Sedona Cart Assembly Instructions

ManualsBrandsLynx ManualsGrills24" Freestanding ProSear Grill

1 Part # 33807 Rev 2016

The following instrucons are provided to help you assemble the Sedona by Lynx™ cart.

IMPORTANT: Be sure to assemble on a so surface to prevent scratching the stainless steel.

Tools required: Regular phillips-head screwdriver, small crescent wrench and gloves.

Assembly Instructions:

SEDONA L400CART

L500CART

L600CART

& L700 CART

Introducon:

Your freestanding cart comes with all of the components necessary to assemble a cart for the Sedona by Lynx™ series of grills.

The Sedona by Lynx™ cart series is comprised of 8 sub assemblies:

1. Back Panel Assembly

2. Right Side Panel Assembly with Shelf

3. Le Side Panel Assembly with Shelf

4. Base Assembly with Wheels

5. Interior Shelf Assembly

6. Cross Brace Assembly

7. Right Door

8. Le Door (L600/700)

In addion there are 14 screws (¼-20x½) to assemble the cart and grill. There are also 4 screws with corresponding nuts

(#8-32 x 3/8) to aach the transformer assembly which is supplied with the grill.

Back Panel

Le Side Panel

Right Side Panel

Base Assembly

Cross Brace

Cabinet Door Frame

(L600/700)

Le Door

Right Door

Interior Shelf

Summary of content (5 pages)

PAGE 1
Assembly Instructions: SEDONA L400CART L500CART L600CART & L700 CART The following instructions are provided to help you assemble the Sedona by Lynx™ cart. IMPORTANT: Be sure to assemble on a soft surface to prevent scratching the stainless steel. Tools required: Regular phillips-head screwdriver, small crescent wrench and gloves. Introduction: Your freestanding cart comes with all of the components necessary to assemble a cart for the Sedona by Lynx™ series of grills.
PAGE 2
Step 1. Upon opening the box and identifying the components you will need 3 parts to begin assembly. You will need the back panel and the two side panels (L & R). Please note that you will need to have these parts upside down. On the side panels, there are some rivets attached to them. Those rivets will line up with the slots on the side of the back panel. You will need to push down the panel to lock it in place.
PAGE 3
On the frame there some notches where the base will slide into. Make sure the caster wheels sit above the frame of the cart. Use 4 1/4-20 x 1/2 screws to attach the base to the frame. Notches for Base Panel Notches for Base Panel Attach 4¼-20 x ½ Screws Here Step 4 Now turn the cart right side up to attach the inner shelves. For the L400 & L500 there is a Right triangle shelf with an electrical hole. For the L600 & L700 there is a full shelf with an electrical hole.
PAGE 4
Step 5 Cross Bar Notch Locate the cross bar and slide it into the slots on the front of the frame. On the L400/L500 the cross bar has magnets. On the ends of the cross bar you will see inserts for the screws to attach the bar to the frame. Use 2 1/4-20 x 1/2 screws to attach the cross bar to the frame. The hinges are attached to the side panel (if they are not visible ensure the panel is not facing the wrong direction). On the L600/L700 you will need to mount the door frame and cross bar at the same time.
PAGE 5
Step 6 A You will need a second person for this next step. Remove all packing materials from the grill. Remove the cooking grates, briquette trays, burners and warming rack to lighten the grill. You will need to place the grill onto the cart. The back of the grill needs to be set into the cart first. Then the front of the grill will slide into position after that. You may need to loosen 4 of the Screws inside the firebox. (See Step 7) We recommend wearing gloves while inserting the grill into the cart.