Specifications

DV 15 - SCSI Termination Page: 2
Basically, if a majority of the data lines change state at once, there is a sudden drain on the TPWR line, which is
resistively coupled to all of the lines, including the /REQ line. This sudden drain causes a spike in the line, and this spike
is propagated into the /REQ line and to the SCSI controller chip. The newer SCSI controller chip in the Macintosh IIfx
interprets this spike as a /REQ signal and starts reading data from the data lines; however, since the data lines need 55 ns
to settle, the data that the controller chip reads is junk.
All internal hard disk drives sold by Apple with the Macintosh IIfx and later machines have the Internal SCSI Filter
installed; however, most third-party drives do not yet have this filter installed and must be modified by a qualified
service provider to work correctly with the Macintosh IIfx.
Back to top
How to Stop the Terminator
Since the problem is caused by a drop in the TPWR line, the fix is to smooth out the line. One need only add a 2.2 uF
capacitor and a 0.01 uF ceramic capacitor as illustrated in Figure 2. These capacitors act like a battery and provide a
little extra current when it is needed. This extra current results in a smoother signal, which the SCSI controller chip does
not interpret as a /REQ signal.
Figure 2 - New-Style Terminator (Black)
This new type of filter is only for internal hard disk drives. The Macintosh IIfx ships with a new and improved external
terminator (black in color), so hard drive manufacturers do not need to worry about external termination. Apple also
ships an internal filter with every Macintosh IIfx that handles the capacitance problem. This internal terminator has two
parts. The first is the resistors for the terminator. This part should already be installed on all internal hard disk drives,
so it is used only for CPUs that do not have an internal hard drive. The second part of the internal terminator is the
capacitor filter. This filter should be installed on the hard disk drive end of the SCSI internal cable. If your hard drive
implements the new capacitors, you can, and should, install the capacitor filter--you cannot have too much capacitance.
Back to top
External Termination
If you manufacture an external SCSI device, do not include termination in it. The only terminator that should be outside a
Macintosh IIfx is Apple's external terminator, and it should be at the end of the SCSI chain. If you make a SCSI terminator,
it is most likely incompatible and may cause damage to the hardware or the data. If your SCSI device cannot connect with
Apple's terminator, then you should provide an adapter that allows your SCSI device to attach to the provided terminator.
Note: A notice in the Macintosh IIfx finished goods box instructs customers to return self-terminating SCSI devices to the
service provider to disable termination.
Back to top
You're Terminated
Not every Macintosh IIfx owner is likely to experience this inconvenience, but a few will. If your customers report
problems that appear to be termination related, then the first possible solution is to fix the terminator (for external
devices) or implement the filter (for internal devices). If you manufacture an external SCSI device that is
self-terminating, you should remove it. This incompatibility will continue with future hardware products and could even
surface on the Macintosh IIci.
Back to top
Macintosh Quadra Termination
Proper SCSI termination is critical for correct operation of the Macintosh Quadra computers, just as with all Macintosh
computers. The Macintosh Quadra computers require external SCSI termination at the end of the device chain, either
supplied by the last device in the chain, or using a standard Apple SCSI Cable Terminator (M0332LL/A). Note that this is
the standard SCSI terminator, notthe black terminator required by the Macintosh IIfx (although the black IIfx terminator
may be used as well).
Termination is generally supplied at the factory for use with internal SCSI devices. Some early floppy-only Macintosh
Quadra 700 units may not have internal termination, so users who attach external SCSI devices (without having added an
internal SCSI device) may need to double terminate their external SCSI chain. Properly terminated floppy-only Macintosh
Quadra 700 units will have a terminator inserted into the motherboard internal SCSI cable connector. Users of internal
SCSI devices must, of course, remove this terminator before connecting their internal SCSI device.
The Macintosh Quadra 900 is the first Macintosh computer to provide a separate, internal SCSI bus. This bus is physically
isolated from the external SCSI bus and must also be properly terminated. The cable provided with the machine includes
all the termination necessary, so all internal devices must have SCSI termination removed before connecting to the
internal Macintosh Quadra 900 SCSI cable. If extra termination is supplied it may cause intermittent hardware failures as
well as physical damage to the device.
Developers who ship terminated SCSI devices for possible internal use in the Macintosh Quadra 900 must provide users
with instructions for removing the termination.
Back to top
PowerBook Termination