Luxier SP25-SS Features • • • • • Stunning stylish European inspired design Elegant & Durable stainless steel frame construction Pressure balanced valve minimize the chance of scalding. 4 stage shower functions (Rainfall, Waterfall, Massage Spray, Hand Shower) 50 total rainfall nozzles and 4 adjustable horizontal spray massage jet pads with 24 nozzles on each pad Luxier 1 SP25-SS Rev.
Thank you for purchasing Luxier products. Please read the information below and keep this installation guide for future reference. If you require assistance, please contact our customer service department at 1-877-711-8828, Monday - Friday 9AM - 5PM Pacific Time. Or by email at support@luxierusa.com.
Attention • This installation guide is subject to change without notice, please contact us to request the most updated version of this installation guide. • This is a general installation guideline, actual installation may vary. Consult a professional if necessary. • Product drawings in this installation guide is for illustration purpose only. Actual product may vary depends on model. • Always take extra precautions and wear appropriate safety equipment when installing this product.
Fig. A * Shower panel drawing on this page is for illustration purpose only. Actual product may vary depends on model. Recommended 10” - 12” It is recommened to aim the top horizontal body jets at the chest area of the user for optimal showering experience. The installation height of the outlet box is approximately the total distance of measurement A and measurement B. Approximate shower inlet valve location approx.
Technical / Flow Rate Data Recommended Operating Pressure: 50 - 80 psi 200mm 7.87” 495mm 19.49” 1500mm 59.06” 770mm 30.31” 570mm 22.44” 365mm 14.37” 260mm 10.24” 72.5m 2.85 ” *All Measurements are Approximate Luxier 5 SP25-SS Rev.
Parts List 1 10 9 8 3 2 4 5 6 7 01. Shower Panel Body 02. Hand Shower 03. Hand Shower Cradle 04. O rings 05. Hand Shower Hose 06. Gasket 07. Hand Shower Water Connector 08. Screws X 4 09. Mounting Brackets X 2 10. Wall Anchors X 4 Luxier 6 SP25-SS Rev.
Installation 2 3 4 1 5 1. Install hand shower cradle (1) to the shower panel by installing the rubber washer (2) and the locking nut (3) and attach white plastic hose tube connector (5) with PVC tubing to complete the connection. (NOTE: Make sure the silicon gasket (4) is seated properly inside the connector.) 2. Mark the positions of the 2 brackets on the wall and prepare the tile wall for drilling. Use a piece of painters tape or masking tape over the drill area to prevent damages to the tiles.
Installation (cont.) 4. Secure the mounting brackets to the wall. 5. Apply thread sealant tape to the thread- ing on the shut off valves before connect both hot and cold water supply hoses to the valves. IMPORTANT : - Make sure the water supply hoses are connected to the corresponding valves i.e. cold water hose to the cold water valve and the same for hot water hose. The mixing valve will not function properly if the hoses are installed incorrectly. - Before hanging the shower panel on the wall.
Installation (cont.) 6. Once the shower panel has been tested for functions and leaks. Hang the unit on the wall to complete the installation. Due to the limited space behind the shower panel, do not bend the hoses. Any restrictions in the water supply hoses will greatly reduce the performance of the shower panel. After the shower panel is set properly on the wall, apply silicon sealant on both sides of the shower panel to prevent the unit from moving. (NOTE: Do not seal the bottom of the panel.) 7.
Operation 1. Turn the temperature control knob counter-clockwise to set the desired water temperature. The control starts with cold temperature and goes to warm and hot as the knob Function Selectors is turned counter-clockwise (Important: Scalding may occur if the control is set at high temperature, use this control with caution) 2. Select the desired water function by turning the selector to Temperature Control the corresponding marking.
