M M A C H I N E P A I N T B A L L .
TABLE OF CONTENTS SAFETY INSTRUCTIONS MARKER OVERVIEW OLED BOARD FUNCTIONS HIGH PRESSURE REGULATOR ASA ON/OFF BOLT ASSEMBLY WARRANTY 3–4 5 6–12 13–15 16–17 18–19 20–21 INCLUDED WITH YOUR VAPOR • 2 VAPOR TRIGGERS • BARREL BACKS .685 .689 .693 .697 • BARREL TIP 14” • DOW 33 LUBE • ALLEN KEYS • SPARE O RINGS, SPARE DETENTS • CLAM SHELL CASE TECH SUPPORT TECH@MACHINEPAINTBALL.COM M A C H I N E P A I N T B A L L .
SAFETY INSTRUCTIONS WARNING • • • • • • • • • • • • • • M A C H I N E P A THE MACHINE VAPOR IS NOT A TOY. CARELESS OR IMPROPER USE, INCLUDING FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS WITHIN THIS OPERATOR MANUAL AND ATTACHED TO THE MACHINE VAPOR COULD CAUSE DEATH OR SERIOUS INJURY. DO NOT REMOVE OR DEFACE ANY WARNINGS ATTACHED TO THE MACHINE VAPOR.
SAFETY INSTRUCTIONS WARNING • • • • • • • • • • M A C H I N E P A NEVER LOOK INTO THE BARREL OR BREECH AREA OF THE MACHINE VAPOR WHILE THE MARKER IS SWITCHED ON AND ABLE TO FIRE. NEVER PUT YOUR FINGER OR ANY FOREIGN OBJECTS INTO THE MACHINE VAPOR OTHER THAN PAINTBALLS. NEVER ALLOW PRESSURIZED GAS TO COME INTO CONTACT WITH ANY PART OF YOUR BODY. ALWAYS SWITCH OFF THE MACHINE VAPOR WHEN NOT IN USE. ALWAYS USE A BARREL BLOCKING DEVICE WHEN THE MACHINE VAPOR NOT IN USE.
MARKER OVERVIEW 2 1 4 3 5 6 M A C H I N E P A I N T B A 7 L L . C O M VAPOR BASICS 1. QUICK RELEASE BOLT SYSTEM 2. FEED CLAMP LEVER 3. INTEGRATED GAS THROUGH REGULATOR 4. LATCHING EYE COVERS 5. CUSTOM GEN 4 OLED 6. VENTING CAM ASA 7.
OLED BOARD FUNCTIONS M A C H I N E P A I N T B A L L .
OLED BOARD FUNCTIONS APE GEN 4 OLED BOARD FUNCTIONS TURNING YOUR MACHINE VAPOR ON HOLD THE POWER BUTTON UNTIL THE MACHINE LOGO APPEARS ON THE DISPLAY. AFTER A SHORT DELAY, THE HOME SCREEN IS DISPLAYED; AT THIS POINT THE MARKER IS POWERED ON AND READY TO FIRE. TURNING YOUR MACHINE VAPOR OFF HOLD THE POWER BUTTON UNTIL THE OLED SCREEN STARTS TO FLICKER. THE MARKER WILL SHUT DOWN WHEN THIS FUNCTION IS SELECTED.
OLED BOARD FUNCTIONS IF YOU DO NEED TO TURN THE EYES OFF, PRESS THE YELLOW BUTTON (WHILST IN THE HOME SCREEN) UNTIL THE EYE STATUS INDICATOR CHANGES TO SHOW THAT THE EYES ARE DISABLED. WHEN THE EYES ARE OFF, THE RATE OF FIRE IS LIMITED BY THE EYE OFF ROF SETTING, AND THE EYES ARE NOT USED TO CONTROL THE FIRING CYCLE OR TO PREVENT THE MARKER FROM FIRING. TO TURN THE EYES BACK ON AGAIN, PRESS THE YELLOW BUTTON ONCE AGAIN AND THE INDICATOR WILL SHOW THAT THE EYES ARE ON.
OLED BOARD FUNCTIONS FUNCTION DESCRIPTIONS NOTE: DEPENDING ON THE SOFTWARE VERSION RUNNING ON YOUR MARKER, SOME OPTIONS MAY BE DIFFERENT. SEE THE DOCUMENTATION ACCOMPANYING THE SOFTWARE RELEASE FOR FURTHER INFORMATION. M A C H I N E P POWER OFF SWITCHES OFF THE MARKER, TO PREVENT UNWANTED FIRING AND STOP THE BATTERY FROM BEING DRAINED. FIRE MODE ENTERS THE MENU CONTAINING SETTINGS AFFECTING HOW THE MARKER FIRES.
OLED BOARD FUNCTIONS M A C H I N E P MAX ROF SETS THE MAXIMUM RATE OF FIRE OF THE MARKER. WHEN THE ROF CAP IS IN EFFECT (OR THE EYES ARE NOT IN USE), THE MARKER WILL NEVER FIRE FASTER THAN THIS RATE. ROF CAP SETS WHETHER THE RATE OF FIRE IS CAPPED ACCORDING TO THE MAX ROF SETTING. IF THIS IS OFF, THEN THE MARKER WILL FIRE AS FAST AS THE LOADER CAN FEED IT, AS LONG AS THE EYES ARE IN USE.
OLED BOARD FUNCTIONS DWELL SETS THE LENGTH OF TIME THE SOLENOID VALVE IS HELD OPEN TO ACTUATE THE FIRING CYCLE. IF SET TOO LOW, SHOT VELOCITY WILL BE LOW OR INCONSISTENT, OR THE MARKER MAY NOT CYCLE FULLY; IF SET TOO HIGH THEN AIR EFFICIENCY WILL SUFFER. DEBOUNCE SETS THE LENGTH OF TIME THAT MUST PASS AFTER THE TRIGGER IS RELEASED BEFORE ANOTHER TRIGGER PULL MAY BE REGISTERED.
OLED BOARD FUNCTIONS M A C H I N E P FSDO TIME ALLOWS AN OPTION TO INCREASE THE DWELL ON THE FIRST SHOT AFTER AN IDLE PERIOD. THIS CAN BE USEFUL PARTICULARLY IN VERY COLD CONDITIONS, OR IF THE MARKER’S INTERNALS ARE IN NEED OF SERVICING, AND THE FIRST SHOT AFTER AN IDLE PERIOD IS AT A LOWER VELOCITY (“FIRST SHOT DROP OFF”). IF REDUCED TO ZERO, THIS OPTION IS DISABLED; OTHERWISE THE SETTING DETERMINES HOW LONG MUST PASS WITHOUT A SHOT BEFORE THE NEXT SHOT IS CORRECTED.
HIGH PRESSURE REGULATOR M A C H I N E P A I N T B A L L .
HIGH PRESSURE REGULATOR 7.8x1.9bu/70 13.8x1.9bu/70 17x2 bu/70 5x2 bu/70 #14 bu/70 #14 bu/70 THE VAPOR HIGH PRESSURE REGULATOR (HPR) HAS A OPERATING RANGE FROM 150-190 PSI.THE HPR IS FACTORY SET TO 180 PSI. INCREASE PRESSURE TURN THE ADJUSTER TO THE RIGHT. DECREASE PRESSURE TURN THE ADJUSTER TO THE LEFT. #14 pu/70 #9 pu/70 #14 bu/70 #17 bu/70 #6 pu/70 #6 pu/70 M A C H I N E P A I N T B A L L .
HIGH PRESSURE REGULATOR MAINTAINING THE INLINE REGULATOR YOUR INLINE REGULATOR, REGULATES THE PRESSURE FROM YOUR AIR SYSTEM DOWN TO THE PRESSURE USED TO FIRE YOUR VAPOR. IT IS VERY IMPORTANT THAT YOUR INLINE REGULATOR IS WORKING WELL. IF NOT, YOU MAY EXPERIENCE PROBLEMS WITH VELOCITY FLUCTUATION OR SHOOTDOWN. BEFORE WORKING ON YOUR REGULATOR, MAKE CERTAIN THAT THE AIR SUPPLY IS TURNED OFF, AND SAFELY FIRE ANY GAS OUT OF THE GUN TO ENSURE IT DOES NOT HAVE ANY RESIDUAL PRESSURE, THEN REMOVE THE GAS SOURCE.
ASA ON/OFF M A C H I N E P A I N T B A L L .
ASA ON/OFF ATTACHING BOTTLE MUST USE A LOW PRESSURE AIR SYSTEM. CAREFULLY SCREW YOUR AIR SYSTEM INTO THE ASA UNTIL IT STOPS. WHEN SCREWING YOUR AIR SYSTEM INTO THE ASA, THE THREADS SHOULD BE LOOSE. IF AT ANY POINT THEY BECOME TIGHT, DO NOT FORCE THE THREADS, THIS MAY CAUSE DAMAGE TO YOUR AIR SYSTEM OR YOUR MARKER. M A C H I N E P GAS UP VAPOR TURN THE ASA LEVER TO THE CENTER POSITION. YOU WILL HEAR YOUR VAPOR ENERGIZE.
BOLT ASSEMBLY M A C H I N E P A I N T B A L L .
BOLT ASSEMBLY 7.8X1.9BU/70 9X1.5BU/70 9X1BU/70 9X1BU/70 #13 PU /70 #13 PU/70 #17BU/70 #17BU/70 #17BU/70 #17BU/70 #17BU/70 #17PU/70 #16 PU/50 #14 BU/70 #15BU/90 #17BU/70 #17BU/70 MAINTAINING THE VAPOR BOLT ASSEMBLY YOUR BOLT SYSTEM SHOULD BE MAINTAINED AFTER EVERY 8,000 SHOTS. YOU MAY MAINTAIN YOUR BOLT SYSTEM MORE FREQUENTLY SHOULD YOU FEEL THE NEED. BEFORE WORKING ON YOUR BOLT SYSTEM, ENSURE THAT YOUR VAPOR IS DE-GASSED, THEN PUSH THE BOLT RELEASE ROTATE THE BOLT AND PULL OUT OF THE MARKER.
WARRANTY MACHINE PAINTBALL WARRANTS FOR 2 YEARS TO THE PURCHASER, FROM THE INITIAL DATE OF PURCHASE, THAT THE PAINTBALL MARKER AND REGULATOR ARE FREE FROM DEFECTS IN MATERIALS AND WORKMANSHIP, SUBJECT TO THE REQUIREMENTS, DISCLAIMERS AND LIMITATIONS OF THIS WARRANTY. DISPOSABLE PARTS, NORMAL MAINTENANCE AND STANDARD WEAR AND TEAR PARTS SUCH AS BATTERIES, O-RINGS AND SEALS ARE NOT WARRANTED. THE SOLENOID AND ELECTRONIC COMPONENTS ON THE MARKER ARE WARRANTED FOR 2 YEARS.
WARRANTY • DIAGNOSTIC SERVICE, REPAIR & TUNE: $25.00 (NON REFUNDABLE) (DIAGNOSE, REPAIR, O RING, LUBE & REPLACEMENT, TESTING FUNCTIONS, COMPLETE TUNING AND SETTING ALL PRESSURES TO MANUFACTURES SPECS.) • PARTS UPGRADES/REPLACEMENT: COST OF PARTS (INSTALLATION INCLUDED IN COST OF SERVICE & REPAIR) • WARRANTY REPAIR: WILL BE FILED UNDER MANUFACTURER’S WARRANTY ON ANY MARKER THAT IS WITHIN THE 2 YEARS FROM DATE OF PURCHASE.
