Installation Guide

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and printed in U.S.A. 1/04 P/N 030-533 Rev. B
Wallplate Cutting
Some wallplates will need to be cut if removing side sections of
controls and not using a multigang wallplate. Position wallplate on
a soft cloth face down. Press firmly and score the groove on the
back of wallplate with a razor-sharp knife, using vertical side
groove to keep knife on straight course (see Figure H). Bend sec-
tion back and forth to break it off. Smooth edges by placing fine-
grained sandpaper on a flat surface and rub edge of the wallplate
over the sandpaper a few times. Hold wallplate steady as you rub
to keep a true edge.
Figure H. Cutting Wallplate
Figure F. Side Section Removal
Side section break-off points
Multigang wallplates, which eliminate the need to cut individual
wallplates, are available from Lutron in a variety of colors to sim-
plify and beautify your installation.
Note: Do not remove outer side sections of the two controls which
are on the ends of the gang.
4. Turn power OFF. Wire each control according to step 3 in
“Single Unit Installation” on page 1.
5. Install controls in wallbox(es). Use center mounting holes.
(With large controls, you can use offset mounting holes as
required for proper alignment). Allow 1/32" (0.8 mm) between con-
trols for ease in attaching wallplates.
6. Snap on multigang wallplate (or multiple single wallplates)
and adjust up or down for snug fit. Multigang wallplates (with
mounting frames and instructions) are available in a variety of col-
ors and sizes to simplify and beautify your installation. See Figure
E.
3. Remove only inner side sections. Using pliers, bend side sec-
tions as far as you can and then back to their original positions.
Repeat several times until side sections break off (See Figure F).
Limited Warranty
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture
within one year after purchase. For warranty service, return unit to place of purchase or mail
to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE
IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PUR-
CHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL
OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE
FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER
INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM
FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE,
SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE
PURCHASE PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages, or limitation on how long an implied warranty may last, so the above limitations
may not apply to you.
This product may be covered by one or more of the following U.S. patents: 4,803,380;
4,876,498; 4,954,768; DES 339,326 and corresponding foreign patents. U.S. and foreign
patents pending. The design of this dimmer is a registered trademark of Lutron Electronics
Co., Inc. and may be protected by one or more of the following U.S. trademark registrations:
1,617,349; 1,624,489; 1,624,490; 1,626,714; 1,638,913. Lutron, Nova and Tu-Wire are regis-
tered trademarks of Lutron Electronics Co., Inc.
© 2004 Lutron Electronics Co., Inc.
Technical Assistance
If you have questions concerning the installation or operation of
this product, call the Lutron Technical Support Center. Please
provide exact model number when calling.
[phone] (U.S.A., Canada, and the Caribbean)
Other countries call [phone]
Fax [phone] Internet: www.lutron.com