Luxier SP037-SS Features - Stunning stylish European inspired design - Durable stainless steel frame construction - Square stainless thin profile shower head - Fingerprint resistance finish - 4 stage shower functions (Rainfall, Massage Spray, Hand Shower, Tub Spout) - Contemporary brass hand shower - Tempered glass shelf Luxier 1 SP37-SS Rev.
Thank you for purchasing Luxier products. Please read the information below and keep this installation guide for future reference. If you require assistance, please contact our customer service department at 1-877-711-8828, Monday - Friday 9AM - 5PM Pacific Time. Or by email at support@luxierusa.com.
Attention • This installation guide is subject to change without notice, please contact us to request the most updated version of this installation guide. • This is a general installation guideline, actual installation may vary. Consult a professional if necessary. • Product drawings in this installation guide is for illustration purpose only. Actual product may vary depends on model. • Always take extra precautions and wear appropriate safety equipment when installing this product.
Fig. A * Shower panel drawing on this page is for illustration purpose only. Actual product may vary depends on model. Recommended 10” - 12” It is recommened to aim the top horizontal body jets at the chest area of the user for optimal showering experience. The installation height of the outlet box is approximately the total distance of measurement A and measurement B. Approximate shower inlet valve location approx.
Technical Data Recommended Operating Pressure: 50-80 PSI 355mm 13.98” 70mm 2.76” 180mm 7.09” 1,400mm 55.11” 815mm 32.09” 550mm 21.65” 315.5mm 12.42” 54mm 2.13” 206.5mm 8.13” *All Measurements are Approximate Luxier 5 SP37-SS Rev.
Parts List 1 2 7 8 9 3 16 17 18 4 5 10 12 11 13 01. Shower Arm 02. Rubber Gasket 03. Shower Head 04. Glass Shelf 05. Shower Panel Body 06. Tub Spout 07. Locking Nut 08. Rubber Washer 09. Rainfall Shower Supply Connector 10. Hand Shower Supply Connector 11. Rubber Gasket 12. Hand Shower 13. Hand Shower Cradle 14. Rubber Gasket x 2 15. Hand Shower Hose 16. Screw x 4 17. Mounting Bracket x 2 18. Wall Anchors x 4 Luxier 14 15 6 6 SP37-SS Rev.
Installation 1. Attach shower arm assembly to the panel body. Make sure to install screen washer to protect shower head from debris in the plumbing system. 2. Install hand shower cradle (1) to the shower panel by installing the rubber washer (2) and the locking nut (3) and attach white plastic hose tube connector (5) with PVC tubing to complete the connection. (NOTE: Make sure the silicon gasket (4) is seated properly inside the connector.) 2 3 4 5 1 3.
Installation (cont.) 4. Using a drill with a tile bit, drill the hole slowly into the tile. Do not drill into any piping or wiring in the wall. Insert the anchors into the wall. 1” 5. Secure the mounting brackets to the wall. Luxier 8 SP37-SS Rev.
Installation (cont.) 6. Apply thread sealant tape to the threading on the shut off valves before connect both hot and cold water supply hoses to the valves. IMPORTANT : - Make sure the water supply hoses are connected to the corresponding valves i.e. cold water hose to the cold water valve and the same for hot water hose. The mixing valve will not function properly if the hoses are installed incorrectly. - Before hanging the shower panel on the wall.
Installation (cont.) 8. Attache shower head. Apply some (NOTE: PTFE tape on the thread to prevent leaking) 9. Connect hand shower hose to the main panel body and connect the hand shower wand to the hose. Make sure the silicon gaskets are seated properly to prevent water leak. 10. Loosen the set screws under the anchors to insert the glass shelf. Tighten the set screws to secure the glass shelf. (WARNING: Do not place heavy objects on the glass shelf.
Operation Function Selector Temperature Control 1. Turn the temperature control knob to set the desired water temperature. The control is preset to maximum temperature of 100.4 degrees Fahrenheit. To set higher water temperature, push down the safety pin and turn the dial counterclockwise to the desired temperature mark. (Important: Scalding may occur if bypass the safety pin, use this control with caution) 2. Select the desired water function by turning the selector to the corresponding marking.
