Simply Connected Quick Install Guide XWR-1750 Dual Band Wireless AC1750 Gigabit Router Use the XWR-1750 to: Deliver Next Generation 802.11ac Gigabit Wi-Fi with Speeds up to 1750Mbps Maximize Data Rates with Concurrent Dual-Band (2.
XWR-1750 Quick Install Guide DUAL BAND WIRELESS AC1750 GIGABIT ROUTER Model Number: XWR-1750 FCC ID: W59XWR1750 Quick Install Guide © 2013 Luxul. All Rights Reserved. No part of this publication may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this manual is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design.
Simply Connected PACKAGE CONTENTS The following items should be included in the box: XWR-1750 Dual Band Wireless AC1750 Gigabit Router 3 Dual Band RPSMA Male Antennas Ethernet Cable Power Adaptor Quick Installation Guide NOTE: If any of the listed items are missing or damaged, please contact the reseller from whom you purchased for return/replacement.
XWR-1750 Quick Install Guide Rear Panel XWR-1750 Rear Panel View Antenna Ports: 3 RPSMA female antenna ports to connect the included antennas Power Input: Power adapter included NOTE: To hard reboot the router, remove the power adapter. Wait 10 seconds and re-apply power. USB 1 -2 Ports: 2 USB 2.
Simply Connected PREPARING FOR INSTALLATION System Requirements Computer supporting TCP/IP and equipped with a Web browser. Supported Web browser versions include I.E. 9.0, Firefox 3.6, Safari 5.0, Chrome 6.0, Opera 10.6 and up. The Web browser is used to configure the XWR-1750. Power must be AC 100-240V~ 1.0A 50/60Hz.
XWR-1750 Quick Install Guide CONFIGURATION Default IP Address The XWR-1750 default IP address is 192.168.0.1. This address can be changed. However, for hassle free installation of other XenConnect™ plug and play Luxul devices, it is recommended that the default IP value be maintained. Parameter: Default IP address: Default user name: Default password: Default Value 192.168.0.1 admin admin Connect a Client Device Use a computer or mobile device to connect via Ethernet or wireless to the XWR-1750.
Simply Connected WPS CONFIGURATION/RESET BUTTON Used to configure WPS (Wi-Fi Protected Setup) or restore factory default settings To configure WPS, press and hold the WPS/Reset button until the WPS LED turns on (typically about 5 seconds). The XWR-1750 is now in WPS pairing mode. Follow the pairing instructions for your client device and enter the XWR-1750 WPS pin number (12345678) when prompted.
XWR-1750 Quick Install Guide MOUNTING PATTERN 8 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 luxul.
Simply Connected © 2013 Luxul. All Rights Reserved.
XWR-1750 Quick Install Guide WARNINGS AND SAFTY INFORMATION Read all installation instructions and site survey reports, and verify correct equipment installation before connecting the XWR-1750 to its power source. Verify that the electrical circuits have appropriate grounding and overload protection. Attach only approved power cords to the device. Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications.
Simply Connected Safety in Hospitals: Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected. RF Exposure Guidelines Safety Information: The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
