User manual

ManualsBrandsLUXVIEW ManualsCorded CCTV SystemsCCTV camera 3,6 mm

High-definition Analog Video Camera

(Built-in OSD)

USER’S MANUAL

Applicable for: AHD Standard Cameras, AHD Dome

Cameras, AHD Waterproof IR Cameras

Thank you for purchasing our products. Please read the manual

carefully before operating

Summary of content (22 pages)

PAGE 1
High-definition Analog Video Camera (Built-in OSD) USER’S MANUAL Applicable for: AHD Standard Cameras, AHD Dome Cameras, AHD Waterproof IR Cameras Thank you for purchasing our products.
PAGE 2
Safety Precaution This symbol means that there might exist uninsulated dangerous voltage inside the case, be careful of electric shock. This symbol reminds you to pay attention to important operation and maintenance instructions in the accompanied information. Warning  In order to prevent damage caused by fire or electric shock, please do not put cameras exposed in the moist environment or rainwater.
PAGE 3
yourself. Please contact our local distributor or our maintenance office authorized by our company, otherwise we won’t promise warranty.  Please do not splash water on the product components when cleaning. Notes Do not make the products under great impact or stay away from  strong electromagnetic interference and vibration. There are some sophisticated parts inside the camera, therefore,  during transportation and installation, please avoid the damage cause by stress or severe vibration.
PAGE 4
Contents I、OSD................................................................................... 5 1.1 LENS ...................................................................... 5 1.2 EXPOSURE..............................................................6 1.3 BACKLIGHT........................................................... 7 1.4 WHITE BAL............................................................ 9 1.5 DAY & NIGHT........................................................ 9 1.6 NR.......................
PAGE 5
Ⅰ、OSD Press the "OK" button, the camera will pop up the main menu system MAIN MENU 1. LENS 2. EXPOSURE 3. BACKLIGHT 4. WHITE BAL 5. DAY & NIGHT 6. NR 7. SPECIAL 8. ADJUST 9. EXIT MANUAL OFF ATW EXT SAVE & END 1.1 LENS There are 2 types of lenses, respectively: DC lens (DC drive lens), video camera (manual lens). Users can select the lens type according to the using of the camera. Press the "left" or "right" button on to choose the lens.
PAGE 6
Users can choose indoor mode & outdoor mode accordingly. Outdoor Mode OUTDOOR MODE 1. MIN SHU 1/25 2. MAX SHU 1/50 3. RETURN RET 1.2 EXPOSURE Move the cursor to "EXPOSURE"; press the "OK" button to enter the sub-menu. Press left-right key to set the relevant parameters of AGC & Brightness. Sens-up, D-WDR, DEFOG can also be set. EXPOSRURE 1. 2. 3. 4. 5. 6. 7. SHUTTER AGC SENS-UP BRIGHTNESS D-WDR DEFOG RETURN ---0-15 OFF 0-100 OFF OFF RET Sens-up has the two choices: "Auto", "OFF".
PAGE 7
SENS-UP 1. SENS-UP x2-x30 2. RETURN RET D-WDR has three options: auto, on and off. When D-WDR on, user can choose level between 0-8. D-WDR 1. LEVEL 0-8 2. RETURN RET 3. DEFOG has two options: off and auto. Choose auto to set. DEFOG 1. POS/SIZE 2. GRADATION 0-2 3. DEFAULT 4. RETURN RET 1.
PAGE 8
OFF, HSBLC". Users can select the appropriate backlight mode, according to the actual needs. Under BLC Mode, BLC level can set middle, low and high. BLC MODE 1. LEVEL Middle/HIGH/LOW 2. AREA 3. DEFAULT 4. RETURN RET HSBLC Mode, there are totally 4 select areas. Display can set on and off. Black mask can also set on and off. HSBLC level is from 0 to 100. HSBLC 1. SELECT AREA 1,2,3,4 2. DISPLAY ON/OFF 3. BLACK MASK ON/OFF 4. LEVEL 0-100 5. MODE ALL DAY/NIGHT 6. DEFAULT 7.
PAGE 9
NIGHT MODE 1. AGC LEVEL 0-255 2. RETURN RET 1.4 WHITE BAL White Balance is used to restore the authenticity of the scene; it is affected by scene color temperature change. Users can choose the corresponding white balance mode, according to the actual needs of the scene. They are: ATW/AWC->Set/Indoor/Outdoor/Manual/AWB. In Manual WB mode, the “Blue” and “Red” color can be adjusted from 0 to 100. MANUAL WB 1. BLUE 0-100 2. RED 0-100 3.
PAGE 10
enter "Auto Mode" sub-menu, you can set the corresponding parameters. AUTO Mode D&N AUTO 1. 2. 3. 4. 5. D->N (AGC) D->N (DELAY) N->D (AGC) N->D (DELAY) RETURN 0-255 0-255 0-255 0-255 RET Delay, with this setting the camera achieves the delay time of the transferring: color to black/white or black/white to color. Conversion between the colors is through controlling of the camera’s brightness sensor of the scene.
PAGE 11
B/W Mode B/W 1. BURST ON/OFF 2. IR SMART ON/OFF 3. IR PWM 0-100 4. RETURN RET When IR smart on, click “OK” button to enter the sub-menu of IR Smart. IR SMART 1. LEVEL 0-15 2. AREA 3. RETURN RET EXT MODE D&N EXT 1. D-N (DELAY) 0-60 2. N-D (DELAY) 0-60 3. RETURN RET Delay for both D->N and N->D could be adjusted from 0 to 60.
PAGE 12
in a state of users. On the choice of the value, do not set to the same value. The same value will lead to frequent switch under the light intensity changing. 1.6 NR In the "NR" menu click "OK" button to enter the sub-menu, you can set the corresponding parameters.
PAGE 13
SPECIAL 1. CAM TITLE ON 2. D-EFFECT 3. MOTION OFF 4. PRIVACY OFF 5. LANGUAGE ENG 6. DEFECT 7. RS485 8. RETURN RET CAMERA TITLE In the "camera title" menu, press the "left" "right" to select "On" At this point the camera image will display the name of executive function. Click "OK" button to enter the "CAMERA TITLE" setting sub-menu, you can set the camera name. You can set the camera code as numbers, uppercase letters, and related symbols. The length of the names is 15 characters.
PAGE 14
"Clear" is for removing the camera name. "Location" name for the set position. Through the "up, down, left, right" mobile name location, to determine a good location, then press "OK" button to return the name of the Edit menu. "End" is the end of the name edit to return to the previous menu. D-EFFECT D-EFFECT 1. 2. 3. 4. FREEZE MIRROR NEG.IMAGE RETURN ON/OFF OFF/MIRROR/V-FLIP/ROTATE OFF/ON RET When “FREEZE” set “ON”, the “MIRROR” function is not available.
PAGE 15
MOTION 1. SELECT AREA 1/2/3/4 2. DISPLAY ON/OFF 3. SENSTIVITY 0-100 4. COLOR RED/GREEN/BLUE/WHITE 5. IRANS 0.25/0.5/0.75/1.00 6. ALARM 7. DEFAULT 8. RETURN RET 9. ALARM can be set under motion mode, click “OK” button to enter the sub-menu. ALARM 1. VIEW TYPE ALL/OFF/BLOCK/OUTLINE 2. OSD VIEW ON/OFF 3. ALARM OUT ON/OFF 4. ALARM SIG HIGH/LOW 5. TIME 1-15 6. RETURN RET PRIVACY In the "PRIVACY" menu, press the "left" "right" to select "On".
PAGE 16
At this point the image will open the Privacy masking. Then, click "OK" to enter "privacy shield" setting sub-menu, you can mask the scope of privacy and sensitivity settings. PRIVACY 1. SELECT AREA 1,2,3,4 2. DISPLAY COLOR/OFF/MOSAIC/INV. 3. COLOR WHITE/BLACK/RED/BLUE/YELLOW/GREEN/CYAN/USER 4. TRANS. 1.00/0.25/0.50/0.75 5. DEFAULT 6. RETURN RET LANGUAGE English, Chinese(CHN1 & CHN2), German, French, Italian, Spanish, Polish, Russian, Portuguese, Dutch, Turkish, totally twelve language selections.
PAGE 17
LIVE DPC ON LIVE DPC 1. AGC LEVEL 0-255 2. LEVEL 0-255 3. RETURN RET WHITE DPC ON WHITE DPC 1. POS/SIZE 2. START 3. DPC VIEW OFF/ON 4. LEVEL 0-60 5. AGC 0-14 6. SENS UP x2,4,6,8,10,15,20,25,30 7. RETURN RET BLACK DPC ON BLACK DPC 1. POS/SIZE 2. START 3. DPC VIEW OFF/ON 4. LEVEL 0-100 5.
PAGE 18
RS485 Click “OK” button to enter the sub-menu. RS485 1. CAM ID 1-255 2. ID DISPLAY OFF/ON 3. BANDRATE 2400, 4800... 4. RETURN RET Please note the RS485 function is not available for the IR cameras. 8. ADJUST Click “OK” button to enter the sub-menu of “ADJUST”. Picture could be adjusted according to user. ADJUST 1. SHARPNESS AUTO/OFF 2. MONITOR LCD/CRT 3. LSC OFF/ON 4. VIDEO OUT PAL 5. RETURN RET Sharpness could be adjusted when choose the “AUTO” mode.
PAGE 19
SHARPNESS 1. LEVEL 0-10 2. START AGC 0-255 3. END AGC 0-255 4. RETURN RET Press the "left" "right" to select the monitor type: LCD & CRT. LCD LCD 1. GAMA USER/0.45-1 2. BLUE GAIN 0-100 3. RED GAIN 0-100 4. RETURN RET CRT CRT 1. BLACK LEVEL 0-60 2. BLUE GAIN 0-100 3. RED GAIN 0-100 4. RETURN RET 5.
PAGE 20
9. Exit After the parameter establishment completes, when it needs to preserve, choose “SAVE & END” and click “OK” button to save the changes. Camera will return to factory set if click the “RESET” button. If don’t want to save the changes, just choose the “NOT SAVE”, and click OK to Exit OSD menu.
PAGE 21
Ⅱ、Technical Specification Imaging Sensor Signal System Horizontal resolution Electronic Shutter S/N Ratio Video Output Minimum Illumination Day & Night Syn. System BLC Video Output Power Supply Operation Temperature Operation Humidity Lens Cable length 1.3 Megapixel CMOS PAL 720P PAL：1/50～1/100000s More than 52dB 1.0Vp-p, 75 ohms 0.01 Lux/F1.2, 0 Lux with IR ICR Internal BLC/OFF/HSBLC BNC DC12V -200C～+500C 10%~90%RH 3.6mm 0.
PAGE 22
III、FAQ 1. Q: No image after installation? a. Check to connect the power supply correctly, whether the indicating led is always on or not; b. Check the video cable, make sure it is workable; c. Check if the monitor has been open. 2. Q: Image interference after installation a. Check the power quality, if the adapter can’t work, please replace another one. b. Check if electromagnetic interference exists in the surroundings, please use some anti-interference devices. 3. Q: The image color is abnormal. a.