User Manual
Table Of Contents
- 1 Introduction
- 2 Getting Started Aurora(n)-USB
- 3 Getting Started Aurora(n)–TB3 (Thunderbolt)
- 4 Getting Started Aurora(n)-DNT (Dante)
- 5 Getting Started Aurora(n)-HD2 (ProTools HD)
- 6 Front Panel Controls
- 6.1 Meter Page
- 6.2 Function menu
- 6.2.1 Clock Setup
- 6.2.2 Line Trim
- 6.2.3 Preamp
- 6.2.4 Preamp Setup
- 6.2.5 Routing
- 6.2.6 Test Tone
- 6.2.7 Digital In Status
- 6.2.8 Optical Settings
- 6.2.9 SD Card
- 6.2.10 SD Record Setup
- 6.2.11 Sessions
- 6.2.12 Takes
- 6.2.13 Scenes
- 6.2.14 Playlists
- 6.2.15 Settings
- 6.2.16 Date & Time
- 6.2.17 Backlight
- 6.2.18 About
- 6.2.19 Firmware Update
- 6.2.20 USB Mode
- 6.3 Phones Source (Basic)
- 6.4 Phones Source (Advanced)
- 7 microSD Record and Play basics
- 8 Firmware Updates
- 9 Support
- 10 Troubleshooting & User Tips
- 11 Specifications
- 12 Aurora(n) Performance Measurements
- 13 Certifications
- 14 Warranty Information
45
8.3 Updating the LT-DANTE
The updater for the LT-DANTE is provided by the manufacturer of the Dante Brooklyn II chip, Audinate.
Because of this, the process is quite a bit different from the other LSLOT expansion cards as it relies upon a
third party updater program.
1. Prior to updating, ensure that Aurora
(n)
appears normally from the Dante Controller application.
2. Next, download the Brooklyn firmware update tool from:
https://www.audinate.com/products/firmware-update-manager
3. Then download the latest Dante firmware update file from www.lynxstudio.com > Support >
Downloads. Choose Aurora
(n)
> Firmware > Dante. Save this file to a convenient location on the
computer.
4. Launch the Audinate Firmware Updater.
5. Select the network adapter that is connected to the Dante network and press “Next”.
6. Press the “Update Dante Firmware” button.
7. Select the firmware update file downloaded in step 3, then press “Next”.
8. After a few seconds, the LT-DANTE should appear. Check the box next to the LT-DANTE you wish
to update.
9. Press Start. The “Ready” column will change to “Updating”.
10. When the updater is complete, close the Dante Firmware Update Manager. Power cycle Aurora using
the front panel power switch, wait three seconds, then turn the unit back on.
8.4 Updating the LM-DIG
The LM-DIG card has its own firmware update program that can be downloaded from the Lynx website.
1. Prior to updating, ensure that the Thunderbolt driver has been properly installed and is functional.
2. Visit www.lynxstudio.com
and click Downloads > Aurora
(n)
> Firmware
3. Download the current version of the LynxFirmware application for your computer platform
(Windows or macOS). Double Click to launch it.
4. Follow the prompts (Windows Users need to accept the EULA) until you reach the LynxFirmware
application main screen.
5. Look for the “LM-DIG in Module 4 of Aurora(n)” entry and verify that the “New Firmware
Revision” is higher than the “Current Firmware Revision”. If so, click on the Update button on that
line.
6. You will see the update status with a progress bar.
7. When the Update is complete, you will be instructed to power down the Aurora
(n)
. Turn off the front
panel power switch. Wait three seconds, then power it back up.
8.5 Update via microSD card
Please see Section 6.2.11 above for detailed instructions on how to update the Aurora
(n)
via the microSD card.
Updating via microSD card can update the firmware in following products:
Aurora
(n)
LM-DIG
LT-HD
LT-HD2