Operating Instructions Electrically heated connectors series T.-H1, V.-H1 Gas sampling and gas conditioning technology 6-6.
Contents 1 2 3 4 5 6 General information...................................................................................................................... 4 Declaration of conformity ............................................................................................................ 4 Safety instructions ....................................................................................................................... 4 Warranty ...........................................................
Dear customer, we have made up this operating manual in such a way that all necessary information about the product can be found and understood quickly and easily. Should you still have any question, please do not hesitate to contact M&C directly or go through your appointed dealer. Respective contact addresses are to be found in the annexe to this operating manual. Please also contact our homepage www.mc-techgroup.com for further information about our products.
Head Office M&C TechGroup Germany GmbH Rehhecke 79 40885 Ratingen Germany Telephone: 02102 / 935 - 0 Fax: 02102 / 935 - 111 E - mail: info@mc-techgroup.com www.mc-techgroup.com 1 GENERAL INFORMATION The product described in this operating manual has been examined before delivery and left our works in perfect condition related to safety regulations.
Please take care of the following basic safety procedures when mounting, starting up or operating this equipment: Read this operating manual before starting up and use of the equipment. The information and warnings given in this operating manual must be heeded. Any work on electrical equipment is only to be carried out by trained specialists as per the regulations currently in force.
DANGER! This means that death, severe physical injuries and/or important material damages will occur in case the respective safety measures are not fulfilled. WARNING! This means that death, severe physical injuries and/or important material damages may occur in case the respective safety measures are not fulfilled. This means that minor physical injuries may occur in case the respective safety measures are not fulfilled.
6 INTRODUCTION AND APPLICATION In analysis technique, often temperatures must be kept above the sample gas dew point. Therefore, it is absolutely necessary to avoid cold bridges. In order to ensure this, the temperature regulated M&C hose-/tube connectors T..-H1 and V..-H1 are used to connect heated sample lines type 3/4/5-N/M/H with an operating temperature up to 180 °C. 6.1 POWER SUPPLY The electrically heated connectors T.-H1 and V.
7 TECHNICAL DATA Part number Temperaturregler T6-H1 10B1001 (a)** T8-H1 10B1101 (a)** V6-H1 10B1011 (a)** V8-H1 10B1111 (a)** 3x ø 6 mm 3x ø 8 mm 2x ø 6 mm 2x ø 8 mm max. 200 bar max. +180 °C -25 to +60 °C -25 to +80 °C capillary thermostat with high temperature limiter and low temperature alarm 230V 50Hz, 100VA **optionally 115V 60Hz (a) IP 54 EN60529 EN 61010, EN60519-1 350 x 320 x 120 mm (w x h x d) 4,5 kg 8 DESCRIPTION The M&C hose-/tube connectors T.-H1 and V.
9 RECEPTION AND STORAGE Please take the heated connector and possible special accessories carefully out of the packaging material immediately after arrival, and compare the goods with the items listed on the delivery note! Check the goods for any damage caused during delivery and, if necessary, notify your transport insurance company without delay of any damage discovered The heated connector usually is delivered in one packaging unit.
Figure 2 11 Heated connector MOUNTING For mounting the heated connector we recommend the following procedure: Remove the lid of the heated connector by loosening the 4 screws; Remove the thermal conductivity jaws by loosening the 2 screws M4; Remove the upper part of the mounting clamp; Put the heated sample line into the silicone cap and feed the end oft he tube through the hole oft he cap; Remove nut and compression rings of the fitting and put them in right order on the end of the
12 ELECTRICAL CONNECTION WARNING! NOTE! When connecting the equipment, please ensure that the supply voltage is identical with the information provided on the model type plate.
13 STARTING Before using the equipment for the first time, check that the safety measures specific to the installation and process are complied with! For the carried media the corresponding safety regulations and measures have to be considered. WARNING! Before starting up check whether the mains power supply voltage corresponds with the information stated on the nameplate. Beware of touching the filter surface during operation. Serious burns can occur because of high surface temperatures.
14 MAINTENANCE In case of correct use the heated connector works maintenance free. The safety instructions specific to the plant and process are to be consulted prior to any repair work! WARNING! Aggressive condensate is possible.
