TS / TRS TS / TRS OWNER’S MANUAL MIDI 1 2 3 4 5 MIDI BANANA / CONTINUITY XLR SPEAKON 3.5mm TRS XLR 3.
MTest-1 Cable Tester Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Important Safety Instructions.........................................2 Contents............................................................................3 Features.............................................................................3 Introduction......................................................................3 How To Use This Manual..................................................3 Getting Started.................................................................3 Things To Remember.........
NEWS SCHEDULE TIRE PRESSURE BANANA / CONTINUITY MIDI 1 8 2 3 4 1/8" (3.5mm) TRS and TS 5 2 4 BATTERY CHECK 6 3.5mm TRS 3 3.5mm TRS Attach one end of the cable into the 1/8" (3.5mm) jack and the other end into the other 1/8" (3.5mm) jack. 7 XLR RCA / PHONO GROUND 7 The top panel of the MTest-1 contains the following input jacks: TS / TRS SANITY MIDI TS / TRS THE SCORE FRIDGE 3.
TS / TS / 2 3 4 MIDI 5 RCA / PHONO 1 BATTERY CHECK 3.5mm TRS 3.5mm TRS GROUNDThe top row illuminates yellow and reflects RCA / Phono XLR (M / F) RCA / PHONO Speakon XLR the pin position of the connector on the right side of the MTest-1. Below that is a row of green BATTERY LEDs. These illuminate to reflect the pin position ofCHECK the connector on the left side of the MTest-1. An illuminated pair of LEDs indicate that the corresponding pins are connected correctly. TESTER 3.5mm TRS pinCABLE 3.
MTest-1 Cable Tester Appendix A: Service Information If you think your MTest-1 Cable Tester has a problem, please check out the following troubleshooting tips and do your best to confirm the problem. Visit the Support section of our website (www.mackie.com/support) where you will find lots of useful information such as FAQs and other documentation. You may find the answer to the problem without having to part with your MTest-1 Cable Tester.
MTest-1 Cable Tester Specifications Input / Output Input / Output Type Physical Properties 1/4" TRS / TS Female Bal – Unbal 1/8" TRS / TS Female Bal – Unbal XLR Female Bal – Unbal XLR Male Bal – Unbal RCA / Phono Female Bal – Unbal Speakon Female Bal – Unbal MIDI Female Bal – Unbal Banana / Continuity Female Bal – Unbal 9V Battery Disclaimer The “Running Man” figure is a registered trademark of LOUD Audio, LLC.
MTest-1 Cable Tester MTest-1 Cable Tester Block Diagram FIXED RESISTANCE G Y FIXED RESISTANCE TRS-JACK A G TRS-JACK B Y FIXED RESISTANCE 1 2 3 G Y FIXED RESISTANCE K1 G Y 6 5 4 DIN A FIXED RESISTANCE DIN B G Y FIXED RESISTANCE Phono A Phono B FIXED RESISTANCE R GND 1 3 2 2 XLR/M BUZ1 2- 2+ 1+ 3 1 XLR/F 1- 2- SPEAKON 2+ 1+ 1- SPEAKON FIXED RESISTANCE Y BANANA-R BATTERY 8 MTest-1 Cable Tester BANANA-B 9V G
Please keep your sales receipt in a safe place. This Limited Product Warranty (“Product Warranty”) is provided by LOUD Audio, LLC (“LOUD”) and is applicable to products purchased in the United States or Canada through a LOUD-authorized reseller or dealer. The Product Warranty will not extend to anyone other than the original purchaser of the product (hereinafter, “Customer,” “you” or “your”). Owner’s Manual Limited Warranty For products purchased outside the U.S. or Canada, please visit www.mackie.
16220 Wood-Red Road NE Woodinville, WA 98072 • USA Phone: 425.487.4333 Toll-free: 800.898.3211 Fax: 425.487.4337 www.mackie.
