2/5/2015 MSPA FAQ--MSpa Portable Inflatable Bubble Spa
2/5/2015 MSPA FAQ--MSpa Portable Inflatable Bubble Spa | by ORPC--MSpa
http://www.the-mspa.com/care/FAQ.htm 6/10
It’s helpful to put temp barrier mat in between the spa pool and the ground. Similar mat which is made
of foam material or other materials with temp barrier function can also be used.
25. Question:What is needed to prepare a site to set up and use my MSpa tub?
Answer:A flat, smooth and supporting surface with water drainage system is required. Uneven or unsound
surfaces can damage the spa tub and void your warranty. A ground cloth or mat is recommended to
place under the spa pool to prevent scratch or damage of the inflatable spa pool body and heat loss.
Regardless, it's the customer responsibility to make sure the set-up site is properly prepared, whether
on the ground, on a floor, deck, patio or slab. Level the surface before filling spa with water.
26. Question:What is the approximate depth of the water to fill up my spa tub?
Answer:We recommend to fill up your spa about 80% of its maximum water capacity, the depth is about 44-
46cm. (Refer answer to question 10)
27. Question:What is the steepest slope that I am able to set up my spa on?
Answer:For best results the surface should be perfectly level. Pay close attention to the spa’s stability and
levelness in the early stages of filling your spa up with water. If you see about an inch of water is
accumulated, and the water is not spreading out evenly, or the spa appears to be bulging to one side,
stop filling the spa, drain the water, and select a new site. If the spa tub is set up on a slope, the spa
will be lopsided and could collapse.
28. Question:What material is the MSpa inflatable spa tub made of?
Answer:All MSpa hot tubs are made with premium quality and heavy gauge PVC of 0.60mm.
MSpa pool body materials for different models are listed below:
B-091,B-100,B-110,B-112,B-120: Spa pool outside cover is made of Polyester laminated PVC.
B-121,B-130,B-131,B-132,B-140,B-141,B-150,B-151,B-152,J-211,J-213,J-132,J-152: Spa pool body
cover is made of PVC synthetic leather.
B-160,B-170,J-160,J-170: Top part of spa pool liner is made of PVC synthetic leather.
MSpa top lid materials for different models:
B-091,B-100,B-110,B-112,B-120: Polyester and PVC laminated top lid with aluminum foil
B-140,B-121,B-141,B-130,B-131,B-132,B-150,B-151,B-152,B-160,B-170,J-211,J-213,J-132,J-152,J-
160,J-170: PVC synthetic leather with aluminum foil
For all models except MSpa LITE: an inflatable bladder is included in the standard accessories.
29. Question:
What other surfaces can be safely used to set up my spa?
?
Answer:The spa can be set up on pavement that is completely smooth, level and stable. A ground cloth is
recommended. Make sure not to set up your spa tub on sand or muddy ground that is not weight
capable and stable.
30. Question:What should I use to clean my MSpa before storing it for the winter or next season?
Answer:Use mild soap with fresh and clean water. Thoroughly wipe the soap on the inner spa pool and rinse it
with water. Make sure your spa tub is completely dry before storage for next season.
31. Question:Why do I find algae in my spa even when I run my filter pump regularly?
Answer:The pump and filter alone will not prevent algae from growing in the spa water; this can only be done by
maintaining proper chlorine and pH levels at all times. Check your local pool chemical supplies store
for further information.
32. Question:Would excessive spa chemicals affect or cause deterioration to liners?