User`s guide

i.MX53 System Development User’s Guide, Rev. 1
Freescale Semiconductor A-3
Appendix A
Revision History
Table A-1 provides a revision history for this user guide.
Table A-1. i.MX53 System Development User Guide Document Revision History
Rev.
Number
Date Substantive Change(s)
Rev 1 3/2011 • In Table 1-1, "Design Checklist," changed “CCR CAMPx_EN” to “CCM_CCR[CAMPx_EN],” under the
recommendation 11 and EMI to EIM under the recommendations 3, 4 and 5.
•In Section 4.2, “IOMUX Tool Walkthrough,” the following introductory text was added to the first
paragraph: “The i.MX35 example shown is for illustration only. The steps in the process apply to all i.MX
products in the preceding bullet list.”
•In Table 5-1, "i.MX53 Voltage Rails and Associated DA9053 Regulator," the following updates were done:
— VDDGP voltages changed from 1.05 to 1.1 and 1.2 to 1.25
— NVCC_LCD changed from 1.87 to 1.8 and 2.77 to 2.775
— NVCC_NANDF changed from 1.87 to 1.8
— TVDAC_DHVDD changed from 2.75 to 2.775, 1.87 to 1.8, and 2.77 to 2.775
— NVCC_RESET changed from 1.87 to 1.8 and 2.77 to 2.775
— VDD_REG changed from 1.6 to 2.475
•In Table 5-2, "i.MX53 Voltage Rails and Associated LTC3589-1 Regulator," the following updates were
done:
— VDDGP voltages changed from 1.05 to 1.1 and 1.2 to 1.25
— NVCC_LCD changed from 1.87 to 1.8 and 2.77 to 2.775
— NVCC_NANDF changed from 1.87 to 1.8
— TVDAC_DHVDD changed from 1.87 to 1.8 and 2.77 to 2.775
— NVCC_RESET changed from 1.87 to 1.8 and 2.77 to 2.775
•In Table 5-2, "i.MX53 Voltage Rails and Associated LTC3589-1 Regulator," the Current Capability for
VCC, NVCC_LVDS, USB_H1_VDDA25, VDD_REG, and VPH changed from 1000 to 1200.
•In Table 5-2, "i.MX53 Voltage Rails and Associated LTC3589-1 Regulator," changed Fusebox to
FUSEBOX, S-ATA to SATA, and in the table’s introduction, changed i.MX to i.MX53.
•In Table 8-1, "Clock Roots," changed all the block mnemonics to upper case in the Description column.
•In Table 8-1, "Clock Roots," changed LVDS to LDB.
•In Section 10.2.6, “SD/MMC Test,” changed SDHC3 to ESDHCV3-3 and SDHC2 to ESDHCV2-2.
•In Section 11.3.1, “Changing the DCD Table for i.MX53 DDR3 Initialization,” changed ESDCTLv2.5 to
ESDCTL.
•In Chapter 13, “Configuring the IOMUX Controller (IOMUXC), changed “IOMUX Controller” to IOMUXC.
•In Chapter 15, “Adding Support for the i.MX53 ESDHC,” changed “eSDHC1/2/3/4” to “ESDHCV2-1/2/4
and ESDHCV3-3.”
• Changed eCSPI to ECSPI and eSDHC to ESDHC, throughout the document.
•In Section 15.3.3, “Interface Layouts,” changed i.MX35 to i.MX53 in the title and description of
Figure 15-2.
•In Figure 18-2, replaced MCIMX53 with i.MX53.
•In Section 20.7.1, “CMOS Interfaces Supported by the i.MX53,” replaced the term IPUv3M with IPU.
• Replaced the term IPUv3M with IPU in Figure 20-1, Figure 20-5, Figure 18-1, Figure 18-4, and
Section 18.5, “i.MX53 Display Interface Helpful Information.”
•In Table 20-3, "CSI0 Parallel Interface Signals," changed the column heading “IPUv3 Pin” to “IPU Pin.”
•In Section 21.1, “Common Porting Task,” replaced AUDIOMUX with AUDMUX.
Rev 0 02/201
1
Initial release.