User guide MAC 201 REF.
Contents 4 General safety instructions 4 Types of notices 5 Basic safety instructions 6 Introduction 6 General description 6 Main features 7 General use of the unit 9 Unit installation and configuration 9 Installation 9 Power connection 10 Fast menu guide 11 Main menu 18 Advanced configuration of the unit 18 User interface via web browser 20 Maintenance 20 Unit care 20 Troubleshooting 21 Technical specifications 21 MAC 201 model 22 Warranty 22 Unit recycling 23 CE
General safety instructions/Types of notices General safety instructions JJ Read all of this user manual carefully before plugging in the unit. JJ Always have these instructions to hand during installation. JJ Follow all of the instructions and safety notices regarding unit handling. Types of notices The meaning of the safety notices used in this manual are described below. DANGER of DEATH OR INJURY DANGER This safety notice indicates a possible danger for the life and health of people.
General safety instructions/Basic safety instructions Basic safety instructions EN DANGER of DEATH OR INJURY JJ Do not install the unit during an electrical storm. This could lead to electrostatic discharge from lightning. JJ Do not open the unit. There is a risk of electrostatic discharge. DANGER RISK OF damage to the unit JJ The unit must be appropriately ventilated. Install the unit in a dust-free location. Do not place the unit in a location where the ventilation slots are covered or blocked.
Introduction/General description Introduction General description KEY 1 Mains connector 2 Front panel with cluster map 3 Display (LCD) 4 Control button 5 Video input 1 6 Audio input L 1 7 Audio input R 1 8 Video input 2 9 Audio input L 2 10 Audio input R 2 11 Ethernet connector 12 TV Loopthrough input 13 TV COFDM output Main features The MAC 201 model is an AV analogue TV signal to COFDM digital TV signal standalone modulator unit.
Introduction/General use of the unit JJ FF Reprogrammable as many times as required. FF Firmware updated via Ethernet connection with web browser. EN Signal processing: FF Double CVBS stereo video-audio input. FF Supported video standards: PAL/SECAM/NTSC. FF MPEG2 coding. FF RF DVB-T output, compatible with TDT. FF RF output, adjustable in VHF and UHF bands. FF Loopthrough for combination of additional RF TV signals. JJ Dimensions: 302 mm x 251 mm x 44 mm JJ Weight: 1.
Introduction/General use of the unit Visual indications on the LCD display This symbol visually indicates the possibility of moving vertically. Vertical button movement In the menus and submenus, move the button up or down to browse upwards and downwards position by position. In the settings, move the button up or down to modify values position by position. NOTE Keep the button pressed up or down to browse or to modify values more quickly.
Unit installation and configuration/Installation Unit installation and configuration EN The LCD display and the control button are sufficient for the basic settings of the unit. Follow the steps indicated below to install the unit and configure the various parameters accessible from the user interface on the LCD display. Installation RISK OF damage to the unit ATTENTION Mechanical handling of the unit while it is switched on may lead to it being damaged.
Unit installation and configuration/Fast menu guide Fast menu guide 10
Unit installation and configuration/Main menu Main menu EN Note Over the following pages, the field locating and selection method is primarily indicated by the “vertical button movement” and “press button” icons. However, horizontal button movement can be used to locate and select fields, as indicated in the General use of the unit.
Unit installation and configuration/Main menu b) Locate and select the option IP address. Enter the 12-digit sequence corresponding to the static IP address of the unit. c) Locate and select the option IP mask. Enter the 12-digit sequence corresponding to the IP mask of the unit. d) Locate and select the option Default Gateway. Enter the 12-digit sequence corresponding to the IP direction of the LAN gateway. Setting the time 2) Locate and select the option time-Date.
Unit installation and configuration/Main menu Blocking the LCD and joystick 6) EN Locate and select the option lock LCD to block access to the configuration from the LCD display and using the control button. a) Activate (ON) or deactivate (OFF) the blocking option. b) Establish a code to unlock the unit if this option has been activated. Setting the signals note The unit can switch the input signals; alter their brightness, contrast and saturation conditions; and adjust the output carrier in RF.
Unit installation and configuration/Main menu f) Locate and select the option Aspect ratio 1. The possible aspect ratio values are 1:1, 4:3 and 16:9. note If you keep pressing the control button down you will access the information and configuration of the second input signal. Configuration of the carrier services 2) Locate and select the option Services. a) Locate and select the option CH1 video audio. Activate (ON) or deactivate (OFF) the video and audio signals of the first input.
Unit installation and configuration/Main menu a) Locate and select the option Frequency. Configure the output frequency value between 45 MHz and 865 MHz. b) Locate and select the option Attenuation. Select the output attenuation between 0 and 47 dB. c) Locate and select the option OFDM mode. Select the OFDM mode between 2k and 8k subcarriers. d) Locate and select the option Bandwidth. Select the bandwidth between 6, 7 and 8 Mhz. e) Locate and select the option Guard interval.
Unit installation and configuration/Main menu b) Locate and indicate output bitrate. The unit displays the output data speed in mbits/s. c) Locate and indicate null min act max. The unit displays the volume of null data packets in the output (minimum, actual and maximum) as a percentage of the total. d) Locate and indicate Temperature. The unit displays its temperature. Unit information 1) Locate and indicate the option Module info. a) Locate and indicate the option Model.
Unit installation and configuration/Main menu 2) Enter the unblocking code assigned by the unit operator through the web interface. 3) The unit displays the validity of the code. EN note The unit will remain unblocked until it is restarted or the operator deactivates the block from the web interface. To unblock the unit without the blocking code: 1) Locate and select Information. 2) Contact the supplier of the unit and provide the serial number.
Advanced configuration of the unit/User interface via web browser Advanced configuration of the unit User interface via web browser The web interface allows you to fully configure the MAC 201 unit through an Ethernet connection and a web browser. NOTE To display the graphics provided in the unit configuration program correctly, we recommend installing the web browser Mozilla Firefox 1.5 or higher (www.mozilla. com) in the control PC. NOTe Cookies and Javascript must be enabled.
Advanced configuration of the unit/User interface via web browser NOTE EN The unit also has the IP address 10.254.254.254 assigned by default. This IP address may not be modified by the user. 4) Press INTRO to access to the welcome screen. 5) Enter the user name “Admin” and the password “admin”. NOTE The process of configuration and setting via Ethernet connection is explained in the “Web interface user manual” available at http://www.ikusi.com.
Maintenance/Unit care Maintenance Unit care HANDLING THE INSIDE OF THE UNIT IS FORBIDDEN Do not dismantle or try to repair the unit, its accessories or its components. This will render the warranty null and void. JJ Do not use the power cable if it is damaged. JJ To disconnect the power cable, pull carefully on the plug and not the cable. JJ To clean the panel and unit connections: FF Unplug the unit. FF Clean with a slightly damp, soft cloth. FF Allow to dry completely before use.
Technical specifications/MAC 201 model Technical specifications EN MAC 201 model Inputs AV1 / AV2 Format CVBS Input level (video) Vpp Input impedance Ω Video standards Yes / No Vpp Output 0.5 - 4.0 COFDM digital TV COFDM standard Bandwidths 75 PAL/SECAM/NTSC Analogue / digital audio Input level (audio) 0.7 - 1.
Warranty/MAC 201 model Warranty Notwithstanding any complaints made to the direct vendor of the product, IKUSI offers unit users a two-year warranty as of the invoice date, which shall become valid on presenting the receipt of purchase. During the warranty period, IKUSI is responsible for any faults arising due to material or manufacturing defects and shall repair the receiver or replace it for another corresponding to the state of technology at that time.
CE Certificate/MAC 201 model CE Certificate EN By reproducing the CE marking, IKUSI guarantees unit compliance with the corresponding harmonised standards. EC-Declaration of Conformity marking We, Manufacturer IKUSI, Angel Iglesias, S.A.
Ángel Iglesias, S.A. Paseo Miramón, 170 20009 San Sebastián, Spain Tel. +34 943 44 88 00 Fax +34 943 44 88 20 ikusi@ikusi.com www.ikusi.
