GPS&GPRS TRACKING SYSTEM MODULE: GT3000 SERIES User Manual
I. INTRODUCTION GPS GPRS tracking system GT3000 utilize the GPS tracking function and car alarm functions in one unit. You can monitor the vehicle location and control the car alarm remotely. In addition, the unit will send event report if any trigger occurs. It has built-in 8 outputs and 5 inputs to perform essential alarm functions. 1.
device, (1) User detail (Device ID, server IP, and port, SMS number, GPRS APN…) (2) In-built Geo-fence definition (up to 5 circular, 5 rectangular and 20 point Geo-fence shapes can be set in the device) (3) Report setting (Time, Distance, Intelligent mode, Temperature, Low battery, Course change…) (4) ALARM report (to enable or disable the event generated by the inputs, e.g. ignition, DOOR). Those data will have been saved in device’s EEPROM and will not be lost even if the power is failure.
GPS cannot be located when the Immediate Geo-fence function is been executed, GT3000 will use the last known position as the origin of the circular Geo-fence zone to perform the protection. US Patten for immediate Geo-fence function is pending. 1.4 STORE AND FORWARD ABILITY When there is no GPRS service or the server close. The unit will send short message to the server if defined SMS number. All the stored report will be forward to the server when GPRS connection is completed next time. 1.
3. Enable anti-car jacking: (can be performed at any time) If Server sends anti-car jacking command, the system will enter anti-carjacking mode after the unit received the command.
twice. After releasing it, a panic action will be generated. (4) ‘Duty on’ or ‘Duty off’ reports / ‘Status on’ Status off’ reports Press the button (the LED will be temporally stay off) and release it when the LED flashes 3 times. After releasing it, a ‘Duty on’ report will be sent out. To deactivate: Press the button (the LED will be temporally stay off) and release it when the LED flashes 3 times. After releasing it, a ‘Duty off’ report will be sent out.
II. BASIC FUNCTIONS FUNCTIONS GPS GPRS, SMS APPLICATIONS GPS receiver will output a complete position, velocity, and time (PVT) solution in the NMEA Version 3.0 protocol GPRS use standard TCP or UDP communicate protocol. If the GPRS service is failed, the SMS mode will be turned on for emergency use. In-vehicle Door+ 5 input In-vehicle DoorIn-vehicle ignition Temperature sensor port (optional) Valet switch port 1. Parking light (-300mA) 2. Door Lock (-300mA) 3.
Intelligent report (combine time and distance) Keep alive report Temperature report Speeding report Event Report Low battery report Geo-fence trigger report ALARM trigger report, e.g. PANIC mode, ARM, ignition inputs, etc … History data store 3000 report can be saved in unit, and read from server and pc-setup III. STATUS INDICATOR SYSTEM LED: RED: Power indicator. When the unit power on, the led will light all the time.
A. LOGIN DIALOG WINDOW Select the correct COM port number, then “reset” the unit by pressing the reset button, and next click “OK”. Note that: it is necessary to power on and reset the device soon after click the “ok” button. PC setup program will detect the hardware for 60 seconds. If no hardware is detected, it will exit. During the opening up screen shown as below, user can press “Esc” key to terminate the program. B. VERSION NO. CHECKING The below interface will last until correct UNIT Version No.
C. MAIN INTERFACE 1. [USER DETAIL:] If the SIM card is password protected, user can input the “SIM PIN” window to set password of SIM Card. Device ID: Set UNIT ID for the device.
number will display automatically, otherwise it displayed with space. Set Access Point Name (APN), User Name, Password. The maximum length of the APN, User name and Password is 49 characters. TCP/UDP address and Port number of the remote server being set, UNIT will send report to these address. Note that only one TCP or UDP server will be used at the same time. Set the SMS Number of the server. The unit will send reports to the server if GPRS connection is failed.
UNIT can save 3000 reports (3000-1) recently; Click ‘Export’ button can export them with Excel or Text format. Initialize: clear all data in UNIT. Request All: read out the whole existing setting from GT3000. Request: read out the setting in the current page. Apply: transfer the setting to GT3000 in the current pages. Apply All: transfer the whole setting to GT3000. Load: load the saved configuration files. Save: save the current configuration setting to a file.
2. [GEO-FENCE:] Four Circular Geofence and one self-geofence: Circular Geofence must set origin and radius: Origin format :N2446.5321E12120.4231; N2446.5321 is latitude, E12120.4231 is longitude. Radius from 0.1 km to 1000km.
Five rectangular geofence: Set two points position, the point format is N2446.5321E12120.4231; With two points, generate one rectangle. Unit will detect whether in rectangle. When unit enter or leave rectangle, will send one message out. 20 point Geo-fence areas can be set. When UNIT is out of these predefined zones, a report will be generated.
3. [REPORT:] Automatic report can be configured in this section. To activate the function(s), please select “√” in checkbox and fill in data in the textbox.
Parameters: On/Off, Report time when moving, Report time when stop, threshold speed and stop duration. For example: If “√” is selected in the two checkboxes and fill the above data in the textbox, then: The vehicle will send a moving report every 5 minutes when vehicle speed exceed 18km/hr The vehicle will send a stopped report every 1 hours when vehicle speed lower than 18km/hr Even the vehicle speed lower than 18km/hr, and over 5 minutes, unit will send a stop report.
(4) TEMPERATURE REPORT Parameters: On/Off, and min. and max. Temperature. (5) FUEL SENSOR REPORT The fuel sensor is used for calculating current fuel volume, if user selected this item, user can define the value discretionarily. User can set warning fuel level for report. For example, 60 to represent 60% lower level report. (6) COURSE CHANGE REPORT (TO SEND A REPORT WHEN THE COURSE CHANGE IS BIGGER THAN THE VALUE SET HERE) Parameters: On/Off, and course change in degree.
(8) FIXED DISTANCE REPORT Parameters: On/Off, and distance. (Min. distance is 0.1 km, max. distance is 100 km). (9) SPEEDING REPORT: (MIN. SPEED IS 0.1 KM/HR, MAX. SPEED IS 1000 KM/HR). Parameters: on/off, and speed (10) BATTERY REPORT Low battery warning report (to alert user when the internal battery level is low) Parameters: On/Off, and warning battery level for report. For example, 60 to represent 60% lower level report.
(11) KEEP ALIVE PROCEDURE Parameters: On/Off, and interval / retry times. In order to keep connection in GPRS network, the unit can be set to send short keep alive report to the server in order to prevent the disconnection from the mobile service provider. Send reports after a successful keep alive ACK. Parameters: On/Off . If you select this function, all the reports will only be sent out after a successful keep alive ACK. (So if your keep alive time is shorter then select this function will be OK.
(12) GPRS DIAL-UP PROCEDURE 1) GPRS always one-line Parameters: Reconnect interval While using this mode, when the unit can not searched GPRS signal, system will reconnect GPRS interval a preset value. (e.g.: 1minute) 2) Based on report mode Parameters: Max. reconnect times, reconnect interval While using this mode, the unit will connect to the server when there is a report to send. If the first connection is failed, it will retry to connect to the server up to the max. reconnect times.
If the GT3000 is not in the GPRS online status, user can send command &&Y02 or &&Y04 to ask unit to connect to server. This command can be sent from any device via SMS; &&Y02: When received this command, system will actively try to connect to server in next 600 seconds. &&Y04,[connection time],[report interval]: For example: &&Y04, 3600, 60 When received this command, system will connect to server in the next 3600 seconds, and send one report out every 60 seconds.
4. [ALARM REPORT SETUP] Alarm report(s) is also configurable. User can customize the events generated by the in-vehicle input or build in car alarm to be sent to the server. If the item(s) were selected (VALID), the related reports will be sent. Otherwise the report will be ignored even when an event is occurred internally. If input 2 with distance is selected, system will send the distance report every time ignition ON to ignition OFF, for example: %%GT3000, A, 070521024400, N2240.8929E11359.
APPENDIX GT3000 SPECIFICATIONS PHYSICAL PARAMETERS Enclosure dimensions 88(L)*76(W)*25(H) Unit Weight About 100g ELECTRICAL DC Supply voltage 12V OR 24V DC Tolerance voltage 9V Current (GPRS online) 60mA －36V GPRS* Frequency Range (MHz) (Be used in GT3000MT/ GT3000FT/GT3000ST) Frequency Range (MHz) 850/900/1800/1900 900&1800&1900 or 850&1800&1900 GPRS* (Be used in GT3000XT) GPRS connectivity GPRS multi-slot class 10 GPRS mobile station class B (Be used in GT3000MT/ GT3000FT/GT3000XT/GT3000ST
GPS* Channels 20 parallel tracking Frequency L1-1575 MHz Sensitivity Tracking -159 dBm Acquisition (Cold start) -142 dBm Position accuracy (Horizontal) Time to first fix Hot start 1 Warm start 2 Cold 3 ＜2.5m CEP autonomous ＜2.0m CEP SBAX ＜1s ＜32s ＜35s Standard GPS software NMEA message switchable GGA, GSA GSV, VTG, RMC, GLL COMMUNICATION GPRS \SMS\USB ENVIRONMENTAL Operating Temperature -20°C to +55°C Storage Temperature -40°C to +85°C ACCESSORIES 1. 2. 3.
OPTIONAL ACCESSORIES 1. 2. Built in backup battery (optional) Combined Antenna (with GPRS and active GPS) 3. 4. 5. Temperature sensor (optional) PC-setup Cable (optional) Starter kill relay (RL-100) NOTE: Using wrench to tighten the screw cap of GPS and GPRS antenna and lock the screw cap to fix position, for avoid antenna connect abnormality, user can not using hands to tighten the screw cap. VI.
responsible for compliance could void the user’s authority to operate the equipment. 2) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
RELAY TRUNK 12V or 24V OPTIONAL Horn J1 RELAY 12V or 24V Fuse Box FU100 TO VEHICLE 12V or 24V BATTERY TO UNIT OPTIONAL FUEL SENSOR PARKING LIGHT Fuse 5A 1N5401 1N5401 OPTIONAL TEMPERATURE SENSOR LED VALET SWITCH INSTALLATION GUIDE 87 86 85 30 85 30 87 86 BLACK GND PURPLE TRUNK 85 30 87 86 12V or 24V RED BATTERY PC SETUP WHITE/RED ORANGE LAMP GPS ANTENNA GSM ANTENNA OFF ACC ON START OPTIONAL BLUE (-)LOCK OUTPUT -300mA GREEN/BLACK CH2 OUTPUT -300mA WHITE GREEN (-)UNLOCK
27
