��������������� User manual ���������������
The following product named "HDV-Recorder" carries the CE seal of conformity on the basis of the guidelines 89/336/EWG of the Commission of the European Community mutual recognition of their conformity. This recorder is meant for use with hard-drives carrying the CE seal of conformity.
Contents Page 1. General information.......................................................................................... 5 2. HDV-Recorder .................................................................................................... 5 2.1 What is the HDV-Recorder? .................................................................. 5 2.2 The functions of the HDV-Recorder ..................................................... 6 2.3 Supported modes ..................................................
Legal notices To avoid making mistakes during operation, we recommend that you carefully follow the instructions provided in this manual. We have taken a great deal of care whilst programming and checking this software. Nevertheless, since it is not possible to guarantee totally error-free software applications in all environments and at any time, we unfortunately cannot rule out the possibility that some errors may have crept in.
1. General information Congratulation on purchasing the HDVRecorder! We would like to thank you for putting trust in our company and hope that this product shall meet your expectations. Telefonsupport Ring vår support för tekniska frågor. Ha systemets serienummer tillgängligt. Måndag-Fredag 10.00 till 16.00 019-12 38 07 This manual explains how to use the HDVRecorder, its on screen menus and the single functions.
IEEE 1394. The recorder stores this material if you wish. After that, the video can be output digitally to DVD or analogue via VGA to a hi-res TFT monitor with a resolution of up to 1920 x 1200 pixels and up to 60 Hz frame rate. 3. Connections 2.
optic cable to connect with a digital audio amplifier. Switching to either is not required as the signal is output both analogue and digitally at the same time. If you are using a PS2 keypad/keyboard, connect it with the purple keyboard port (3) at the back of the recorder. Connect your USB keypad by plugging it into any of the USB ports found on the front or back (5). start from CD. Now select if you wish to start a complete installation (all data is deleted!) or an update installation.
To power down the HDV-Recorder, select the `Power Off´ item in the main menu with the keypad/keyboard. You can read how to select a menu item in the next chapter. Interlacing: This activates and deactivates the De-Interlacing mode. 7. The single menus Display: This sub-menu allows you to set the monitor resolution. PAL: In this sub-menu, you can select whether PAL videos are played back in a 50 or 60 Hz mode. 7.1 The Main Menu Power Off: This switches off the recorder.
with the arrow up/arrow down keys, and once you have pressed the Ok key, the recorder software shall ask you: `Start recording?´ 7.3 The Playback Menu Make sure to select `Yes´ and press the Ok key to begin recording the video to the hard-drive. (Pressing the Exit key or selecting `No´ would return you to the Record Menu.) If you have accidentally selected an already used storage bank, the system will warn you about it.
Once you have stopped playback, the system returns to the normal live signal video display or a grey screen appears with the text `No HDV Signal´. This menu works just like the Playback Menu. However, the item `Play all films´ is missing. Requirement for sending and copying a film is a camera with a recording mode or a recorder. With the `cut and paste´ function, you can move the position of the films in order to rearrange the order for the `Play all films´ mode.
your recorded video. 7.7 The Preference Menu After entering the menu, a requester appears, allowing you to select the film that is to be trimmed. After selecting, the trim menu appears: In this menu, you can use the arrow up and down keys to select either `De-Interlaced´ or `Loop´. In the background, you can see the first frame of the footage. Use the key arrow up to select the function In (for the In-point). The selection turns red.
7.8 The PAL Menu In this menu, you can use the left/right arrows to switch between `60 Hz monitor´ and `50 monitor´. If the connected monitor supports a frame rate of 50 Hz, please select `50 Hz monitor´ so that PAL videos can be played in 50 Hz mode. If the monitor only supports 60 Hz, it is necessary to select `60 Hz monitor´ (this is also the setting by default). In this case, the PAL signal is displayed with the aid of interpolation and is rendered `up´ to the required 60 Hz.
example, we had chosen 1920x1200, most projector beamers would show no picture and the user would hence not be in a position to set t the required resolution. This default setting can be brought back any time by pressing the `Reset monitor´ key for a longer time (app. 10 seconds). If, for example, the recorder has been used with a 1920x1200 monitor and then is to be used in combination with a 1024x768 projector in the mean time, the projector will initially display no picture.
260-04/06
