Specifications

40
Ozonic
Requirements/Setting up:
• Reason will automatically find the Ozonic if you click the Auto-de-
tect button on the Control Surfaces and Keyboards page in the
Preferences.
• To use Ozonic with Reason, you need to select bank A/preset 4 and
make sure this isn't changed from the factory settings. If needed,
you can restore your Ozonic to factory default settings by holding
down the Octave Up and Down buttons while turning the keyboard
on.
• We also recommend that you turn off Null mode on the Ozonic. This
is done by pressing the NULL button so that it isn't lit.
About the controls:
The keyboard (with aftertouch), mod and pitch wheels, nine faders, eight knobs
thirteen buttons, joystick and two pedals are available as control surface items in
Reason. For the joystick, each axis serves as two separate controllers, one regular
and one inverted.
About the default mapping:
• The transport buttons control the corresponding transport func-
tions in Reason.
• Buttons C38 and C39 are used for Target Previous/Next Track
(move the master keyboard input up or down in the track list).
• The Joystick X-axis is by default mapped to breath control. To make
use of this mapping, you need to set up the Reason device to use
breath control (possible with e.g. the Subtractor and NN-XT).
• The Joystick Y-axis doubles as mod wheel controller by default.
• On devices with patches, buttons C36 and C37 select previous/next
patch.
• On effect devices, button C40 typically controls the bypass/on/off
state.
D Mixer 14:2
There are four keyboard shortcut variations. In the first two, the faders and
knobs control levels and pans for channel 1-8 and channel 9-14 respectively.
In variation 3 and 4, the faders and knobs control Aux Send 1 and 2 for chan-
nel 1-8 and channel 9-14, respectively. Note that you can step between vari-
ations using buttons C32 and C33.
Fader C9 always controls the master level.
D Line Mixer 6:2
The faders always control the levels, with fader C8 controlling Aux Return
level and fader C9 controlling the master level.
The knobs control pan or Aux Sends, depending on the variation (selectable
with buttons C32 and C33).
D Thor
There are five variations: Filters, Osc & Amp, Modulation, Sequencer 1 and
Sequencer 2. The faders and knobs control parameters in the respective pa-
rameter groups for each of the variations. Buttons C32-C40 control the same
panel parameters in all variations.
D Subtractor
The faders, knobs and buttons control filters and envelopes, or oscillator pa-
rameters, depending on the selected keyboard shortcut variation.
Fader C9 always controls the master level.
D Malström
The faders, knobs and buttons control filters, oscillators or modulators, de-
pending on the selected keyboard shortcut variation.
Fader C9 always controls the master level.
D Redrum
By default only drum channel 1-8 can be controlled by the Ozonic.
The faders control drum levels, while the knobs control pitch, length or pan,
depending on the keyboard shortcut variation.
You can select patterns and banks with the following buttons: C32 (selects
pattern 1), C33 (steps through the patterns in the current bank), C34 (steps
through the banks) and C35 (controls the pattern enable switch).
Button C40 controls the Run button.
D BV512 Vocoder
The knobs control the main parameters while the faders control the band lev-
els. Which bands are controlled depend on the keyboard shortcut variation.
D Matrix Pattern Sequencer
You can select patterns and banks with the following buttons: C32 (selects
pattern 1), C33 (steps through the patterns in the current bank), C34 (steps
through the banks) and C35 (controls the pattern enable switch).
Button C40 controls the Run button.
D ReGroove
Faders C1-C4 control Groove Amount, knobs B10-B13 control Slide and
knobs B14-B17 control Shuffle for ReGroove channels A1-A4.