MR8mk2 High Resolution Powered Studio Monitor OWNER’S MANUAL
MR8mk2 Important Safety Instructions 18. This apparatus has been equipped with a rocker-style AC mains power switch. This switch is located on the rear panel and should remain readily accessible to the user. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 19. The MAINS plug or an appliance coupler is used as the disconnect device, so the disconnect device shall remain readily operable. 4. Follow all instructions. 5. Do not use this apparatus near water. 6.
Contents • High-resolution, powered studio reference monitor IMPORTANT SAFETY INSTRUCTIONS................................................2 • Ultra-low distortion 8" woofer INTRODUCTION................................................................................
MR8mk2 Introduction The MR8mk2 Mackie Reference Monitor is the perfect solution for those ready to step up to a truly professional, high-output monitoring system. The completely re-voiced MR8mk2 features all-new high-end drivers, delivering unmatched low frequency extension and clear, articulate highs. The MR8mk2’s precision Class A/B amplification (100W LF / 50W HF) offers class-leading power, tons of connection options and simple acoustic controls for room correction.
We realize that you can’t wait to hook up your new Mackie MR8mk2 Studio Monitors and try them out. Nevertheless, please take the time to read this page NOW, and the rest can wait until you’re good and ready. 1. Turn the INPUT LEVEL [2] control on the back of the cabinet down (fully counterclockwise) before turning on the monitor for the first time. 2. Set the power switch [5] on the back panel off.
MR8mk2 Rear Panel Description This is where the signal is connected to the monitor and adjustments are made to the frequency response of the speakers to match the monitor’s location and the room’s environment. 2. INPUT LEVEL 1. SIGNAL INPUTS • The MR8mk2 is designed to operate with a +4 dBu signal when the input level control is in the max position. In other words, wide open. • Refer to the Quick Start section on page 5 for the level-setting procedure.
It’s a real rush to mix really loud. But remember that the resulting mix only sounds good when you play it at least that loud. However strange it may sound, mixes made at lower levels sound even better when played loud, perhaps even a bit bigger than life. Get that sound level meter out. Decide what level to mix at and use the meter to help keep mixing at that level. Your ears will thank you, and your mixes will be better for it. 4.
MR8mk2 Protection Circuits There are several protection mechanisms designed into the MR8mk2 to safeguard the loudspeakers and amplifiers from inadvertent damage. CAUTION: The protection circuits are designed to prevent damage to the loudspeakers under reasonable and sensible conditions. Should you choose to ignore the warning signs (i.e., excessive distortion), you can still damage the speakers in the MR8mk2 by overdriving them. Such damage is beyond the scope of the warranty.
If you think your Mackie product has a problem, please check out the following troubleshooting tips and do your best to confirm the problem. Visit the Support section of our website (www.mackie.com/support) where you will find lots of useful information such as FAQs, and documentation. You may find the answer to the problem without having to send your Mackie product away.
MR8mk2 Repair For warranty service, please refer to the warranty information on page 15. Non-warranty service for Mackie products is available at a factory-authorized service center. To locate your nearest service center, visit www.mackie.com, click “Support” and select “Locate a Service Center.” If you do not have access to our website, please call our Tech Support department at 1-800-898-3211 (normal business hours, Pacific Time), to explain the problem.
XLR Connectors 1/4" TS Phone Plugs and Jacks XLR connectors are used to make balanced connections to the MR5mk2. They are wired as follows, according to standards specified by the AES (Audio Engineering Society). “TS” stands for Tip-Sleeve, the two connections available on a mono 1/4" phone jack or plug. They are used for unbalanced signals. It is okay to connect an unbalanced 1/4" phone plug into the 1/4" TRS phone jack on the MR5mk2.
MR8mk2 Appendix C: Technical Information MR8mk2 Specifications Acoustic Performance AC Power Requirements Free Field Frequency Response: 40 Hz – 20 kHz US: Europe: Korea: Japan: Sound Pressure Level @ 1 meter, +4 dBu into Balanced Input: 107 dB SPL @ 1m Maximum SPL Per Pair: 119 dB SPL @ 1m Transducers Low Frequency: 8.
RCA UNBALANCED LINE INPUT XLR BALANCED LINE INPUT HI-FREQUENCY POWER AMPLIFIER HIGH FREQ 1 CROSSOVER +2 dB 0 –2 dB 2 3 INPUT LEVEL +HI VDC HI-FREQ HI-FREQUENCY DRIVER TWEETER LO-FREQ 1/4" UNBALANCED LINE INPUT –HI VDC OVEREXCURSION PROTECT 44 Hz DARK SIDE OF THE MOON LO-FREQUENCY POWER AMPLIFIER LOW FREQ +HI VDC +4 dB +2 dB 0 LO-FREQUENCY DRIVER Owner’s Manual MR8mk2 Block Diagram WOOFER –HI VDC FUSE POWER POWER LED + HI VDC – TOROIDAL POWER TRANSFORMER + LO VDC – The following a
MR8mk2 AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR THE U.S. AND ICES-003, FOR CANADA.
Please keep your sales receipt in a safe place. This Limited Product Warranty (“Product Warranty”) is provided by LOUD Technologies Inc. (“LOUD”) and is applicable to products purchased in the United States or Canada through a LOUD-authorized reseller or dealer. The Product Warranty will not extend to anyone other than the original purchaser of the product (hereinafter, “Customer,” “you” or “your”). For products purchased outside the U.S. or Canada, please visit www.mackie.
220 Wood-Red Road NE • Woodinville, WA 98072 • USA United States and Canada: 800.898.3211 Europe, Asia, Central and South America: 425.487.4333 Middle East and Africa: 31.20.654.4000 Fax: 425.487.4337 • www.mackie.com E-mail: sales@mackie.
