User’s Manual XRouter (MIH-120) acsense R .
Copyright Copyright © 1999 by this company. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from Macsense Connectivity, Inc. Macsense Connectivity, Inc. reserves the right to revise this documentation and to make changes in content without obligation among Macsense Connectivity, Inc. to provide notification of such revision or change.
Safety Precautions 1. Follow all warnings and instructions marked on the product. 2. Slots and openings on the device are provided for ventilation. To protect it from overheating, these openings must not be blocked or covered. 3. Do not use or store this product in an environment that exceeds temperature and humidity specifications. Do not place this product near a radiator or heat register, or in a built-in installation unless adequate ventilation is provided. 4.
Table of Contents ABOUT THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . .1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 BEFORE YOU START . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Items Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .4 EASY INSTALLATION . . . . . . . . . .
About This Manual ABOUT THIS MANUAL This user manual describes how to connect a LAN to the Internet using the XRouter Internet Sharing Hub, MIH-120. This manual assumes you are familiar with the basics of personal computing and network environments.
Introduction INTRODUCTION Thank you for purchasing the XRouter MIH-120 Internet Sharing Hub. The XRouter functions as an easy-to-use communication device that allows you to connect a local area network (LAN) to the Internet affordably. With the XRouter you can get as many as 252 Macintosh or PC users online simultaneously through just one cable line or DSL, and one ISP account. The XRouter installs quickly and easily, and best of all, it’s a breeze to use.
Introduction 4-Port Ethernet Hub Inside In addition to providing Internet sharing capability, the XRouter also functions as an Ethernet hub, offering four 10BASE-T, RJ-45 ports that allow you to connect a series of computers to form a small LAN. Easy Configuration The XRouter can be configured through a Web browser, and features Web-based management for a simple, intuitive set up.
Before You Start BEFORE YOU START Package Overview Please check to make sure your XRouter package includes the items listed below before setting up your XRouter.
EASY INSTALLATION Hardware Installation Before connecting the XRouter to your LAN please verify that your cable or DSL service is active and operating correctly. If you are experiencing difficulties with your cable or DSL service, please contact your service provider before proceeding with this installation.
Easy Installation Connecting Computers to the XRouter When you have finished connecting the XRouter to your DSL or cable modem, you can begin connecting the Macintosh or PC computers in your local area network to the XRouter. There are two common methods for connecting the computers in your LAN to the XRouter: (1) plugging computers directly into the XRouter, and (2) connecting the XRouter to your LAN hub.
2. Plug one RJ-45 connector (of a standard twisted-pair Ethernet cable) to the XRouter’s No. 4 LAN port. 3. Plug the other end of this Ethernet cable into an available port on the network hub. (NOTE: Multiple network hubs can be connected to the XRouter’s LAN ports No.1-3 if these hubs are equipped with uplink ports. By daisy-chaining a series of hubs, you can connect up to 252 users to the XRouter.) LAN WAN Reset Ethernet Cables Hub Mac Cable Or DSL Modem PC Figure 1.
Easy Installation Software Configuration Setting Up the TCP/IP Congratulations on installing the XRouter’s hardware! In the next pages we will show you how to enable communication between the XRouter and its managing and client computers. Part of the process of enabling communication involves setting the IP addresses for the computer that will be directly managing the XRouter’s operations and the client computers that will be receiving Internet access from the XRouter.
4. To install the TCP/IP protocol: a. Keep your copy of Windows 95/98 CD-ROM on hand. (You will need it for this installation.) b. Click the Add... button from the Configuration list of the Network window. A new window appears. c. Double-click Protocol. Then, in the Select Network Protocol window, choose Microsoft on the Manufacturers list, and select TCP/IP on the right side of the list. d. Follow the instructions that appear on the monitor to complete the installation.
Easy Installation 5. After double-clicking the installed TCP/IP protocol, the TCP/IP properties window appears. To let the computer’s TCP/IP values be automatically assigned by the XRouter’s DHCP server: a. Click the IP Address tab from the TCP/IP properties window. b. Select the item Obtain IP address automatically. The XRouter automatically assigns values for the computer’s Gateway, DNS Configuration, and IP Address. 6.
Assigning TCP/IP Values Manually If you already have a DHCP server on the network, or if you prefer not using the XRouter’s DHCP server to assign TCP/IP values automatically, you can input these values manually. To enter values for the managing computer’s address manually: 1. Click the IP Address tab from the TCP/IP properties window. 2. In the IP Address field enter “192.168.1.x” where x is any variable of your choice ranging from 2 - 252. Enter 255.255.255.0 in the Subnet Mask field.
Easy Installation Mac OS TCP/IP Configuration 1. Open the TCP/IP control panel. 2. In the Connect via menu select the Ethernet interface that is installed on your computer. 3. In the Configure pull-down menu that appears, select Using DHCP Server to allow the built-in DHCP server of the XRouter to assign an IP address and other TCP/IP configuration information to the client automatically. Do this for each client that needs Internet access through the XRouter. 4.
Assigning TCP/IP Values Manually If you already have a DHCP server on the network, or if you prefer not using the XRouter’s DHCP server to assign TCP/IP values automatically, you can input these values manually. To enter values for the managing computer’s address manually: 1. In the Connect via menu select the Ethernet interface that is installed on your computer. 2. In the Configure menu select Manually. a. In the IP Address field, enter “192.168.1.
Easy Installation Setting Up the XRouter Through a Web Browser Now that you have finished configuring the TCP/IP addresses of the client and managing computers, you can begin configuring the XRouter’s Internet settings. This can be done through a standard Web browser (such as Netscape Navigator, Netscape Communicator, or Microsoft Internet Explorer). (IMPORTANT: Before following the instructions below you must find out if your ISP is providing dynamic or static IP addressing.
5. The OnePage Setup window appears. Note that this page is divided into two basic sections -- Private IP Address, and Public IP Address. Host Name - This is an optional section. Some ISPs require a host name in order to be recognized by their systems. Your ISP should provide this if needed for their systems. Private IP Address - This section can be used to change the XRouter’s internal IP Address that is visible to the client computers on the LAN.
Easy Installation 2. Enter the static IP address provided by your ISP in the field located immediately to the right of “Specify an IP Address.” 3. Leave the Public Subnet Mask as the default setting. 4. In the Default Gateway IP Address field, enter the information provided by your ISP. Note that your ISP may refer to this information as a “Gateway/Router IP Address.” Also note that this number is not the same as the IP Address value that you entered in step 2. 5.
Advanced Configuration ADVANCED CONFIGURATION Please refer to the previous chapter on how to enter the Web Management page of the XRouter. The Advanced Menu contains four sub-menus including DHCP Settings, Virtual Server, Device Admin, and Status Monitor. DHCP Server Settings To alter the starting IP Address range, the number of users that are automatically assigned IP adressses on the LAN, or to disable the DHCP server, you must enter the DHCP Settings page to make changes.
Advanced Configuration Virtual Server It is possible to set up your own Web or FTP server on your network for external Internet users to access. Internet users simply need to enter the IP address that has been assigned to you. The XRouter will redirect the request of the Internet user to the specified internal hidden IP address of the TCP port request. (NOTE: It will be much more convenient to have a fixed address from your ISP.
Advanced Configuration Device Administration This page displays information about the firmware version and MAC address of this XRouter. You can change the password or reset the device. Selecting Yes to the Factory defaults erases previously configured settings, returning the unit to its original default settings. Status Monitor This page provides information on the working status of the XRouter. DMZ (DeMilitarized ) Host This feature will open all in/out accesses for one LAN computer.
Advanced Configuration Firmware Upgrade Macsense is continually improving the firmware (software programmed on a PROM) in each of its products. The XRouter is shipped with the most up to date software available at production time. If a firmware upgrade becomes available, it will be posted in the “Service and Support” section of our Web site. To upgrade the XRouter, you will need the TFTP client and the firmware file named “Code.bin.” These two files can be found on our Web site at www.macsensetech.com.
Troubleshooting TROUBLESHOOTING This chapter provides solutions to problems that may occur during installation and operation of the XRouter MIH-120. 1. The Link LED is off. • Check that all connectors are firmly plugged-in. • Check the power adapter making sure it is plugged into an electrical outlet. 2. The collision LED is always lit. • Make sure the 10BASE-T cable has not exceeded the maximum 100-meter length limit.
Appendix A APPENDIX A - Specifications Standards Compliance IEEE 802.3 10BASE-T TCP/IP, DHCP, DNS WAN Interface One 10BASE-T RJ-45 port LAN Interface Four 10BASE-T RJ-45 ports Web management Yes LED Display Power, Link/Activity for WAN/LAN ports, Collision/Partition for LAN ports Environment Operation Temperature 0~45°C (32~113°F) Storage Temperature -20~70°C (-4~158°F) Humidity 0~90% Dimensions LxWxH (mm) 142x236x46 LxWxH (in.) 5.59x9.29x1.
Appendix B APPENDIX B - Hardware Description Power green Ready/Test orange Indicates that there is power to the unit. Flashes during boot up WAN Port Link green Indicates proper a connection with the Internet Ethernet connection. Activity orange Flashing LED indicates that data packets are flowing through the WAN port.
Hardware description Rear Panel Description LAN WAN Reset LAN Ethernet Ports - Four 10BASE-T Ethernet network (RJ-45) ports used for linking hub/computer in a Local Area Network to the XRouter. WAN Ethernet Port - One Wide Area Network port for connecting the XRouter to the Internet via a cable or DSL modem. Reset Button - Used for resetting the XRouter’s IP Address information and user password to the factory default settings.
Appendix C APPENDIX C - Glossary DHCP DHCP is a protocol for automatic IP configuration. Client side computer can get one IP from DHCP server automatically. Using DHCP can save the effort of setting IP for every LAN computers. Domain Name A name that identifies one or more IP addresses. For example, the domain name "microsoft.com" represents many IP addresses. Domain names are used in URLs to identify particular Web pages. For example, in the URL http://www.pcwebopedia.com/index.
Appendix C ISP Short for Internet Service Provider, a company that provides access to the Internet. For a monthly fee, the service provider gives you a software package, username, password and access phone number. Equipped with a modem, you can then log on to the Internet and browse the World Wide Web and USENET, and send and receive e-mail. Local Area Network (LAN) A computer network that spans a relatively small area. Most LANs are confined to a single building or group of buildings.
