Delinquency Timer for partition 1 in section [719] is programmed for 005 days.
9.26 Pager Reporting Delay Section [834]: Communication Timers 000 to 255 seconds, Default = 20 seconds When using the Pager Reporting Format, the control panel will wait for the Pager Delay period before transmitting the report codes. This is to allow time for the pager system to provide a dial tone or to bypass the “welcome” message before sending data. 9.27 Pager Reporting Message Repetition Section [835]: Communication Timers 000 to 255 times, Max.
Part 10: Programmable Outputs A PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the system. For example, a PGM can be used to activate bells or strobe lights, open/close garage doors and much more. When a PGM activates, the control panel triggers any device or relay connected to it. The Magellan console includes two onboard PGMs. It can support up to a total of 16 PGMs (e.g.
Option [5] OFF = PGM Pulse once every 30 seconds disabled (default) Option [5] ON = PGM Pulse once every 30 seconds enabled When armed, the PGM will pulse once every 30 seconds. Option [6] OFF = PGM Pulse on any alarm disabled (default) Option [6] ON = PGM Pulse on any alarm enabled This option sets the PGMs to pulse on any alarm. Option [7] OFF = PGM Pulse on any alarm Partition 1(default) Option [7] ON = PGM Pulse on any alarm Partition 2 Program PGMs to pulse during an alarm for either partition.
Part 11: System Settings 11.1 Version Number Display Enter section [980] to view the version number of the panel. The first digit will appear. Press [ENTER] to scroll through each consecutive digit (the keypad will beep twice after every digit in the version number). Once the version number has been fully displayed, an acknowledgement beep (3 beeps) will sound and the first digit will be displayed again. 11.
11.
Part 12: Settings for WinLoad Software WinLoad has not been verified by UL. 12.1 Panel Answer Options The following two options define how the control panel answers an incoming call from a computer using the WinLoad Software for Windows®. 12.1.
12.6 Answer WinLoad Software [ENTER] + [INSTALLER CODE] + [FORCE] In order to perform on-site upload/download connect your computer directly to the control panel using an ADP-1 line adapter. In the WinLoad software set Dialing Method to Blind Dial. Program the panel telephone number in WinLoad software and follow the instructions on the ADP-1 adapter.
Part 13: User Operation 13.1 Alarm Display If an alarm has occurred on a zone, the respective zone LED will flash, the [MEM] key will light up, and the zones will be stored in memory. These respective LEDs will continue to flash until disarming even if the zones are restored. To exit this mode and switch to live display mode before disarming, press the [CLEAR] key. Once the system is disarmed, the zones’ LEDs will turn off, while the [MEM] key remains lit.
INDEX Numerics 24 Hr. Burglary Zones ......................................................16 24 Hr. Buzzer ...................................................................16 24 Hr. Freeze Zones ........................................................17 24 Hr. Gas Zones ............................................................17 24 Hr. Heat Zones ...........................................................17 24 Hr. Hold-up Zones ......................................................17 24 Hr.
Follow Zones ................................................................... 15 Force Arming ................................................................... 12 Force Zones .................................................................... 19 G Ground ............................................................................... 2 H Hardware Reset ............................................................... 42 I Installation ...................................................................
Repetition .........................................................................39 Report ..............................................................................38 Report Code, Special Cold Start ....................................................................34 Installer In ...................................................................34 Installer Out .................................................................34 Test Report .........................................................
Zone Options Delay Before Alarm Report Code Transmission ............... 19 Force Zones ................................................................ 19 Zone Programming .......................................................... 14 Zone Restore Report Options .......................................... 38 Zone Shutdown, Auto ...................................................... 18 Zone Timers ....................................................................
Warranty Paradox Security Systems Ltd. (“Seller”) warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded.
paradox.
