Specification

ManualsBrandsluxier ManualsBathSingle-Handle 1-Spray Shower Faucet with Valve in Matte Black (Valve Included)

1 SS-B01 Rev. F 072021

Luxier

SS-B01-TB (Brushed Nickel)

SS-B01-TC (Chrome)

SS-B01-TM (Matte Black)

SS-B01-TO (Oil Rubbed Bronze)

Rainfall Shower System

Specications:

Shower head ow rate: maximum 1.8 gpm at 80 psi

Plumbing connection: standard 1/2” pipe tting

IMPORTANT!

• Read and understand this instructions completely before installation. Failure to follow these

instructions could prevent the valve from working properly. Consult a professional installer if needed.

• This installation guide is subject to change without notice, please contact us to request the most

updated version of this installation guide.

• This is a general installation guideline, actual installation may vary. It is recommended the

installation is performed by a trained and experienced installer.

• Please follow all local building and plumbing codes.

• Proper pressure must be maintained for the pressure balance valve to work properly. Make sure

water pressure is about the same on both hot and cold water side.

• Product drawings in this installation guide is for illustration purpose only. Actual product may vary

depends on model.

• Always take extra precautions and wear appropriate safety equipment when installing this product.

• Unpack and inspect the parts from the package for shipping damage and make sure all parts are

included in the package. Keep the product in its package until you are ready to install.

• Make sure the installation site is clean and free of dust and debris.

Summary of content (7 pages)

PAGE 1
Rainfall Shower System SS-B01-TB (Brushed Nickel) SS-B01-TC (Chrome) SS-B01-TM (Matte Black) SS-B01-TO (Oil Rubbed Bronze) Specifications: Shower head flow rate: maximum 1.8 gpm at 80 psi Plumbing connection: standard 1/2” pipe fitting IMPORTANT! • Read and understand this instructions completely before installation. Failure to follow these instructions could prevent the valve from working properly. Consult a professional installer if needed.
PAGE 2
Thank you for purchasing Luxier products. Please read the information below and keep this installation guide for future reference. If you require assistance, please contact our customer service department at 1-877-711-8828, Monday - Friday 9AM - 5PM Pacific Time or by email at support@luxierusa.com. Limited Lifetime Warranty (For USA Only) The manufacturer warrants this product to be leak and drip free during daily normal household use for as long as it is owned by the original purchaser of this product.
PAGE 3
Parts Diagram & Dimensions 17 3 2 18 16 1 19 20 21 22 4 8 9 10 13* 5 11 12 14* 15* 7 6 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 Shower Head Shower Arm Flange Valve Body Rubber Gasket Cap Hot Water Stop Valve Assembly Cold Water Stop Valve Assembly Pressure Balance Cartridge Cartridge Nut Stem Extension Threaded Nipple Protective Cover* Temporary Screws* Protective Sleeve* Escutcheon O-Ring Handle Plunger Spring Screw Stop Valve Nut 13 1/4” 1/2” NPT 4 1/2” 7 7/8”
PAGE 4
Installation 1. Position valve body in the wall. It is recommended the valve to be about 48” above the finished floor and shower outlet to be about 30” above the valve (Fig. A1) The finished wall should be set between the markers on the temporary protective cover. The recommended depth is 2 11/16” to 3 7/16”. (Fig. A) Make sure the UP outlet is pointed upward. (Fig. B) NOTE: Valve access hole on the wall should be 6” in diameter and outlet hole for shower arm is about 1 1/4” in diameter.
PAGE 5
Installation (Cont.) 5. Remove and discard the protective sleeve (15) and cover (13) from the valve. Slide the escutcheon onto the valve as shown in Fig. E. Place the handle assembly on the stem extension and turn the handle clockwise to install the handle. If there is a gap when the handle is attached to the valve measure and write down the distance of the gap between the handle and the escutcheon plate as shown in Fig. E1. E1 E X 15 13 6. Remove the handle and the escutcheon plate and set them aside.
PAGE 6
Operation 1. Turn the handle counter-clockwise from the OFF position to the BLUE dot (cold water) to start the water flow. Continue turning the handle to the RED dot (hot water) to reach the hot water temperature. (CAUTION: Scalding may occur if the control is set to maximum temperature.) It is strongly recommended to set the handle halfway between the BLUE and RED dots as the starting point. Gradually turn the handle to set the desired water temperature. HOT (red) COLD (blue) 2.
PAGE 7
Service the Valve and Pressure Balance Cartridge NOTE: To maintain the performance of the shower valve. It is recommended to clean the pressure balance cartridge at least once a year. More frequent cleaning is needed if the water has high mineral content. 1. Remove shower trims (#16, #17, #18) 2. Turn off water supply at the stop valves (#7 and #8) by using a large flat head screwdriver and turn the valve clockwise to shut off the water. 3.