Specifications

13
D Thor
The buttons control the switch parameters in Thor. Lower Row Buttons 1 and
2 control front panel Buttons 1 and 2. Top Row Encoders 1 and 2 control
front panel Rotaries 1 and 2. The remaining Top Row Encoders control filter
parameters. The MIddle Row Encoders control Filter Env and Amp Env and
the Bottom Row Encoders control Osc and AMp parameters. Push Encoder
Group 1 control LFO, Portamento, Shaper, Delay and Chorus switch parame-
ters.
D Subtractor
The Bottom Row Encoders control Filter, FM, Osc Mix and Master Level pa-
rameters.
The Middle Row Encoders control Filter Env and Amp Env parameters.
The Top Row Encoders control Osc parameters.
Push Encoder Group 1 control LFO and Noise parameters.
The buttons control LFO, Osc, Filter, Noise and Modulation switch parameters.
D Malström
The Bottom Row Encoders control Filter, Shaper and Master Level parame-
ters.
The Middle Row Encoders control Osc B parameters.
The Top Row Encoders control Osc A parameters.
Push Encoder Group 1 control Filter parameters.
Push Encoder Group 1 Click control Filter switch parameters.
Push Encoder Group 2 control Modulator A parameters.
Push Encoder Group 2 Click control Modulator A switch parameters.
Push Encoder Group 3 control Modulator B parameters.
Push Encoder Group 3 Click control Modulator B switch parameters.
Push Encoder Group 4 control Oscillator and Velocity parameters.
The buttons control Osc, Shaper, Filter and Modulator switch parameters.
D Redrum
There are two keyboard shortcut variations: Play Mode and Pattern Select
Mode. In Play Mode, the upper row buttons can be used to audition drum
sounds and the lower row buttons are Mute buttons. In Pattern Select Mode,
buttons 1-6 on the upper and lower row select patterns and banks.
The Preset left/right buttons select which drum channels should be con-
trolled (drum 1-7 or drum 8-10). Bottom Row Encoder 8 always controls the
master level.
D MClass Stereo Imager
Bottom Row Encoders 1-3 control the continuous parameters and lower row
button 1 and upper row button 7 control the switch parameters.
Push Encoders 1:1 and 1:3 serve as Low and High Width meters.
D MClass Compressor
Bottom Row Encoders 1-5 and 8 control the continuous parameters. Push
Encoder 1:1 serves as Gain meter. Lower Row Buttons 1-3 and Upper Row
Button 7 control the switch parameters.
D MClass Maximizer
Bottom Row Encoders 1-5 control the continuous parameters. Push Encod-
ers 1:1 and 1:8 functions as Gain and Peak meters. Lower Row Buttons 1-4
and Upper Row Button 7 control the switch parameters.
D RV7000 Reverb
Bottom Row Encoders 1-4 control the RV7000 panel parameters. Buttons 1-
2 control the switch parameters.
Push Encoder Group 1 controls the soft knobs on the RV7000 Remote Pro-
grammer panel.
D BV-512 Vocoder
The band levels are controlled by the Middle Row Encoders. The Preset left/
right buttons select which bands should be controlled.
The Bottom Row Encoders and Lower Row Buttons 1-2 control the panel pa-
rameters.
Push Encoders control Mod level for the selected bands.
D RPG-8
Upper Row Buttons 1-8 control the panel switch parameters and the Top
Row Encoders 1-7 control the continuous panel parameters.
D Matrix
Buttons 1-6 on the upper and lower row select patterns and banks. Button 7
on the upper row controls the Pattern Enable switch. Foot Switch controls
Run.
D ReGroove
The Top Row Encoders control the A1-A8 Groove amount.
The Bottom Row Encoders control A1-A8 Shuffle.
The Middle Row Encoders control A1-A8 Slide.