Owners Manual Studio Series Congratulations On Your New Spa! Luxury Spa USA Call us at 866-220-7405
Before enjoying your new Luxury Spas hot tub, please follow these important steps 1- Before filling the hot tub, remove the plastic cover from the filter. The filter is located in the sanitary basket. Check to make sure there no other debris are inside the sanitary basket. 2- Make sure your hot tub is hooked to the correct voltage and amperage for your model hot tub. All Luxury Spas hot tubs are 240V. You can find the correct amperage for your model listed in the included User Guide.
Table of Contents Safety Informa�on ................................................................................................ 2 Safety Instruc�ons ............................................................................................... 3 Preparing For your New Spa .................................................................................. 5 Spa Models + Electrical Requirements ................................................................. 6 Electrical Install ........................
Important Safety Instructions and Warnings READ AND FOLLOW ALL INSTRUCTIONSNS ! To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. Warning: Children should not use spas or hot tubs without adult supervision. Avertissement: Ne pas laisser les enfants utiliser une cuve de relaxation sans surveillance. ! Warning: Do not use spas or hot tubs unless all suction guards are installed to prevent body and hair entrapment.
Important Safety Instructions and Warnings READ AND FOLLOW ALL INSTRUCTIONS ! To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. Warning: Prolonged immersion in a spa or hot tub may be injurious to your health. Avertissement: L’utilisation prolongee d’ une cuve de relaxation peut etre dangereuse pour la sante. ! Warning: Do not permit or use electric appliances (such as a light, telephone, radio or television) within 1.
Preparing for your New Spa Consider Spa Use Permitting Most cities and county's require permits for exterior construction and electrical circuits. In addition, some communities have codes requiring residential barriers such as fencing and/or self-closing gates on property to prevent unsupervised access to the property by children. Your local inspections office can provide information on which permits may be required and how to ob-tain them prior to the delivery of your spa.
Filter Removal Upon receiving your Spa, you'll need to remove the filter and the plastic that covers it. Upon doing so, check the Sanitation basket to assure there is no remaining plastic that could have gotten lodged during shipping. To access the filter, remove top cover(1), and rotate the filter housing (2) to access the filter(4). Photo 5 shows the bottom sanitation basket, please assure this is clear of any debris.
240 Volt Electrical Installation ! Warning: The electrical circuit must be installed by an electrical contractor and approved by a local building or electrical inspector. Failure to comply with state and local codes may result in fire or personal injury and will be the sole responsibility of the spa owner. Improper installations present hazards which can result in personal injury or property damage and void the warranty on the spa.
Luxury Spa's Electrical Components *Note: A GFCI circuit is required. Using the suggested size will ensure proper operation. Call Customer Service for any additional questions 866-220-7405.
Prepare for Your New Spa GFCI Wiring Diagram ! (North America 240V 60hZ) WARNING: The electrical circuit must be installed by an electrical contractor and approved by a local building or electrical inspector. Failure to comply with state and local codes may result in fire or personal injury and will be the sole responsibility of the spa owner. Customer must provide a disconnect in the fixed wiring.
SPA FEATURES 1.) All electronic features of the spa except the Bluetooth are controlled by the control pad. 9) Spa Drain allows you to drain the spa quickly for changing out the water. 2 ) Air adjuster handles let you adjust the amount of pressure at the designated jets by turning the handle left or right. 10) Water intake grates allow water circulation through the motor and heater and out through the jets.
Water Quality and Maintenance Testing and Adjusting Water Chemistry - Before using your spa, it is important to test the water so that it maintains the correct chemical balance. This will ensure water quality, clarity and help keep your spa equipment in good condition. - You will need to test and adjust the chemical balance of your spa water. Although this is not difficult, it needs to be done regularly.
Sanitation Balancing the pH Level - The pH level is the measure of the balance between acidity and alkalinity. - The recommended pH is 7.2 - 7.6. - If the pH is too low, it can cause corrosion of metal fixtures and the heating element. - If the pH is too high, it can cause scaling by allowing metals or minerals to form deposits and stain spa surfaces. Too alkaline, causes scaling Ideal balance Too acidic, causes corrosion. Ozone 8.2 8.0 Decrease the pH level. 7.8 7.6 7.4 7.2 7.0 6.
! The manufacturer does hereby claim no responsibility or liability for use of and quantities of the chemicals used. Read and follow all label instructions. Filtration Cleaning your filter regularly is the easiest and most effective single thing you can do to keep your water clear. A clogged or dirty filter will cause the heater and pump to work harder than they need to, possibly causing them to fail. The spa’s heating system will only function with the proper amount of water flow through the system.
Draining Your Spa Pillow Care and Removal Your spa should be drained every 3-4 months, and refilled with fresh tap water. The following is the recommended method for draining your spa. 1. Turn off the power at the breaker. 2. Remove filter. 3. Your drain valve is located outside corner of the Service Access Side. 4. Rotate the cap and pull until you feel it give, then pull the plug two notches out. 5. Once the drain plug is external, hook up the female end of the garden hose. 6.
! Vacation Care You can leave your spa unattended for up to two weeks if you follow these instructions. - ALWAYS lock your cover using the cover locks if you plan to be away from home and the spa is filled with water. - Shock the water (add either chlorine or bromine sanitizer). - When you return, check water chemistry and adjust accordingly. - If you will not be using your spa for longer than 14 days and a spa maintenance service is not available, we strongly recommend you drain and winterize your spa.
Filter Replacement Guide Luxury Spa USA Page 16 Call us at 866-220-7405
Now that you know the basics, let us show you how to set up your new Luxury Spa Keypad Luxury Spa USA Page 17 Call us at 866-220-7405
Studio Series Display User Guide Questions? Call 866.220.
Programming your Spa Note: Prior to operating your spa, it is important to program your spa to ensure all functions operate correctly. 1. Changing Celsius to Fahrenheit 1.1 When the control system is powered on, you can change the temperature from C* to F* by holding the programming key for 5 seconds. 2. SETTING THE WATER TEMPERATURE 2.1 When the system is on but not in programming mode, you can adjust the water temperature by pressing the up/down buttons. 3.
CLOCK INTERFACE 3.1 When the system is powered on, press the and the LCD will flash the HR character. You can then adjust the hour by pressing the up/down buttons. 3.2 Press the programming button again to cycle over to the minute setting. You can then adjust the hour by pressing the up/down buttons. 4 SETTING WATER CIRCULATION TIME In order for the water circulation cycle to operate correctly the clock must be set first.
4.3 If your spa is not equipped with the optional circulation pump, pressing the pump button twice will put the pump in low mode to circulate the water when the power is on. Base System, Features and Functions Water Pump - Use this button to turn the pump on/off. The water pump will turn off automatically after 30 minutes. Air Pump - Use this button to turn the optional air pump on/off. The air pump will turn off automatically after 30 minutes.
Heating - When the water temperature is below the set temperature, the heater will come on and the control system will power on at the same time. The heater will stop once the water reaches the set temperature. Refer to “Setting The Temperature” in the settings section. Anti-Freezing Protection - Your spa is equipped with anti-freeze protection. If the water temperature drops to less than 6 *C (43 *F) the heater will turn on automatically until the water temperature reaches 10 *C (50 *F).
ERROR CODE TROUBLESHOOTING FAULT FAULT CODE MESSAGE E1 HOW TO FIX Temperature sensor Please check the temperature sensor and its connection and fault replace it if necessary. The control system detected that the temperature of the temperature sensor was too high. When the heater is started, this failure may occur when there is no water in the E2 The temperature is beyond the normal range water pipe or the flow is small during heating. Please ensure that there is water in the SPA .
Indicator Lights and what they mean Water Pump Air Pump Heater Light Circulation Pump Water Pump Indicator Arrows LED Lights Air Pump(If Equipped) Programming Button Luxury Spa USA Page 25 Call us at 866-220-7405
Luxury Spas USA Warranty This warranty covers all Luxury Spas USA branded hot tubs which are purchased directly from Luxury Spas USA Ltd. This warranty certificate is non-transferable. Shell Warranty - 10 years Luxury Spas USA warrant the shell against water loss to the customer arising from structural failure for a period of 10 years.
is sent out and discovers there is no issue, or the issue is not manufacturing related, then customer will be responsible for the service call. If a manufacturing related issue is discovered there is no charge for the technician visit. If the technician determines that any fault is not covered under this warranty, the customer is solely responsible for the cost of any parts and or labor charges.
