Owner`s manual

38
against staining and scaling. Once the spa is lled, add the
prescribed dose of Water Clarier. This will clear the water of
any micro-particulates that may be in the new water.
Step 2: If possible, have your authorized Bullfrog Spa dealer
test the calcium hardness (CH) of your spa water. Adjust the
CH to 150-200 parts per million (PPM).
Step 3: Test and adjust the Total Alkalinity (TA). TA should
measure 125 to 150 PPM.
Step 4: Test and adjust the pH. Water pH should measure 7.4
to 7.6.
Step 5: After the spa water has circulated for 1 hour, Super
Sanitize the water by adding 2 teaspoons (10cc) of Granular
Chlorine (Dichlor-type only) or 4 teaspoons (20cc) of Granular
Bromine per 200 gallons (909.2l) of spa water. (For complete
details, refer to the Super Sanitation section.) After several
hours, check sanitizer level and adjust, if necessary, to the
following:
Without Ozone With Ozone
Chlorine Level 3.0-5.0 PPM* 2.0-4.0 PPM
Bromine Level 6.7-11.0 PPM 5.7-10.0 PPM
*PPM=Parts per million
IMPORTANT: Do not enter the spa water until the sanitizer
range is within the above stated boundaries. NOTE: If the
sanitizer level is too high, simply wait as the sanitizer level will
naturally drop over time.
Step 6: Startup water chemistry is now complete. However, it
may take several days for the lter to completely clear the
water.
Maintaining Spa Water
Sanitizer and pH Levels
It is important to test and adjust the sanitizer and pH levels of
your spa on a frequent basis. These tests should be performed
prior to each use of the spa. At a minimum, it is
recommended that you test the spa water 2-3 times a week,
regardless of use.
Always test the pH level before you test the sanitizer level. If
the pH level is not within the correct range (7.4-7.6), make the
necessary adjustments.
With each sanitizer test, use either granular Chlorine
(Dichlor-type only) or granular Bromine to maintain the
following levels:
Without Ozone With Ozone
Chlorine Level 3.0-5.0 PPM 2.0-4.0 PPM
Bromine Level 6.7-11.0 PPM 5.7-10.0 PPM
IMPORTANT: To maintain the level of sanitizer with Bromine or
Chlorine (Dichlor-type only) tablets, contact your authorized
Bullfrog Spa dealer for assistance.
Super Sanitation
Super Sanitize the water once a week by adding one of the
following:
2 teaspoons (10cc) of granular Chlorine per 200 gallons
(909.2l) of water
4 teaspoons (20cc) of granular Bromine per 200 gallons
(909.2l) of water
NOTE: To Super Sanitize your spa water using a non-chlorine
shock (Potassium Peroxymonosulfate or equivalent) refer to
the chemical manufacturer’s instructions or see your
authorized Bullfrog Spa dealer for assistance.
NOTE: Super sanitation may be required more than once per
week for heavy usage.
Stain and Scale Control
Use a Stain and Scale Inhibitor per the manufacturer’s
instructions. Add the chemical 3-4 days after Super
Sanitation.
Foam Control
Use a Foam Remover per the manufacturer’s instructions as
needed.
Cloudy Water Prevention and Control
Use a Water Clarier per the manufacturer’s instructions. Add
the chemical 3-4 days after Super Sanitation.
Water Chemistry Troubleshooting
Prior to each spa use, check the water. If the water appears
cloudy or off-color, has signicant surface foam, or excessively
smells of chlorine or bromine, than water needs to be treated
or drained. Using the spa in these conditions could result in a
skin rash or irritation or possibly an infection or other serious
health risk. For assistance in handling spa water chemistry,
contact your authorized Bullfrog Spa dealer or another
service center capable of performing a computerized water
analysis.
•
•
Maintenance