Owner`s manual
24
spa will have steady, every day use, because this mode
maintains the spa water at the set temperature and is
always ready for use. The drawback of Standard Mode is the
pumps and heater do cycle on every thirty minutes
throughout the day, and therefore this mode uses more
electricity than other modes. “Standard” will appear in the
display when in Standard Mode.
Economy Mode (Ecn): only heats the water during lter
cycles—usually twice a day. Economy Mode is named such
because it uses less electricity than Standard Mode.
However, since Economy Mode only maintains and heats
water temperature during ltration cycles, the spa water
temperature may drop a few degrees between the lter
cycles depending on outside temperatures. For this reason,
most spa owners using Economy Mode set their lter cycle
times to correspond with the times of day when they are
most likely to use their spa so the spa water is up to
temperature and ready for use. Economy Mode is preferable
for those who use their spa intermittently (2-3 times per
week). When in Economy Mode, “Economy” will appear in
the display. When jets 1 is pressed in Economy Mode, the
spa goes into “Standard-In-Economy” mode (SE). The
benet of the SE feature is the spa water will heat between
ltration cycles (assuming jets 1 is pressed) allowing
someone to use the spa. The spa reverts back to Economy
mode automatically after 1 hour.
Sleep Mode (SLP): heats the spa during lter cycles to about
20°F (11°C) lower than the set temperature. The Sleep Mode
uses the least electricity of any of the modes, but since it
takes several hours to bring the spa water back up to set
temperature, Sleep Mode is only recommended if the spa
will not be used for 2-3 weeks or more. In Sleep Mode, “Sleep”
will appear on the display.
Standby Mode (Sby)
Standby Mode idles all of the spa’s functions and should be
used when changing a lter or a JetPak, otherwise the pumps
can automatically turn on at the start of a ltration cycle.
Press temp then jets 2 (or aux) to enter Standby mode. Press
any button to exit.
Filter Cycles
Filter cycles are preset at the factory to run twice per 24 hour
period—one starting at 8:00 a.m. and one starting at 8:00 p.m.
The ltration pump (either pump 1 or optional circ pump) and
the ozone purier* run during ltration cycles. In addition, all jet
pumps will run for the rst 10 minutes of each lter cycle to purge
the JetPaks
™
and JetPods
™
. The factory setting lter cycle duration
is set for 2 hours each cycle (4 hours per day) for non-circ models,
•
•
(to increase hour) or cooler (to decrease hour). Each press
changes the time by 1 hour. Once the hour is correct, press
mode/prog to enter the correct hour and switch to minutes.
Select minutes by pressing warmer (for up) or cooler (for
down). Each press changes the time by 1 minute. Either press
time to save current time and exit, or if desired, press mode/
prog to enter the optional lter cycle programming (see
Custom Filter Cycles section below).
NOTE: In the event of power loss to the spa, the time setting is
saved for up to 72 hours.
Icon Legend
Heat Icon - Indicates different stages of
heating.
Jets Icon - Spins fast on high speed/spins
slow on low speed
Light Icon
Setting the Temperature: 80°F-104°F (26°C-40°C)
Once the lter pump has been running for at least 2 minutes,
the actual water temperature will be displayed on the Liquid
Crystal Display (LCD) on the control pad.
Note: Any time the spa lter pump has not been running for a
period of time, the LCD display will usually read “----“, which
means the temperature is unknown as the temperature sensors
in the heating unit require the water to be circulating past
them for a couple minutes before calculating a true water
temperature reading.
Unless changed by the user, the default temperature is
factory set to 100°F (38°C). To change the spa water
temperature, press warmer or cooler once to display the
current set temperature, then within 2 seconds press warmer
to raise set temperature or cooler to lower set temperature.
Pressing warmer or cooler multiple times raises or lowers set
temperature one degree each time the button is pressed.
After 3 seconds without pressing warmer or cooler, the LCD
will again display the current spa water temperature.
Spa Operating Modes
Press mode/prog to enter mode programming, then press
cooler to cycle through the operating modes (Standard,
Economy and Sleep). Select the desired mode by pressing
mode/prog.
Standard Mode (Std): which is the factory default setting,
checks and maintains the set temperature of the spa water
every 30 minutes. Standard Mode is preferable when your
•
Operation