Measurement Guide

ManualsBrandsLuxier ManualsBathSingle-Handle 1-Spray Shower Faucet with Valve in Brushed Nickel (Valve Included)

SS-B01Rev. D 012019Luxier

SS-B01-TB (Brushed Nickel)

SS-B01-TC (Chrome)

SS-B01-TM (Matte Black)

SS-B01-TO (Oil Rubbed Bronze)

Rainfall Shower System

Pressure Balance Valve and Shower Trim Installation

IMPORTANT!

• Read and understand this instructions completely before installation. Failure to follow these

instructions could prevent the valve from working properly. Consult a professional installer if needed.

• This installation guide is subject to change without notice, please contact us to request the most

updated version of this installation guide.

• This is a general installation guideline, actual installation may vary. It is recommended the

installation is performed by a trained and experienced installer.

• Please follow all local building and plumbing codes.

• Product drawings in this installation guide is for illustration purpose only. Actual product may vary

depends on model.

• Always take extra precautions and wear appropriate safety equipment when installing this product.

• Unpack and inspect the shower panel from the package for shipping damage and make sure all parts

are included with the shower panel.

• Keep the product in its package until you are ready to install.

• Make sure the installation site is clean and free of dust and debris.

• Please make sure the water supply is shut o to the installation area. If necessary, shut o the

water to the entire house.

• Turn on the water at a bathroom faucet in the house to relieve the pressure in the plumbing system.

Tools and Materials Needed:

1. Safety Glasses

2. Teon (PTFE) Tape

3. Plumber’s Putty and Caulking

4. Tube Cutter

5. Adjustable Wrench

6. Screwdriver Sets

7. Tourch

8. Hacksaw

9. Marker

Specications:

Shower head ow rate: maximum 1.8 gpm at 80 psi

Plumbing connection: standard 1/2” pipe tting

Summary of content (5 pages)

PAGE 1
Rainfall Shower System Pressure Balance Valve and Shower Trim Installation SS-B01-TB (Brushed Nickel) SS-B01-TC (Chrome) SS-B01-TM (Matte Black) SS-B01-TO (Oil Rubbed Bronze) Specifications: Shower head flow rate: maximum 1.8 gpm at 80 psi Plumbing connection: standard 1/2” pipe fitting Tools and Materials Needed: 1. Safety Glasses 2. Teflon (PTFE) Tape 3. Plumber’s Putty and Caulking 4. Tube Cutter 5. Adjustable Wrench 6. Screwdriver Sets 7. Tourch 8. Hacksaw 9.
PAGE 2
Thank you for purchasing Luxier products. Please read the information below and keep this installation guide for future reference. If you require assistance, please contact our customer service department at 1-877-711-8828, Monday - Friday 9AM - 5PM Pacific Time or by email at support@luxierusa.com. Limited Lifetime Warranty (For USA Only) The manufacturer warrants this product to be leak and drip free during daily normal household use for as long as it is owned by the original purchaser of this product.
PAGE 3
Parts Diagram & Dimensions 3 2 17 1 18 16 4 8 9 10 13* 5 11 12 14* 15* 7 6 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 Shower Head Shwoer Arm Flange Valve Body Rubber Gasket Cap Stop Valve Stop Valve Pressure Balance Cartridge Cartridge Nut Stem Extension Threaded Nipple Protective Cover* Temporary Screws* Protective Sleeve* Escutcheon O-Ring Handle 13 1/4” 1/2” NPT 2 1/2” 4 1/2” 7 7/8” 3” 7 5/16” * will not be used in final installation * Drawings not to Scale.
PAGE 4
Installation 1. Position valve body in wall. It is recommended the valve to be about 48” above the floor and shower outlet to be about 30” above the valve (Fig. A1) The finished wall should be set between the markers on the temporary protective cover. The recommended depth is 2 11/16” to 3 7/16”. (Fig. A) Make sure the UP outlet is pointed upward. (Fig. B) NOTE: Valve access hole on the wall should be 6” in diameter and outlet hole for shower arm is about 1 1/4” in diameter.
PAGE 5
Installation (Cont.) 5. Remove and discard the protective sleeve (15) and cover (13) from the valve. Slide the escutcheon onto the valve. Attach the handle (18) as shown in Fig. E. Place the handle assembly on the stem extension (12) and turn the handle clockwise to install the handle. If there is a gap when the handle is attached to the valve measure and write down the distance of the gap between the handle and the escutcheon plate as shown in Fig. E1. E1 E X 15 13 6.