Owner’s Manual • Guide d’Utilisation • Manual del Propietario LED Rechargeable Flashlight System Système de Torche Rechargeable LED Sistema de linterna LED recargable
For Your Safety Please Read Read all safety instructions in this manual before attempting to use the ML150LR™/ML150LRS™ LED Rechargeable Flashlight System. Keep this manual for future reference. It contains important information about safe operation and maintenance of the product.
• Do not use non-rechargeable batteries in your Rechargeable Flashlight System. Use only a MAG® rechargeable battery pack (ML150LR™ Model No. 485-000-034), (ML150LRS™ Model No. 485-000-075). • For prolonged storage, remove the battery pack and store it separately in a non-conductive wrapping, such as a plastic bag. • Carefully follow steps listed under “Inspection and Maintenance” in this manual. • Always use genuine ML150LR™/ML150LRS™ replacement parts and accessories.
Getting Started LED Rechargeable Flashlight System Système de Torche Rechargeable LED Sistema de Linterna Recargable LED Contents Getting Started. . . . . . . . . . . . . . . . . . . . . 4 The Flashlight. . . . . . . . . . . . . . . . . . . . . . 5 The Charging Cradle. . . . . . . . . . . . . . . . . 6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . 7 Battery/Battery Charging . . . . . . . . . . . . .
Section 1 The Flashlight 1 2 3 5 4 1. Face Cap - The removable face cap, which is threaded onto the head, is O-ring sealed and retains the polycarbonate lens and the precision-engineered reflector that is the heart of the optical system. 3. Switch - 2. Head - The head houses the reflector and the LED module. The flashlight’s Quick-Adjustable Beam operates by rotating the head. About ¼ turn of the head causes the beam to vary between a wide floodlight setting and a narrow spotlight setting (Fig. 1).
Section 2 The Charging Cradle Constructed of engineering grade thermoplastics, this Charging Cradle unit has many features. Input can be from 12–14 volts (automotive installations) or 120-240 volts AC, when used with a converter for charging indoors. Fig. 4A Fig. 3 Flashlight in the Charging Cradle Quick-Release Button Fig. 4B LED Charging Indicator (Green/Red/Orange) To remove the flashlight from the charging cradle: Grasp the flashlight, press the quick-release button (Fig. 4A) and lift up (Fig.
Section 3 Installation A Typical Installation 1. Locate and mount the cradle using appropriate screws and anchors for the location and material. O CAUTION: Make sure cable cannot be pinched. If cable is pinched it can cause immediate short and wires can get hot, melt plastic, and create a fire hazard. 2. Attach end of DC power cord or AC converter to charging cradle by inserting round plug into power connection port in the side of the charging cradle (Fig. 6, 7 & 10).
Section 4 The Battery Your Battery’s First Charge Is Important! First Charge Procedure To assure the freshness of your battery and to avoid any operational problems in shipping, it has been packaged in an UNCHARGED state. For optimum operation of your flashlight, it should be charged a full 6 hours … before using for the first time. 1. Connect charging cradle to the AC converter or DC accessory cord (Fig. 10). 2. Plug into wall receptacle (AC) or DC power source cord. 3.
Section 4 Battery Charging After the first (6-hour) charge, the total time to fully charge a fully discharged battery is approximately (ML150LR™-2.5 hours) (ML150LRS™-1.5 hours). The charging cradle is provided with an LED that indicates battery charge status by blinking and changing color (Fig. 11), as seen in the accompanying chart.
Section 5 Operation - Getting the most out of Your ML150LR™/ML150LRS™ LED Rechargeable Flashlight System Switch Operation Your Flashlight’s Function Sets and the Functions Within Each Set The ML150LR™/ML150LRS™ LED flashlight includes powerful new electronics, providing five different functions to choose from.
Section 5 Operation - Getting the most out of Your ML150LR™/ML150LRS™ LED Rechargeable Flashlight System METHOD 1 1. Unscrew the tail cap, backing it out of the barrel far enough that the flashlight will not turn on. (Note: This may require the tailcap to be removed from the barrel entirely). 2. Pause for 2 seconds. 3. Press the switch button and keep holding it down. 4. While still holding down the switch button, screw the tail cap back in until it is tight. 5. Keep holding down the switch button.
Section 6 Troubleshooting Specifications and Accessories If you have questions or need assistance, please call our warranty/repair facility at (800) 283-5562, in the U.S.A. only, or (909) 947-1006 outside the U.S.A. Problem Cause/Correction Flashlight: Does not light 1. Make sure battery is installed, with positive (+) end toward head of flashlight. 2. Make sure large end of battery spring is snapped into tailcap. 3. Tighten tail cap – make sure unplated area of tail cap and barrel are clean.
Section 7 Warranty Information LIMITED WARRANTY (LIFETIME IN NORTH AMERICA; TEN YEARS ELSEWHERE): Mag Instrument, Inc., 2001 South Hellman Ave., Ontario, California, USA 91761, warrants to the first retail purchaser of this ML150LR™/ML150LRS™ flashlight that it is free from defects in parts and workmanship. In North America, this warranty lasts for the life of that purchaser. In the rest of the world, it lasts for ten years from the date of first retail purchase.
• Mise au point rapide – Réglage du faisceau d'un mode diffus à un mode étroit par rotation de la tête d'environ ¼ de tour • Fast Focusing – Spot to Flood with about ¼ turn of the head CORPORATE OFFICE MAG INSTRUMENT, INC. 2001 South Hellman Ave. P.O. Box 50600 Ontario, California U.S.A. 91761-1083 Warranty: (800) 283-5562 or (909) 947-1006 fax: (909) 947-5041 e-mail: warranty@magmail.com Sales & Parts: (800) 289-6241 or (909) 947-1006 email: salesdesk@magmail.com ©2018 Mag Instrument, Inc. www.maglite.
