Owner`s manual
22
temperature, press temp once to display the current set
temperature, then press temp additional times to increase (or
decrease) the set temperature. To change the temperature
adjustment direction (i.e.: from increase to decrease), pause
3-5 seconds between pressing temp, then push temp multiple
times to desired temperature. After 3 seconds without pressing
temp, the LCD will again display the current spa water
temperature.
Spa Operating Modes
A multi-button sequence is used to switch between Standard,
Economy, and Sleep modes. Press temp + light to enter mode
programming. Press temp to cycle through to desired mode,
then press light to conrm selection.
Standard Mode (Std): which is the factory default setting,
checks and maintains the set temperature of the spa water
every 30 minutes. Standard Mode is preferable when your
spa will have steady, every day use, because this mode
maintains the spa water at the set temperature and is
always ready for use. The drawback of Standard Mode is the
pumps and heater cycle on every thirty minutes throughout
the day, and therefore this mode uses more electricity than
other modes. “Std” will appear in the display momentarily
when you switch into Standard Mode.
Economy Mode (Ecn): only heats the water during lter
cycles—usually twice a day. Economy Mode is named such
because it uses less electricity than Standard Mode.
However, since Economy Mode only checks and maintains
temperature during ltration cycles, the spa water
temperature may drop a few degrees between the lter
(heating) cycles depending on outside temperatures. For
this reason, most spa owners using Economy Mode set their
lter cycle times to correspond with the times of day when
they are most likely to use their spa so the spa water is up to
temperature and ready for use. Economy Mode is preferable
for those who use their spa intermittently (2-3 times per week).
When in Economy Mode, “Ecn” will appear solid in the
display when the spa is heating and will ash intermittently
when the spa is not heating.
When jets 1 is pressed in Economy Mode, the spa goes into
“Standard-In-Economy” mode (SE). The benet of the SE
feature is the spa will heat (as jets 1 is pressed) for one hour,
which allows the spa water to heat if someone is using the
spa between ltration cycles. The spa reverts back to
Economy Mode automatically after 1 hour.
Sleep Mode (SLP): heats the spa during lter cycles to about
20°F (11°C) lower than the set temperature. The Sleep Mode
uses the least electricity of any of the modes, but since it
•
•
•
takes several hours to bring the spa water back up to set
temperature for comfortable use, Sleep Mode is only
recommended if the spa will not be used for 2-3 weeks or
more. In Sleep Mode, “SLP” will appear on the display.
Standby Mode (Sby)
Standby Mode idles all of the spa’s functions and should be
used when changing lters or JetPaks, otherwise the pumps
can automatically turn on at the start of a ltration cycle.
Press temp then jets 2 or aux to enter Standby mode. Press
any button to exit this mode.
Jets 1
Press jets 1 to turn pump 1 on and off and to shift between
low and high speeds. If left running, the low speed will
automatically turn off after 2 hours and the high speed will
turn off after 30 minutes. In non-circ pump spas, pump 1 turns
on in low speed automatically during lter cycles, and it
cannot be turned off with the control panel jets 1 switch.
NOTE: When in standard mode, the lter pump (either pump
1-low speed or optional circ pump) will activate for at least 2
minutes every 30 minutes to detect the spa temperature and
will heat to set temperature (if needed).
Jets 2 (optional)
If your spa is equipped with a two jet pump system, press jets
2 to turn pump 2 on or off and to shift between low and high
speeds. If left running, the pump will turn off automatically
after 30 minutes.
NOTE: If the spa does not have two pumps, the jets 2 button
will be labeled aux on the control pad.
Auxiliary Jet(s) Control
An optional auxiliary control pad(s) on the side of the spa can
also activate the pump(s).
NOTE: This option is not available on Series II Hot Tub models.
Light
Press light to toggle the light on and off. The light will turn off
automatically after 4 hours.
LED Light (optional)
Press light button to turn the LED light on and off. To toggle
between all the LED color options, press the light button on, then
off, then wait about 1 second and turn on again. A different
color option will appear. The LED light will turn off automatically
after 4 hours.
Preset Filter Cycles
There are two lter cycles per day. The rst lter cycle begins
6 minutes after the spa is powered up. The second lter cycle
Operation