Simply Connected Quick Install Guide XAP-1230 High Power Wireless 300N Commercial Grade Access Point Use the XAP-1230 to: Deliver Broader Wi-Fi Coverage and Eliminate Client Device Roaming Issues with Fewer APs Improve Data Rates with Multi-Stream Wireless 802.
XAP-1230 Quick Install Guide Quick Install Guide Model Number: XAP-1230 High Power Wireless 300N Commercial Grade Access Point FCC ID: W59XAP1230A IC: 8584A-XAP1230 © 2014 Luxul. All Rights Reserved. No part of this publication may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this manual is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design.
Simply Connected PACKAGE CONTENTS One: XAP-1230 Wireless Access Point Two: 5dBi Dipole Antennas One: PoE Injector and Power Cord One: Ethernet Cables Four: Rubber Feet One: Quick Install Guide NOTE: If any of the listed items are missing or damaged, please contact the reseller from whom you purchased for return/replacement. HARDWARE DESCRIPTION The XAP-1230 high powered access point is designed for optimal performance as well as for simple and efficient installation and setup.
XAP-1230 Quick Install Guide XAP-1230 LED Indicators Indicator Name Description Power On The power is on Off No power, check power connections On There is an active Ethernet connection Flashing Indicates Ethernet activity Off There is no active Ethernet connection On The wireless radio is active and wireless access is enabled Off The wireless radio is not active and wireless access is disabled On Bridge is connected Flashing Bridge Mode enabled but not connected Off The AP is in defa
Simply Connected Back Panel The back of the XAP-1230 provides two SMA antenna connectors and one RJ-45 connection that is used to deliver both power and data to the access point. RESET XAP-1230 Rear Panel Reset Button: The Reset button is used to clear the current settings of the XAP-1230 and restore factory default settings. To Restore the Default Settings: With the XAP-1230 powered on, press and hold the Reset button for 15 seconds.
XAP-1230 Quick Install Guide XAP-1230 INSTALLATION Access Point Placement This XAP-1230 uses omni-directional antennas designed to provide 360 degrees of coverage. For maximum efficiency, it should be placed as close as possible in the center of the area in which you would like to provide coverage. XAP-1230 Coverage Pattern Mounting the Access Point on a Wall The XAP-1230 can be mounted directly to a wall. It can also be placed on a desktop, shelf, or other flat surface.
Simply Connected Install Included Rubber Feet in the Impressions in the bottom of the XAP-1230 Connecting the Ethernet Cable With the XAP-1230 properly mounted and the Antennas installed, you can now plug the Ethernet Cable into the RJ-45 connector. NOTE: Category-5, super Category-5 or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP) cables can be used. For best results, it is recommended that Category-6 shielded twisted pair be used to ensure stable data transmission at highest data rates.
XAP-1230 Quick Install Guide POE Injector XAP-1230 Power Source DATA & PWR OUT DATA IN From your Router or Switch The PoE Injector combines power and data to the XAP-1230 CONFIGURATION Default IP Address The XAP-1230 is not equipped with internal DHCP server. If connected to a Luxul Router, configuration will be automatic. Otherwise, the IP address of the computer for login and configuration will need to be manually configured. The table below lists the default parameters of the XAP-1230.
Simply Connected NOTE: Go to http://luxul.com/how-to-videos for videos about changing the IP address of your Operating System. Connect a Client Device Connecting a Wireless Client Device: Connect the client device to the XAP-1230 default wireless network LuxulXen1200. This wireless network will run in Open Security mode. A passphrase is not required until Wireless Security is configured. Login Login to the XAP-1230 with the following steps: 1. Open a Web browser, and enter 192.168.0.10.
XAP-1230 Quick Install Guide Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications. The XAP-1230 is designed for indoor use only. DO NOT place this outdoors. DO NOT install in or near hot or humid places, such as a kitchen or bathroom. Take care to minimize exposure to excessive heat or moisture. Small parts and plastic bags used for packaging may be harmful to small children.
Simply Connected When servicing the equipment and selecting a location for the antennas, it is important to note that a minimum distance of 20cm is required between personnel and the device or antenna to comply with the radio frequency exposure limit. The antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
This radio transmitter with the model:Q5003 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
