B SERIES SELF PROPELLED WINDROWERS
TABLE OF CONTENTS SP85B, SP115B, SP185B SP WINDROWERS- DHW, AHB, DKHB HEADERS FEATURES AND BENEFITS SP85B, SP115B, SP185B Tractor Introduction...................................................................................................1 New Features ..........................................................................................2 SP85B, SP115B, SP185B Comparison Chart .........................................4 Market............................................................................
TABLE OF CONTENTS SP85B, SP115B, SP185B SP WINDROWERS- DHW, AHB, DKHB HEADERS FEATURES AND BENEFITS (CONT) AHB AUGER HEADER Introduction.................................................................................................48 Auger Header Sizes ...................................................................................49 Cutterbar ....................................................................................................50 Reel .....................................................
TABLE OF CONTENTS SP85B, SP115B, SP185B SP WINDROWERS- DHW, AHB, DKHB HEADERS SPECIFICATIONS SP85B SP Windrower .....................................................................................78 SP115B SP Windrower ...................................................................................81 SP185B SP Windrower ...................................................................................84 AHB Auger Header ...................................................................................
FEATURES AND BENEFITS B SERIES SP WINDROWER INTRODUCTION The Challenger SP85B, SP115B, and SP185B replace the original Challenger SP80, SP110 and SP165 windrowers. The new machines bring upgraded Tier II engines (which meet all government emissions standards, along with improved performance), a new hydraulic system, for increased reliability and lower noise levels, and it is now easier to adapt both auger and draper headers to all of the windrower tractors.
FEATURES AND BENEFITS B SERIES SP WINDROWER SP85B and SP115B SP Windrower The Challenger SP85B replaces the SP80 windrower, and the SP115B replaces the SP110.
FEATURES AND BENEFITS B SERIES SP WINDROWER SP185B SP Windrower The Challenger SP185B replaces the SP165 windrower.
FEATURES AND BENEFITS B SERIES SP WINDROWER Specification Differences between SP85B, SP115B, and SP185B SP85B SP115B SP185B 85 hp 1 speed Planetary 18.4 x 26 16.9 x 28 18.4R26 14L x 16.1 12.5L x 15 60 gal Opt Std Std 115 hp 2 speed Planetary 18.4 x 26 16.9 x 28 18.4R26 14L x 16.1 12.5L x 15 60 gal Std Std Std 185 hp 2 speed Planetary 23.1 x 26 18.4 x 28 NA 14L x 16.
FEATURES AND BENEFITS B SERIES SP WINDROWER MARKET The SP185B is designed to work with the DKHB disc header, the DHW draper header, and the AHB auger header. The SP185B is for the operator who is looking for higher windrower capacity. It is ideal for the custom operator, large rancher, or operator with a large dairy or cow-calf operation. The SP185B is intended for the operator who has to put up large volumes of hay on a timely basis.
FEATURES AND BENEFITS B SERIES SP WINDROWER MAJOR COMPETITORS Challenger ............................................ SP185B New Holland .......................................... HW345 (Non Current) ........................................ HW340 John Deere ................................................ 4995 Case-IH ............................................. WDX1902 (Non Current) .................................... WDX1701 Challenger ............................................ SP115B New Holland ....
FEATURES AND BENEFITS B SERIES SP WINDROWER CHASSIS Long Wheelbase The tractor has a wheelbase of approximately 140” (3.57 m). The long wheelbase helps smooth the ride in rough fields, even at high ground speeds. The smooth ride adds to operator comfort allowing the operator to run longer and get more done. Wheelbase Frame The SP185B frame is heavier than the SP165, as it uses 1/4” welded box beams in the side rails.
FEATURES AND BENEFITS B SERIES SP WINDROWER Engine Compartment Access A tilting hood allows the operator to easily access the engine compartment. The hood can open to two positions. The hood is lifted to the first latch position for daily service. The hood can then be moved to a wide-open position for periodic servicing, such as changing the air cleaner. The tilting hood allows improved access for quicker and easier maintenance, and less downtime.
FEATURES AND BENEFITS B SERIES SP WINDROWER Lift Arms (SP85B, SP115B) The lower lift arm anchor, lift arm struts, and lift arms have been strengthened to accommodate both auger and draper headers. Lift Arm receivers (SP185B Only) The lift arm receivers make it easier for disc, sickle, or draper headers to be attached to the SP185B tractor. Large Drive Tires The 18.4 x 26 turf and 16.9 x 28 bar tread (SP85B, SP115B) high flotation tires provide a long, wide footprint. The SP185B uses a 23.
FEATURES AND BENEFITS B SERIES SP WINDROWER Rear Tires The 14L x 16.1 high flotation rear tires allow the tractors to glide over the roughest terrain, under the most adverse conditions. The high flotation tires provide the smoothest ride possible, for less operator fatigue. Adjustable Walking Beam Axle The walking beam can be set for tread widths of 84.4 in (2144 mm), 102.2 in (2596 mm), or 120 in (3048 mm). The adjustable rear-walking beam provides excellent tracking if used in row crop applications.
FEATURES AND BENEFITS B SERIES SP WINDROWER GROUND DRIVE & HYDRAULIC SYSTEM Hydraulic System The new hydraulic system uses renowned Sauer-Danfoss components. The new system will provide more reliability, and reduced sound levels. The hydraulic components are built heavier to handle higher horsepower. Tandem Pumps Wheel Motors The wheel motors are now attached directly to the planetary drive, eliminating the chain drive.
FEATURES AND BENEFITS B SERIES SP WINDROWER Step-Up Gearbox (SP185B Only) A step-up gearbox (1.33:1) is used on the tandem ground drive pumps. The higher pump speed allows the use of a lower gear ratio planetary, for better torque in low range, and better handling. The higher ground drive pump speed allows a faster low range (12 mph, 19 km/hr), and a fast high range (16 mph, 25 km/hr). Step Up Gearbox Hydraulic Parking Brake (SP115B, SP185B) The parking brake is now applied more positively.
FEATURES AND BENEFITS B SERIES SP WINDROWER Header Drive The header drive speed is set depending on the header installed. When the electrical wire from the header to the tractor is connected, the tractor will know what header is attached, and the hydraulic flow to the header is automatically adjusted. For example, a draper header runs slower therefore requires less hydraulic flow than a disc header.
FEATURES AND BENEFITS B SERIES SP WINDROWER Worm Gear Steering Drive The worm gear steering gives the operator precise steering control. The movement of the steering wheel closely resembles actual tractor movement. The steering wheel movement in the field is reduced, and steering action on the road is more predictable. The worm gears are enclosed, containing lubrication and reducing wear. The operator can keep better control of the machine at high field and road speeds with less effort, reducing fatigue.
FEATURES AND BENEFITS B SERIES SP WINDROWER ELECTRICAL SYSTEM Alternator The SP115B and SP85B tractors are equipped with a 110 amp alternator. The SP185B has a 95 amp alternator. The alternator is large enough to handle nighttime cutting, which requires operating lights, as well as heater or air conditioner, for operator comfort. The alternator is sized for large electrical loads, for more reliable operation. Alternator SP85B Batteries The windrower tractor is equipped with two 12volt batteries.
FEATURES AND BENEFITS B SERIES SP WINDROWER External Battery Booster Posts Challenger windrowers are equipped with external battery booster posts. These posts are located on the left side of the engine main frame. The posts eliminate the need to raise the hood when jumping the windrower, or provide a handy place to attach cables to jump another vehicle. The booster posts are easily accessible for convenient use of jumper cables.
FEATURES AND BENEFITS B SERIES SP WINDROWER ENGINE AND ACCESSORIES Engines The new Challenger windrower engines meet all Tier II emissions standards. ♦ The SP185B engine is a 185 hp, 5.9 liter, turbocharged and intercooled Cummins QSB 185A engine. ♦ The SP115B engine is a 115 hp, 4.41 liter, Direct Injection Turbocharged Caterpillar 3054E engine. ♦ The SP85B engine is a 85 hp, 4.41 liter, Direct Injection Naturally Aspirated Caterpillar 3054C engine.
FEATURES AND BENEFITS B SERIES SP WINDROWER Fuel Tank The SP85B and SP115B tractors are equipped with a 60-U.S. gallon fuel tank (227 L). The SP185B has an 80 gallon (303 L) capacity. The large tanks provide enough fuel for 10 hours of field operation. The fuel tank is easily accessed by use of the service platform and folding ladder. The large fuel tank allows the machine to run longer without refueling, increasing productivity.
FEATURES AND BENEFITS B SERIES SP WINDROWER CAB Cab Design The cab is designed for maximum operator comfort. Special attention was paid in placing all controls and monitoring systems in the most convenient position for the operator. The cab allows the operator to work at peak productivity for much longer, increasing total output. All headers feature a header walkway, and the cab features grab rails to hold on to, making it easy to clean the cab glass.
FEATURES AND BENEFITS B SERIES SP WINDROWER Air Suspension Seat The operator’s seat is air suspended to absorb the shocks of high speed mowing on rough fields. The SP115B and SP185B seat have a three position adjustable vertical shock absorber. The seat can be held stationary or set for isolator. The isolator allows the seat to move fore and aft with the operator to absorb shocks and reduce operator fatigue when operating on rough terrain. The left armrest tilts back for easy entrance/ exit.
FEATURES AND BENEFITS B SERIES SP WINDROWER Console Gauges The console gauge cluster includes water temperature (1), voltmeter (2), oil pressure (3), fuel gauge (4), speedometer (5), and hourmeter (6). The console also monitors hydraulic oil level (7), coolant level (8), hydraulic oil pressure (9), and air cleaner restriction (10) and has a turn signal/flasher indicator lamp (11). A performance monitor is standard equipment on the SP185B and offered as an optional kit for the SP85B and the SP115B.
FEATURES AND BENEFITS B SERIES SP WINDROWER Monitor (Standard on SP185B, Optional on SP115B and SP85B) The electronic monitor checks 6 different functions on the windrower. The monitor graphically shows engine RPM with the bar graph along the top of the LCD. The digital display shows one of 6 different functions. From left to right the functions are, ground speed [4], header speed [5], engine RPM’s [6], cutting rate (acres/hour) [7], area cut (re-settable) [8], and total area cut [9].
FEATURES AND BENEFITS B SERIES SP WINDROWER Engine Indicator Lights (SP185B, SP115B) A new row of indicator lights has been added under the monitor on the SP185B tractor. The lights are Engine Stop (stop engine immediately), Engine Warning (service engine soon), Wait to Start (used with engine intake air heater), Water in Fuel, and Engine Service (low fluid level).
FEATURES AND BENEFITS B SERIES SP WINDROWER Ground Speed and Header Control Lever The Ground Speed and Header Control Lever utilizes the same ergonomically designed handle as the Challenger combines. The lever is designed to support the operator’s hand in the most comfortable position. The operation of the lever is very smooth and easy, as the operation is servo-assisted.
FEATURES AND BENEFITS B SERIES SP WINDROWER Air Conditioner and Heater The cab is fitted with a high capacity air conditioner to keep the operator environment cool on the hottest days. A heater is also standard to make the machine versatile for all seasons. The cab is equipped with four vent outlets, and two re-circulation vents. The vents can be directed toward the windshield to defog, or towards the operator for maximum comfort.
FEATURES AND BENEFITS B SERIES SP WINDROWER Rear View Mirrors The cab is equipped with a deluxe mirror located on each side of the cab, plus a mirror inside the cab. They provide the operator with an excellent view of cut and uncut crop. The mirrors also are invaluable when roading the machine to monitor traffic. The large mirrors allow the operator to monitor the rear, both in the field and on the road, improving productivity and operator security.
FEATURES AND BENEFITS B SERIES SP WINDROWER Control Console Position Adjustment The fore-aft location of the control console can be adjusted relative to the operator’s seat by using two adjustment knobs located under the console. The console can also be moved to one of four vertical positions relative to the operator’s seat, by utilizing a retaining knob at the rear of the console. The console can be adjusted relative to the operator, for greater operator comfort.
FEATURES AND BENEFITS B SERIES SP WINDROWER OPTIONAL KITS (FIELD INSTALLED) Windshield Wiper Kit The windshield wiper kit includes the wiper blade, arm, linkage, electric motor, switch, and all hardware needed to mount on the cab. The wiper kit improves visibility when raining, giving the operator greater control during roading. Wholegoods Kit – BK61083 Estimated Installation Time – 2.0 Hr.
FEATURES AND BENEFITS B SERIES SP WINDROWER Weight Carrier Kit (SP185B) The kit consists of a weight carrier bracket on each side of the tractor. The brackets accommodate common tractor suitcase weights. The weight kit is standard on the SP85B and the SP115B tractors. Recommended with DHW Header. Wholegoods kit – BK60945 Estimated Installation Time – 1.0 Hr. Weight Carrier Hitch Kit The hitch kit is used with a draper header to pull a swath roller.
FEATURES AND BENEFITS B SERIES SP WINDROWER Rotary Screen Kit (SP85B Only) The rotary screen provides a large volume of clean air for efficient engine cooling. Leaves and chaff drop off the screen by use of a dead air space, or are whisked off by the action of a screen vacuum. The rotary screen provides clean air to the engine, with less chaff getting into the radiator, for less time spent cleaning. Wholegoods Kit – BK61025 Estimated Installation Time – 3.0 Hr.
FEATURES AND BENEFITS B SERIES SP WINDROWER Performance Monitor (SP85B, SP115B) An optional performance monitor is available. The monitor shows engine rpm all the time. The display can scroll by using the switch on the hydro handle. (Standard Equipment on SP185B) 1) 2) 3) 4) 5) 6) Ground Speed Header Speed Engine rpm Acres/Hour Field Acres Total Acres Performance Monitor Wholegoods Kit – BK61138 Estimated Installation Time – 2.0 Hr.
FEATURES AND BENEFITS B SERIES SP WINDROWER Stereo Radio An AM-FM stereo-cassette player radio or AMFM stereo-cassette with weatherband is available through wholegoods. The radio allows the operator to keep up-to-date on the news, weather, and market reports. The speakers are placed to provide the operator with excellent sound quality. The B series tractors come standard with the speakers, noise suppressor, antenna, and fuse. The wiring is in place to plug the radio in.
FEATURES AND BENEFITS B SERIES SP WINDROWER Double Windrower Attachment (For SP185B Only) The double windrower attachment (DWA) is designed to lay two windrows together, or sideby-side. The first pass through the field deposits a windrow on the right side of the tractor. A right hand turn and a second pass through the field lays the two windrows together, or side-byside. The kit provides everything needed to attach the DWA to the SP185B tractor.
FEATURES AND BENEFITS B SERIES SP WINDROWER DWA Carriage The entire DWA carriage can be raised and lowered with the header. A three position switch in the cab controls the attachment. With the switch in the right position, the draper is on, and the DWA will raise and lower with the header. With the switch in the middle position, the draper is shut off, and the DWA will raise and lower with the header.
FEATURES AND BENEFITS DKHB DISC HEADER DKHB Header INTRODUCTION The DKHB header is the updated disc header that will be used on the SP185B Windrower Tractor. The DKHB is available in a 12’ and a 15’ 3” cut version. The new header shares many of the proven features of the DKH header, along with these improvements: ♦ Header motors are included with the header. This makes it easier to adapt the auger and draper headers to the SP185B tractor. ♦ Redesigned crop conveying cages for smoother crop flow.
FEATURES AND BENEFITS DKHB DISC HEADER CUTTERBAR Gear to Gear Cutterbar Both the 12’ and 15’ 3” cutterbar are a spur gear design. Each gear assembly and adjacent idler gear can be individually removed and serviced, without disassembly of the cutterbar, reducing downtime and increasing productivity. The spur gear design allows the cutterbar profile to be thinner, allowing closer cutting with less scalloping. Cutterbed Cutterbar Gears The cutterbar gears have heavy duty, wide profile teeth.
FEATURES AND BENEFITS DKHB DISC HEADER Sealed Bed Bearings The bed bearings are sealed, which gives several advantages: 1) Bearing life is longer, as any contamination in the bed will not cause bearing failure. Longer bearing life makes for a long life cutterbed, for less machine downtime. 2) The primary lubrication for the bearings is self contained in the sealed bearing. The oil for the bed lubrication is mainly to coat the gear teeth, so the quantity of lubrication required for the bed can be reduced.
FEATURES AND BENEFITS DKHB DISC HEADER HAY CONDITIONER Fully Engaged Conditioner Rolls The crop is crimped by the action of the conditioner rolls cracking the plant stem along it’s entire length. Crop leaves are retained, for higher hay protein content. Conditioner rolls are available from the factory steel on steel only, as it has been found that rubber roll wear is unacceptably high in a high capacity disc mower conditioner.
FEATURES AND BENEFITS DKHB DISC HEADER Conditioner Roll Pressure Release The conditioner rolls utilize an over center cam (1) at each end that allows the rolls to open easier when an obstacle or clump of hay is encountered in the field. The over center cam will automatically reset after the obstruction has passed through the conditioner rolls. The roll pressure release allows the potential plug to expel without stopping, enhancing productivity.
FEATURES AND BENEFITS DKHB DISC HEADER HEADER MAINFRAME Cutterbar Frame The cutterbar is set into a “cradle” which helps keep the cuttebar from twisting. (In the picture to the right, the yellow framework surrounds the black cutterbar.) Flexing causes wear on gear teeth, which can shorten life. Keeping the cutterbar rigid saves downtime by prolonging bed life.
FEATURES AND BENEFITS DKHB DISC HEADER Header Drive The cutterbar is driven by a hydraulic motor on each end of the header. This equalizes the torque load across the entire cutterbar, for longer life. The header speed can be adjusted separately from the engine speed, from 0 to 2600 rpm. The engine speed can be reduced while still maintaining full cutterbar speed, maximizing fuel efficiency.
FEATURES AND BENEFITS DKHB DISC HEADER Swath Shield The swath shield adjustment can be made with minimal effort and no tools. In some high humidity areas, laying out a wide swath cures the crop faster than narrower windrows. The operator can choose the windrow or swath width that is right for a particular area. The swath shield can be set to any position from narrow windrow to full width swath, for greater machine versatility.
FEATURES AND BENEFITS DKHB DISC HEADER Header Walkway A walkway (1) has been built into the header, and made non-slip by adding two friction strips. The header walkway and hand rails (2) on the cab to hold on to, provide improved access to the cab windows, making them easier to clean. Header Walkway Hydraulic Header Tilt The header tilt cylinder regulates the header angle from 0° up to 10°. For normal operation, a 0 to 4° header tilt angle is used.
FEATURES AND BENEFITS DKHB DISC HEADER Hydraulic Header Flotation Header flotation is maintained with a nitrogen charged hydraulic accumulator and hydraulic cylinders installed on the tractor. Flotation can be regulated during operation of the machine with an electric switch located on the tractor’s instrument panel. The hydraulic flotation allows the header float to better match field conditions, prolonging header life.
FEATURES AND BENEFITS DKHB DISC HEADER OPTIONAL KITS (FIELD INSTALLED) Swathboard Actuator Kit The swathboard actuator kit allows the swathboard position to be controlled from the operator’s seat. This allows the operator to change the shape of the swath moving from light to heavy crops without leaving the tractor seat. The kit includes an electric actuator and all hardware for kit installation.
FEATURES AND BENEFITS DKHB DISC HEADER Gauge Wheels The gauge wheels are for use in damp field conditions, where skid shoes tend to build up with mud. They are very useful in first yearseeded fields that are still soft. The gauge wheels can also be adjusted to increase cutting height, which is useful when cutting cane type crops. The gauge wheels do less damage to fields, maximizing future crop production.
FEATURES AND BENEFITS DKHB DISC HEADER SERVICE PARTS Knives Several versions of knives can be ordered through AGCO Service Parts to contend with different crop conditions. The standard knife on the DKHB header is the 18° bottom bevel. Four styles of knives are available: 11° Top Bevel – Provides a good quality of cut in most crops and conditions, but if the knife is deflected down, tends to cut into cutterbed. 11° Combination Bevel – One side is bottom bevel, and the other is top bevel.
FEATURES AND BENEFITS AHB SICKLE HEADER SP115B AHB INTRODUCTION The AHB header replaces the AH header. The new header shares many of the proven features of the AH header, along with these improvements: ♦ Header motors are included with the header. This makes it easier to switch the windrower tractor between the auger and draper header (or between disc, auger, and draper header on the SP185B).
FEATURES AND BENEFITS AHB SICKLE HEADER AUGER HEADER SIZES AHB Double Sickle, Dual Auger Header The following sizes of auger headers are available for the SP85B, SP115B, and SP185B tractors: ♦ 14 foot ♦ 16 foot ♦ 18 foot AHB Field Header Operating Controls All the header operating controls for the headers are located in the tractor cab. The header controls for engaging the header (1) and header flotation (2) are located on the side console.
FEATURES AND BENEFITS AHB SICKLE HEADER CUTTERBAR Lean Bar The purpose of the lean bar is to push the crop forward and down, so that after being cut by the sickle, it will feed through the augers and into the conditioner butt-end first. The lean bar should catch the crop between one-third and one half the crop height. Proper adjustment ensures crop is not fed head first, which will result in greater leaf shatter.
FEATURES AND BENEFITS AHB SICKLE HEADER Guard Angle The header tilt cylinder or turnbuckle (SP85B) regulates the guard angle from 5O up to 12O. For normal operation, a 12O guard angle is used. At this angle, the guards slide under and pick up the crop better. When rocky conditions or uneven ground exist, a lesser degree angle setting can be set to prevent the sickle guards from picking up rocks or digging in so readily. The guard angle can be easily set to optimize header performance in all crop conditions.
FEATURES AND BENEFITS AHB SICKLE HEADER Spare Sickle Storage The AHB auger headers are equipped with storage for spare sickles. This allows the operator to change a worn or damaged sickle in the field. Spare sickles can be stored on the machine, speeding routine maintenance.
FEATURES AND BENEFITS AHB SICKLE HEADER REEL 5 Bat Reel The five bat reel is standard, allowing crop to move to the augers in a smooth and uniform manner. Each reel bat will take a smaller “bite” than a four bat reel, and the conditioner will be fed smoothly. Plugging and bunching at the conditioner roll is minimized. The reel bat spiders are bolted to the bulkheads, so a sixth bat can be installed (available through Service Parts).
FEATURES AND BENEFITS AHB SICKLE HEADER Reel Cam Track The cam track can be adjusted to control the reel tine release of the crop to the augers. This allows a very wide range of crop conditions to be accommodated with minor adjustment. The reel cam track easily adjusts for a wide range of crops and conditions, for increased machine versatility. Cam Track Tine Tube Bearings The tine tube bearings on the AHB header are sealed ball bearings.
FEATURES AND BENEFITS AHB SICKLE HEADER DUAL AUGERS Counter Rotating Dual Augers Dual augers convey crop gentler and smoother than single augers. The reason is because dual augers have two “live” feeding elements (the augers) conveying the crop between them, as opposed to one “live” element (auger), and one “fixed” element (header pan). This provides a smoother transition from the reel to the conditioner rolls, for increased capacity with less hesitation and bunching.
FEATURES AND BENEFITS AHB SICKLE HEADER Removable Auger Pans In conditions with abrasive sand or dirt, the lower header pans can be removed to allow the dirt to fall through and reduce wear on the auger. The removable auger pans help reduce auger wear, extending auger life and reducing maintenance expense. Auger Pans Auger Slip Clutches The augers are slip clutch protected from damage when rocks or other foreign material get into the headers. Each auger has it’s own slip clutch.
FEATURES AND BENEFITS AHB SICKLE HEADER HAY CONDITIONER 110 Inch Conditioner Rolls The 110 inch conditioner rolls are offered as rubber-on-steel or steel-on-steel configurations. Both offer superior crimping conditioning, but the steel-on-steel configuration gives longer life in abrasive soil conditions. The 110 inch wide conditioner rolls are fully engaged, not intermeshed, so the crop is crimped, and not crushed.
FEATURES AND BENEFITS AHB SICKLE HEADER Conditioner Roll Feeding Angle The augers feed the conditioner rolls at a consistent angle. Both auger and conditioner rolls are attached to the header, so head float does not change the angle of the crop entering the conditioner rolls. The consistent feed angle reduces the chance of crop hesitation and bunching, resulting in smoother, quicker drying windrows.
FEATURES AND BENEFITS AHB SICKLE HEADER Conditioner Roll Pressure Release The conditioner rolls utilize an over center cam at each end that allows the rolls to open easier when an obstacle or clump of hay is encountered in the field. The over center cam will automatically reset the rolls after the obstruction has passed through the conditioner rolls. The operator is not required to stop and lift the header, as are competitive designs which open the conditioner rolls as the header is raised.
FEATURES AND BENEFITS AHB SICKLE HEADER HEADER MAINFRAME Forming Shields The side forming shields are non-metallic, reducing crop buildup and enhancing windrow formation. The shields also won’t rust when the machine sits over the winter. The adjustable rear deflector shield slows crop momentum to allow it to fall gently into a tall, fluffy, quick drying windrow. The forming shields and rear deflector can be set to the operator’s preference.
FEATURES AND BENEFITS AHB SICKLE HEADER Skid Shoes Skid shoes can be raised or lowered easily without tools to adapt to different crops or field conditions. The skid shoes can be adjusted for various cutting heights up to five inches. The skid shoes are easily set for maximum operator convenience and crop adaptability. Hydraulic Header Flotation Skid Shoe Flotation can be regulated during operation of the machine from the cab with an electric switch located on the tractor’s instrument panel.
FEATURES AND BENEFITS AHB SICKLE HEADER Header Lift Cylinder Stop To hold the header up in a secured position, a header lift cylinder stop is provided for the lift cylinder. In the up position, the header stop is placed between the lift cylinder and the lift mechanism when the header is raised. In the storage position, the header stop is moved back and held out of the way by a spring assembly.
FEATURES AND BENEFITS AHB SICKLE HEADER OPTIONAL KITS (FIELD INSTALLED) Crop Divider Kit The crop divider kit is designed to divide tall crops, so that the header end panels do not knock down the crop and cause stripping. Lower auger angles are included to help feed tall cane type crops. The operator stays more productive, as by separating the crop before it gets to the header, more crop will be put into the windrow, and less will be knocked down and wasted.
FEATURES AND BENEFITS AHB SICKLE HEADER Hay Conditioner Close-up Kit The hay conditioner close-up kit is used to help move light crop more to the center of the conditioner rolls to help form narrow windrowers. The standard windrow forming shields can be utilized. The kit includes two filler pans to close off 12” on each end of the conditioner rolls. Longer auger strippers are also supplied. Wholegoods Kit – 14’ – BK60928 16’ – BK60929 18’ – BK60930 Estimated Installation Time – 3.0 Hr.
FEATURES AND BENEFITS AHB SICKLE HEADER Swathboard Actuator Kit The swathboard actuator kit allows the operator to change the shape of the swath in light or heavy crops without leaving the tractor seat. The kit includes an electric actuator and all the wiring and hardware needed to attach to the header swathboard. Wholegoods Kit – BK60917 BK61150 actuator adapter also required per Service Bulletin CWR 04-06. Estimated Installation Time – 1.0 Hr.
FEATURES AND BENEFITS DHW DRAPER HEADER DHW Draper Header INTRODUCTION The DHW draper header is available in three sizes of center delivery: 22’, 25’, and 30’. There are also three sizes of Double Swath (shiftable headers: 22’, 25’, and 30’. The DHW header replaces the DH header. The new header shares many of the proven features 0f the DH header, along with these improvements: ♦ Header will mount to SP85B and SP115B tractors without an additional mounting kit.
FEATURES AND BENEFITS DHW DRAPER HEADER CUTTERBAR Cutterbar Profile The cutterbar has been designed for smooth crop flow over the top. The skid plate along the bottom of the cutterbar also gives it the ability to cut close to the ground. Cutterbar Sickle Drive The sickle drive is a hydraulically driven planetary gear system. The planetary gear system is in rotation at all times, so there are no peak starting and stopping loads as in a wobble box system.
FEATURES AND BENEFITS DHW DRAPER HEADER Sickle Over-Stroke The sickle is designed to over-stroke in each direction. The over-stroke ensures that the sickle will travel its full length of stroke, especially in a difficult to cut crop, resulting in less sickle knock. Sickle Over-stroke Hold Down Clips The hold down clips require no adjustment, but if bent, can easily be straightened with a hammer. The sickle hold downs don’t need regular adjustment, which saves the operator time.
FEATURES AND BENEFITS DHW DRAPER HEADER DRAPER CONVEYOR Draper Belts The draper belts are made of heavy duty polyester with a nylon ply for extra durability. The belt has been improved with heavier nylon reinforcement, giving the belt more rigidity and less stress concentration. The belts are 41 in (1041 mm) wide, with fiberglass rod reinforced cross slats. The heavy duty belt with reinforced cross slats provides a longer lasting draper belt for less maintenance costs.
FEATURES AND BENEFITS DHW DRAPER HEADER Draper Belt Tension Adjustment The draper belts are tightened using a ratchet style tension adjustment. The draper belt tension is maintained by rotating the top of the ratchet gear toward the outside of the header to tighten the belts. The ratchets can be easily released for belt storage. Proper draper belt tension results in longer belt life and lower repair costs.
FEATURES AND BENEFITS DHW DRAPER HEADER HEADER FRAME End Panel Shield The sickle drive on the left end panel is shielded, to help reduce the incidence of crop hair-pinning, and crop stripping. End Shield Crop Dividers The crop dividers divide the crop on each end of the header to reduce the possibility of stripping. Also, the guard position is centered between the end panels, which also helps reduce crop stripping.
FEATURES AND BENEFITS DHW DRAPER HEADER Header Walkway A walkway with a non-slip surface is designed into the header. The walkway can be accessed from the tractor’s left side platform. The walkway with handles on the cab gives the operator a non-slip platform to clean the cab windows. Header Walkway Hydraulic Guard Angle The hydraulic guard angle adjustment is standard on the SP115B and SP185B. It is available as an optional kit on the SP85B.
FEATURES AND BENEFITS DHW DRAPER HEADER HYDRAULICS Reel Drive The reel speed is infinitely adjustable from the tractor seat from 0 to 63 rpm. It is beneficial to adjust the reel speed depending on crop, field conditions, and ground speed. Reel Drive Reel Lift The reel height is adjusted hydraulically with the reel lift cylinders. The reel lift is controlled by the top button on the cab travel control lever. The operator can adjust the reel height on the go to best match changing crop conditions.
FEATURES AND BENEFITS DHW DRAPER HEADER OPTIONAL KITS (FIELD INSTALLED) Choice of Reel Challenger offers both the Hart Carter and the Universal UII pickup reels. Each reel has it’s own benefits, so the customer can choose the reel best suited to the conditions. Hart-Carter (HCC) Series II Pickup Reel The Hart Carter reel features a smooth crop flow of material into the header.
FEATURES AND BENEFITS DHW DRAPER HEADER Universal Pickup Reel (UII) The Universal reel is designed to separate, hold, and continuously deliver crop onto the drapers in a smooth, even flow. The UII reel is robustly built, for extra long life. The reel is equipped with plastic polytine fingers, which are more durable than steel tines, for reduced maintenance. UII Reel The UII reel has five bats. The reel tine sweep shows the “flip over” action of the reel tines after it has released the crop.
FEATURES AND BENEFITS DHW DRAPER HEADER Fixed Gauge Wheels The 16 x 6.50-8 gauge wheels are used to keep the header cutting parallel to the ground, and to keep the header from digging in on uneven ground. The gauge wheels can be set in one of 32 height settings. The gauge wheels allow the header to cut lower to the ground than with the optional skid shoes. Wholegoods Kit – BK61058 Fixed Gauge Wheels Estimated Installation Time – 1.0 Hr.
FEATURES AND BENEFITS DHW DRAPER HEADER Plastic Wear Plate on Cutterbar The plastic wear plate is used to reduce wear on the underside of the cutterbar when cutting low to the ground. When cutting crops low to the ground, the ideal combination is the plastic wear plate and gauge wheels. Do not use the plastic wear plates with skid shoes. Wholegoods Kit – 18’ - BK61123 22’ – BK61124 25’ – BK61125 30’ – BK61126 Wear Plate Estimated Installation Time – 3.0 Hr.
SPECIFICATIONS SP85B WINDROWER MODEL .....................................................................SP85B Self-Propelled Windrower Tractor DIMENSIONS AND WEIGHTS Length Overall with Header in (mm)................................................................... 257.5 (6540) Wheelbase in (mm) ........................................................................................ 140.0 (3556) Height Top of Cab in (mm) ...................................................................................
SPECIFICATIONS SP85B WINDROWER GROUND DRIVE SYSTEM Final Drive Type ....................................................................................... Double Reduction Planetary Tandem Pump .........................................................................Sauer-Danfoss, Series M44 Motors ..................................................... Sauer-Danfoss, Series M44 Fixed Displacement Speed (Approximate) mph (km/h) .............................................................
SPECIFICATIONS SP85B WINDROWER ACCESSORIES Lighting Work Lamps.....................................................................7 rectangular halogen lamps and 1 rectangular enhanced halogen lamp Marking and turn signals ...................4 rectangular amber lamps, 2 rectangular red lamps, and 2 round amber lamps Rear View Mirrors..................................................Right-hand side, left-hand side, and in cab Controls .........................................................................
SPECIFICATIONS SP115B WINDROWER MODEL ............................................................................... SP115B Self Propelled Windrower DIMENSIONS AND WEIGHTS Length Overall with Auger Header in (mm) ........................................................ 257.5 (6540) With Draper Header in (mm) ...................................................... 280.3 (7120) Wheelbase in (mm) ...........................................................................................
SPECIFICATIONS SP115B WINDROWER ELECTRICAL SYSTEM System Voltage ....................................................................................................................12 Ground .......................................................................................................................Negative Batteries Quantity..............................................................................................................................2 Capacity, Each.................................
SPECIFICATIONS SP115B WINDROWER AIR CONDITIONING System size BTU/hr......................................................................................................22,000 Refrigerant .............................................................................................................. HFC 134a Capacity lb (kg) ......................................................................................................... 4.0 (1.8) Compressor ............................................................
SPECIFICATIONS SP185B WINDROWER MODEL ...................................................................SP185B Self-Propelled Windrower Tractor DIMENSIONS AND WEIGHTS Length Overall with Header in (mm)................................................................... 255.9 (6500) Wheelbase in (mm) ........................................................................................ 140.0 (3556) Height Top of Cab in (mm) ...................................................................................
SPECIFICATIONS SP185B WINDROWER ELECTRICAL SYSTEM System Voltage ....................................................................................................................12 Ground .......................................................................................................................Negative Batteries Quantity..............................................................................................................................2 Capacity, Each.................................
SPECIFICATIONS SP185B WINDROWER AIR CONDITIONING System Size BTU/hr .....................................................................................................22,000 Refrigerant .............................................................................................................. HFC 134a Capacity lb (kg) ......................................................................................................... 4.0 (1.8) Compressor ............................................................
SPECIFICATIONS AHB AUGER HEADER MODEL ....................................................................................................... AHB Auger Header DIMENSIONS AND WEIGHTS 14 FT Header Width of Cut in (mm) ......................................................................................... 168 (4276) Width (Overall) in (mm) .................................................................................. 188.4 (4786) Weight (Less Forming Shields) lb (kg) .....................................
SPECIFICATIONS AHB AUGER HEADER AUGERS Type .................................................................................................. Dual, Opposed Rotation Diameter Upper Auger in (mm)............................................................................................... 9 (229) Lower Auger in (mm)............................................................................................... 9 (229) Speed Upper Auger rpm .....................................................................
SPECIFICATIONS DHW DRAPER HEADER MODEL .....................................................DHW Center Delivery And Shiftable Draper Header DIMENSIONS AND WEIGHTS Overall Width Center Delivery and Double Swath Model 22 ft (6.7 m) in (m) ......................................................................................... 278 (7.06) 25 ft (7.6 m) in (m) ......................................................................................... 314 (7.98) 30 ft (9.1 m) in (m) ...............................
SPECIFICATIONS DHW DRAPER HEADER HEADER Drive - Draper and Reel ............................................................................................Hydraulic Guard Angle (4 Cylinder Tractors, Adjustable) ...........................................................9° to 19° Guard Angle (6 Cylinder Tractors, Adjustable) ...........................................................4° to 18° Flotation .................................................................................................
SPECIFICATIONS DKHB DISC HEADER MODEL ....................................................................................................... DKHB Disc Header DIMENSIONS AND WEIGHTS 12’ Header Width (Overall) in (mm) ..................................................................................... 150 (3810) Weight (With Forming Shields) lb (kg)............................................................. 3490 (1583) 15’ 3” Header Width (Overall) in (mm) .................................................
SPECIFICATIONS DKHB DISC HEADER HAY CONDITIONER Type .................................................................................... Engaging Rollers, Steel on Steel Length in (mm) ...................................................................................................... 110 (2794) Diameter in (mm).................................................................................................... 7.75 (197) Speed (maximum) 12’ Header rpm .....................................................
COMPETITIVE COMPARISONS SP85B WINDROWER POWER UNITS ENGINE Make Displacement Cu. In. Aspiration Horsepower Rated rpm Cooling System U.S. Qt. Aspirated Air Pre-Cleaner Air Intake Screen Cleaner Number of Batteries Alternator Rating Amps Fuel-Tank Capacity U.S. gal. HYDRAULIC SYSTEM Header Drive System gpm Drive System Relief Pressure psi Reservoir Capacity U.S. gal.
COMPETITIVE COMPARISONS SP85B WINDROWER POWER UNITS CAB Steering Wheel Tilt Positions Steering Column Tilt Positions Instructional Seat Header Lift Control Header Tilt from Cab Header Drive Control Instrumentation Engine/Transmission Protection Ground Speed Indicator Windshield Wiper Number of Cab Mirrors Tinted Glass ft² CHALLENGER® SP85B NH HW300 CASE IH WDX901 MACDON 9250 9 5 Yes Electro-hyd Optional Electric Analog Light/Buzzer Yes Optional 3 73 Infinite 7 Optional Electro-hyd Standard Electric Ele
COMPETITIVE COMPARISONS SP115B WINDROWER POWER UNITS ENGINE Make Displacement Cu. In. Aspiration Horsepower Rated rpm Cooling System U.S. Qt Aspirated Air Pre-Cleaner Air Intake Screen Cleaner Number of Batteries Alternator Rating Amps Fuel-Tank Capacity U.S. Gal. HYDRAULIC SYSTEM Header Drive System gpm Drive System Relief Pressure psi Reservoir Capacity U.S. Gal.
COMPETITIVE COMPARISONS SP115B WINDROWER POWER UNITS CAB Steering Wheel Tilt Positions Steering Column Tilt Positions Instructional Seat Header Lift Control Header Tilt from Cab Header Drive Control Speed Range Control Instrumentation Engine/Transmission Protection Ground Speed Indicator Windshield Wiper Number of Cab Mirrors Heater Tinted Glass ft² CHALLENGER® SP115B JOHN DEERE 4890 MACDON 9352I 9 5 Yes Electric Standard Electric Electric Electronic Light/Buzzer Yes Optional 3 Yes 73 Yes 4 Yes Electri
COMPETITIVE COMPARISONS SP115B WINDROWER POWER UNITS ENGINE Make Displacement Cu. In. Aspiration Horsepower Rated rpm Cooling System U.S. Qt Aspirated Air Pre-Cleaner Air Intake Screen Cleaner Number of Batteries Alternator Rating Amps Fuel-Tank Capacity U.S. Gal. HYDRAULIC SYSTEM Header Drive System gpm Drive System Relief Pressure psi Reservoir Capacity U.S. Gal.
COMPETITIVE COMPARISONS SP115B WINDROWER POWER UNITS CAB Steering Wheel Tilt Positions Steering Column Tilt Positions Instructional Seat Header Lift Control Header Tilt from Cab Header Drive Control Speed Range Control Instrumentation Engine/Transmission Protection Ground Speed Indicator Windshield Wiper Number of Cab Mirrors Heater Tinted Glass ft² CHALLENGER® SP115B 9 5 Yes Electric Standard Electric Electric Electronic Light/Buzzer Yes Optional 3 Yes 73 NH HW320 NH HW305S NH HW325 CASE IH WDX1101 CASE
COMPETITIVE COMPARISONS SP185B WINDROWER POWER UNITS ENGINE Make Displacement (Cu. In.) Aspiration Horsepower Rated Speed (rpm) Cooling System (U.S. Qt.) Aspirated Air Pre-Cleaner Air Intake Screen Cleaner Number of Batteries Alternator Rating (Amps) Fuel-Tank Capacity (Gal.) HYDRAULIC SYSTEM Drive System Relief Pressure Reservoir Capacity (Gal.
COMPETITIVE COMPARISONS SP185B WINDROWER POWER UNITS (CONTD.
COMPETITIVE COMPARISONS AHB AUGER HEADER AUGER HEADERS Sizes Available (Ft) Lift Range (In) Header Drive # Belts in Drive System Flotation On the Go Flotation Adjustment CUTTERBARS Number of Sickles Sickle Drive Sickle Stroke (In) Sickle Speed (SPM) Type of Sickles Guard Angle Range (Degree) Number of Skid Shoes Skid Shoe Positions Gauge Wheels REELS Number of Bats Type of Drive Drive Protection Diameter Speed Range (rpm) AUGERS Number of Augers Diameter (In) Flighting Depth (In) Speed rpm Type of Drive Dr
COMPETITIVE COMPARISONS DHW DRAPER HEADER SHIFTABLE DRAPER HEADERS Sizes Available Lift Range Header Drive Flotation On the Go Flotation Adjustment CUTTERBARS Number of Sickles Sickle Drive Sickle Stroke Sickle Speed (SPM) Type of Sickles Guard Angle Range (Degree) Number of Skid Shoes Gauge Wheels REELS Number of Bats Type of Drive Diameter Speed Range (rpm) DRAPER Delivery Opening Width WEIGHTS 21’ Header & PU Reel (Lb) 25’ Header & PU Reel (Lb) 30’ Header & PU Reel (Lb) CHALLENGER® DHW 22’, 25’, 30’ Hyd
COMPETITIVE COMPARISONS DKHB DISC HEADER DISC HEADER Cutting Width Lift Range In Header Drive Flotation On the Go Flotation Adjustment CUTTERBED Number of Discs Oil Reservoir Capacity Header Tilt Angle (Degrees) Gauge Wheels CONDITIONERS Type Material Pressure System Length (In) Roll Speed (rpm) Roll Diameter (upper) In Roll Diameter (lower) In Roll separation Type of Drive Discharge Range In DIMENSIONS Overall Width (In) Weight (Lb) CHALLENGER® DKHB 12’ and 15’ 3” -3 to 25 Hydraulic Motor Hydraulic Standa
COMPETITIVE COMPARISONS SP85B-SP115B WINDROWERS Challenger® features to sell compared to the New Holland HW300 and HW320 or Case IH WDX901 and WDX1101 Tractor ♦ Hydraulic header flotation, for longer header life and ease of operator adjustment, as compared to spring flotation. ♦ Caterpillar engine, noted for economy, reliability, long life and excellent service network. ♦ Easy serviceability of tractor, evidenced by tilting engine cover, as compared to only flip up side shields.
COMPETITIVE COMPARISONS SP85B-SP115B WINDROWERS Challenger® features to sell compared to the John Deere 4895 Tractor ♦ Caterpillar engine noted for economy, reliability, long life, and excellent service network. ♦ Easy serviceability of tractor, evidenced by tilting engine cover, as compared to only flip up side shields. ♦ Natural front to rear engine airflow, for more efficient engine cooling. ♦ Engine air intake sits up forward and high, away from most chaff.
COMPETITIVE COMPARISONS SP85B-SP115B WINDROWERS Challenger® features to sell compared to the MacDon 9250, 9350, and 9352i Tractor ♦ Hydraulic header flotation, for longer header life and ease of operator adjustment, as compared to spring flotation. ♦ Hydraulic header drive, for easier header installation and smoother header operation, as compared to shaft drive. ♦ Large drive tires, for superior ride at all field speeds. ♦ Natural front to rear engine airflow, for more efficient engine cooling.
COMPETITIVE COMPARISONS AHB AUGER HEADER Challenger® features to sell compared to the New Holland HS Auger Header (Case IH HDX) Cutterbar ♦ Cutterbar maintenance is significantly reduced by the use of full width sickle hold down. ♦ Half swaybar sickle drive is simple and built for long life. Reel ♦ All reel tine tubes pivot on sealed ball bearings for longer life. Augers • Dual augers deliver crop to conditioner rolls smoother and with less abrasion than single floating auger, for higher quality windrows.
COMPETITIVE COMPARISONS AHB AUGER HEADER Challenger® features to sell compared to the John Deere 895 Auger Header Cutterbar ♦ Cutterbar maintenance is significantly reduced by the use of full width sickle hold down. ♦ Half swaybar sickle drive is simple and built for long life. Reel ♦ Reel tine tubes pivot on sealed ball bearings for longer life. ♦ Reel tine tubes are segmented to make replacing reel tines easier. Augers ♦ Dual augers are each protected with a slip clutch.
COMPETITIVE COMPARISONS AHB AUGER HEADER Challenger® features to sell compared to the MacDon 922 Auger Header Cutterbar ♦ Cutterbar maintenance is significantly reduced by the use of full width sickle hold down. ♦ Half swaybar sickle drive is simple and built for long life. Augers • Dual augers deliver crop to conditioner rolls smoother and with less abrasion than a single auger, for higher quality windrows. Hay Conditioner ♦ Wide 110” conditioner rolls for improved crop conditioning.
COMPETITIVE COMPARISONS SP185B WINDROWER / DKHB HEADER Challenger® features to sell compared to the New Holland HW340 and 2355 Disc Header (or Case IH WDX1701 and RDX161 Disc Header) Header ♦ Gear-to-gear cutterbed, as compared to modular cutterbed. Less maintenance. One fill and one drain plug instead of 12 drain plugs and 12 fill plugs. ♦ All gears are shaved, and bearings are sealed, for less contamination and longer life. ♦ Low profile cutterbed cuts lower with less crop scalloping.
COMPETITIVE COMPARISONS SP185B WINDROWER / DKHB HEADER Challenger® features to sell compared to the John Deere 4995 and 994 and 995 Disc Header Header ♦ All gears accessible from the top of the cutterbed. Maintenance is easier, all gears are shaved, and bearings are sealed. ♦ Cage conveyors and turbulence reduction roll. Higher productivity and smoother windrows in both tall and short crops. ♦ Cutterbed efficiency. Lower horsepower requirement to achieve best productivity.
