Owner manual

ManualsBrandsMag Layers USA ManualsHardwareMHQC-2520C

(1) SHAPES AND DIMENSIONS

A: 2.90 Max. mm

B: 2.54 Max. mm

C: 2.03 Max. mm

D: 1.3 Typ. mm

E: 0.45± 0.1 mm

(2) ELECTRICAL SPECIFICATIONS

SEE TABLE 1

TEST INSTRUMENTS

L,Q : HP 4291B IMPEDANCE ANALYZER (or equivalent)

SRF : ENA E5071B NETWORK ANALYZER (or equivalent)

RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)

(3) CHARACTERISTICS

(3)-1 Operate temperature range ...... －40℃～＋125℃

(Including self temp. rise)

(3)-2 Storage temperature range ...... －40℃～＋125℃

Page-1/7

MHQC-2520C-SERIES

MAG.LAYERS

Summary of content (8 pages)

PAGE 1
(1) SHAPES AND DIMENSIONS A: 2.90 Max. mm B: 2.54 Max. mm C: 2.03 Max. mm D: 1.3 Typ. mm E: 0.45± 0.1 mm (2) ELECTRICAL SPECIFICATIONS SEE TABLE 1 TEST INSTRUMENTS L,Q : HP 4291B IMPEDANCE ANALYZER (or equivalent) SRF : ENA E5071B NETWORK ANALYZER (or equivalent) RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent) (3) CHARACTERISTICS (3)-1 Operate temperature range ...... －40℃～＋125℃ (Including self temp. rise) (3)-2 Storage temperature range ...... －40℃～＋125℃ MAG.
PAGE 2
TABLE 1 MAGLAYERS Inductance Percent L Freq. Quality Q Freq. SRF DCR IDC PT/NO. L(nH) Tolerance (MHz) Min. (MHz) (MHz)Min. (Ω) Max. (mA) Max. MHQC-2520C-4N1□ 4.1 J,K 50 75 1500 6000 0.05 1600 MHQC-2520C-7N8□ 7.8 S,J,K 50 70 500 3800 0.05 1600 MHQC-2520C-10N□ 10 J,K 50 60 500 3600 0.06 1600 MHQC-2520C-12N□ 12 J,K 50 60 500 2800 0.06 1500 MHQC-2520C-18N□ 18 G,J,K 50 62 350 2700 0.07 1400 MHQC-2520C-22N□ 22 G,J,K 50 62 350 2050 0.
PAGE 3
(4) RELIABILITY TEST METHOD Item Solderability Specifications Test conditions The metalized area must have 95% Dip pads in flux and dip in solder pot minimum solder coverage. (96.5 Sn/3.5 Ag solder) at 255°C ±5°C. Resistance to There must be no case deformation Inductors shall be reflowed onto a PC board soldering heat or change in dimensions. using 96.5 Sn/3.5 Ag solder paste. Inductance must not change more Solder process shall be at a maximum than the stated tolerance.
PAGE 4
Item Specifications Test conditions Low There must be no case deformation Inductors shall be subjected to temperature temperature or change in dimensions. -40±2℃ for 48±12 hours. storage Inductance must not change more Measure the test items after leaving the than the stated tolerance. inductors at room temperature and humidity for 1 to 2 hours. Resistance to There must be no case deformation, Inductors must withstand 6 minutes of solvent change in dimensions, or alcohol or water.
PAGE 5
(5) RECOMMENDED SOLDERING CONDITIONS (Please use this product by reflow soldering) (5)-1 RECOMMENDED FOOTPRINT Unit: mm 2.54 1.02 1.27 1.02 (5)-2 RECOMMENED REFLOW PATTERN T e m p e r a tu r e ( ℃ ) S o ld in g 260℃ 300 260 200 P r e h e a tin g N a tu r a l C o o lin g 150 100 50 T im e 1 to 4 m in . 10 sec m o r e th a n 2 m in .
PAGE 6
(6) PACKAGING (6)-1 CARRIER TAPE DIMENSIONS (mm) P P1 P0 W t W : 8.0 mm P : 4.0 mm P0 : 4.0 mm P1 : 2.0 mm t : 0.22 mm (6)-2 TAPING DIMENSIONS (mm) There shall not continuation more than two vacancies of the product. (360 mm) Leader. Blank (50 pitches) Chip Blank (70 pitches) (6)-3 REEL DIMENSIONS D C B A A : 180 mm B : 60.0 mm C : 13.0 mm D : 14.4 mm E : 8.4 mm E MAG.
PAGE 7
(6)-4 TOP TAPE PEEL STRENGTH The force for tearing off cover tape is 0.1~0.6(N) in the arrow direction at the following conditions: Temperature : 5 ~ 35℃ Humidity : 45 ~ 85% Atmospheric pressure : 860 ~ 1060 hpa 160 ~ 180。 Top cover tape Base tape (6)-5 QUANTITY 2000 pcs/Reel (6)-6 The products are packaged so that no damage will be sustained.
PAGE 8
TYPICAL ELECTRICAL CHARACTERISTICS MAG.