Full Product Manual

ManualsBrandsLUXIER ManualsBathModern Freestanding Single-Handle Floor-Mount Roman Tub Faucet Filler with Hand Shower in Oil Rubbed Bronze

FTF01 Rev.3.1 01/2021

Luxier

Model Number:

FTF01-TB (Brushed Nickel)

FTF01-TC (Chrome)

FTF01-TM (Matte Black)

FTF01-TO (Oil Rubbed Bronze)

Features:

- Brass and Zinc Alloy Construction

- Single Hole Installation

- Drip Free 40 mm Ceramic Cartridge

- Hand shower ow rate 1.8 gpm at 80 psi

- Tub spout ow rate 3.7 gpm at 20 psi

- Rough-in kit included

- Complies with:

IAPMO / UPC / cUPC

ADA

Freestanding Floor Mount Bathtub Filler

32”

38 1/8”

27 3/4”

43 1/16”

8 1/8”

5 1/2”

1 3/4”

2”

3 1/2”

4 1/4”

1/2” NPT

G3/8

* Drawings not to Scale. All Measurements are Approximate *

Summary of content (7 pages)

PAGE 1
Freestanding Floor Mount Bathtub Filler Model Number: FTF01-TB (Brushed Nickel) FTF01-TC (Chrome) FTF01-TM (Matte Black) FTF01-TO (Oil Rubbed Bronze) Features: - Brass and Zinc Alloy Construction Single Hole Installation Drip Free 40 mm Ceramic Cartridge Hand shower flow rate 1.8 gpm at 80 psi Tub spout flow rate 3.
PAGE 2
Thank you for purchasing Luxier products. Please read the information below and keep this installation guide for future reference. If you require assistance, please contact our customer service department at 1-877-711-8828, Monday - Friday 9AM - 5PM Pacific Time or by email at support@luxierusa.com. Limited Lifetime Warranty (For USA Only) The manufacturer warrants this product to be leak and drip free during daily normal household use for as long as it is owned by the original purchaser of this product.
PAGE 3
Important Points • This installation guide is subject to change without notice, please contact us to request the most updated version of this installation guide. • This is a general installation guideline, actual installation may vary. Consult a professional if necessary. • Read and understand this instructions completely before installation. • Please follow all local building and plumbing codes. • Product drawings in this installation guide is for illustration purpose only.
PAGE 4
Installation The T-Connector needs to be fitted to both the hot and cold water pipes before installing the Tub Filler. The T-Connector should be about 3 7/8” below the surface of the finished floor and the floor opening should be 2.5” in diameter. See figure B. IMPORTANT: This product should be installed by professional installers. IMPORTANT: It is strongly recommended to dry fit all parts before final installation. IMPORTANT: Provide adequate clearance around the Tub Filler. Figure B.
PAGE 5
Installation 2 3 Top View Finished Wall Line Base Board 2.5” Hole Setscrew Handle Cartridge Stem Setscrew Cap Level 2. Remove the Cap and Setscrew from the Handle and loosen the Setscrew with the included Hex Wrench. Insert the Handle on the cartridge stem, tighten the Setscrew and install Cap to the Handle. (NOTE: The top Setscrew can be loosened to swivel the spout if needed. Tighten the Setscrew if the position of the spout was changed.) 3. Make sure the floor is level in both directions.
PAGE 6
Installation 6 7 6 2 1 3 1 Hex Fitting 4 5 6. Hold the Tub Filler Assembly in place and install the four Mounting Screws. Check alignment and level before fully tightening the screws. After tightening the screws slide the Escutcheon down to cover the flange. 7. Connect the Hand Shower Hose (5) to the Tub Filler with the hex nut end to the Tub Filler. (NOTE: Make sure the rubber washers (1) are installed on both end of the hose) Hand tighten the Hand Shower Wand (6) to the Hand Shower Hose (5).
PAGE 7
Operations Front View Diverter Knob To operate the tub filler simply move the handle to the ON position to turn on the water. Adjust the temperature by moving the handle from side to side to set the desired water temperature. Side View OFF ON HOT COLD To operate the hand shower wand, remove the hand shower from its holder and direct the jets into the tub. Pull the diverter knob on the faucet body. Push the diverter knob to direct the water back to the spout. Parts 01. Aerator Assembly 02.