Cut Sheet

ManualsBrandsLutron ManualsBallastsElectronic Dimming Ballast, Fluorescent, T5, 1-Lamp, 21W, 120-277V

Table Of Contents

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

EcoSystem® Five Control Input Digital Dimming Ballasts

369454k 1 05.27.16

Digital electronic dimming ballasts maximize the

beneﬁts of a lighting management system.

EcoSystem

® Ballasts offer 100% to 10% dimming;

ideal for use where saving energy, increasing ﬂexibility,

and maximizing productivity are the goals of the

lighting design.

Features

• Continuous, ﬂicker-free dimming from 100% to 10%

• Integral sensor connection provides power for and

responds to one occupancy sensor, one photo

sensor, and one personal control input (infrared

receiver or wallstation)

• Communicates status and sensor inputs over the

EcoSystem

® digital link

• Programmed rapid start design ensures full rated

lamp life while dimming and cycling

• Lamps turn on to any dimmed level without ﬂashing to

full brightness

• Low harmonic distortion throughout the entire

dimming range

• Frequency of operation ensures that ballast does not

interfere with infrared devices

• End-of-lamp-life protection circuitry ensures safe

operation throughout entire lamp life

• Ultra-quiet operation

• Non-volatile memory restores all ballast settings after

power failure

• Ballasts maintain consistent light output for linear lamp

lengths (e.g., 4 ft [1.5 m], 3 ft [1 m], 2 ft [0.5 m] have

same relative output)

• Protected from miswires of any input power to control

lead, or from lamp leads to each other and/or ground

• 100% performance tested at factory

• Custom ballast factors available. Design tool

and speciﬁcations can be found at

www.lutron.com/ballasttool

• BAA-compliant (Buy American Act) model numbers

vailable. Add a "U" preﬁx to the model number.

EcoSystem

® case type G

EcoSystem

® case type J

EcoSystemR Multiple Control Input Ballasts

Summary of content (19 pages)

PAGE 1
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 1 05.27.16 EcoSystemR Multiple Control Input Ballasts Digital electronic dimming ballasts maximize the beneﬁts of a lighting management system. EcoSystem® Ballasts offer 100% to 10% dimming; ideal for use where saving energy, increasing ﬂexibility, and maximizing productivity are the goals of the lighting design.
PAGE 2
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 2 05.27.16 Speciﬁcations • • • • • • • • • • • • Regulatory Approvals UL® Listed (evaluated to the requirements of UL935) CSA certiﬁed (evaluated to the requirements of C22.2 No. 74) Select ballasts are NOM Listed (contact Lutron® for more information) S Mark Certiﬁed Class P thermally protected Some model numbers are not for sale in California. See tables on Pages 4-7 for details.
PAGE 3
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 3 05.27.16 How to Build a Model Number Example E C 5 T 8 3 2 G U N V 2 10 L F A B G H C I D E A – Type of Ballast EC = EcoSystem® Ballast B – Control Type 5 = 5 control inputs: EcoSystem® digital link, 3-wire phase control input, daylight sensor, occupancy sensor, and personal control (IR receiver or wallstation) C – Lamp Size (2 characters) T8 or T5 D – Lamp Wattage (2 characters) XX = Lamp wattage (e.g.
PAGE 4
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 4 05.27.16 EcoSystem® Ballasts with Integral Sensor Connection for Linear and U Bend T8 Lamps Lamp No. of Model Lamps F32T8 (48 in [1219 mm]) F17T8 (24 in [610 mm]) 1 Input Current (A) Input Power (W) Ballast Factor (BF) System System Ballast Relative Lumens Efﬁcacy Efﬁcacy Efﬁcacy (lm) (lm/W) Factor (RSE) 1 EC5 T832 J UNV 1 1 J 277 240 120 0.11 0.13 0.26 31.6 31.0 31.3 0.85 0.85 0.85 2550 2550 2550 81 82 81 2.69 2.74 2.
PAGE 5
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 5 05.27.16 EcoSystem® Ballasts for Linear and U Bend T8 Lamps: Reduced Wattage Lamp No.
PAGE 6
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 6 05.27.16 EcoSystem® Ballasts with Integral Sensor Connection for linear T5 Lamps Lamp No. of Model Lamps Input Current (A) Input Power (W) Ballast Factor (BF) System System Ballast Relative Lumens Efﬁcacy Efﬁcacy Efﬁcacy (lm) (lm/W) Factor (RSE) F35T5 (57.1 in [1450 mm]) 1 EC5 T535 J UNV 1 J 277 240 120 0.15 0.18 0.35 42.0 42.3 42.2 1.0 1.0 1.0 3650 3650 3650 87 87 87 2.38 2.38 2.38 0.83 0.83 0.83 F28T5 (45.
PAGE 7
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 7 05.27.16 EcoSystem® Ballasts with Integral Sensor Connection for Linear T5 HO Lamps Lamp No. of Model Lamps F54T5 (45.2 in [1148 mm]) F39T5 (33.4 in [848 mm]) F24T5 (21.6 in [549 mm]) 1 Case Input Size Voltage (V~) Input Current (A) Input Power (W) Ballast Factor (BF) System System Ballast Relative Lumens Efﬁcacy Efﬁcacy Efﬁcacy (lm) (lm/W) Factor (RSE) 1 EC5 T554 J UNV 1 1 J 277 240 120 0.21 0.24 0.48 56.5 58.0 57.9 1.0 1.
PAGE 8
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 8 05.27.16 EcoSystem® Ballasts with Integral Sensor Connection for T5 Twin Tube Lamps Lamp No. of Model Lamps FT55 (20.7 in [526 mm]) Case Input Size Voltage (V~) Input Current (A) Input Power (W) Ballast Factor (BF) System System Ballast Relative Lumens Efﬁcacy Efﬁcacy Efﬁcacy (lm) (lm/W) Factor (RSE) 1 EC5 T555 J UNV 1 J 277 240 120 0.20 0.23 0.46 55.4 55.2 55.2 0.9 0.9 0.9 4320 4320 4320 70 70 70 1.62 1.63 1.63 0.89 0.
PAGE 9
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 9 05.27.16 EcoSystem® Ballast Case Dimensions G Case A B C D E G Case Dimensions A = 9.5 in (241 mm) B = 8.9 in (226 mm) C = 7.1 in (180 mm) D = 1.0 in (25 mm) E = 2.38 in (60 mm) G case ballasts with leads ship with 36 in (914 mm) leads for lamp connections and 18 in (457 mm) leads for Line/Hot, Neutral, E1 and E2 connections J Case A B C D E J Case Dimensions A = 18.0 in (457 mm) B = 17.68 in (449 mm) F C = 6.
PAGE 10
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 10 05.27.
PAGE 11
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 11 05.27.16 EcoSystem® Ballast Wiring Diagrams — T5 Twin-Tube 369-454d 11 04.13.
PAGE 12
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 12 05.27.16 EcoSystem® Ballast Wiring: EcoSystem® Digital Link E1 E2 Class 2 Bus • The EcoSystem® digital link wiring (E1 and E2) connects the ballasts together to form a lighting control system. NEU DH HOT LINE EcoSystem® Digital Link Overview Ballast Terminals • Each EcoSystem® digital link supports up to 64 digital ballasts, 64 occupant sensors, 16 daylight sensors, and 64 wallstations or IR receivers.
PAGE 13
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 13 05.27.16 EcoSystem® Ballast Wiring: Class 2 Sensors Electrical Contractors and Engineers: • Always follow applicable national and local electrical code requirements when connecting circuits to EcoSystem® devices • All ﬁeld installed Class 2 wiring must be separated from line voltage wiring by at least 0.25 in (6.
PAGE 14
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 14 05.27.16 EcoSystem® Ballast Wiring: Daylight Sensor G Case Terminals Wiring to a Daylight Sensor NEU DH SH LINE E1 E2 Class 2 Bus • Sensor wiring summary: Ballast Terminal Terminal Color Red +20 V - Red Black Common Black White IR White +20V Yellow Common Yellow Daylight IR Occ Daylight • Make sure that the supply breaker to the Digital Ballast is OFF when wiring.
PAGE 15
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 15 05.27.16 EcoSystem® Ballast Wiring: Occupancy Sensor Wiring to a LutronR Occupancy Sensor (LOS-XX) G Case Terminals Terminal Color Red +20 V - Red Black Common Black Blue Occ Blue E1 E2 +20V Common • Make sure that the supply breaker to the Digital Ballast is OFF when wiring.
PAGE 16
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 16 05.27.16 EcoSystem® Ballast Wiring: IR Receiver and Wallstation Wiring to an IR Receiver and Wallstation G Case Terminals Red +20 V - Red Black Common Black White IR White E1 E2 +20V • Make sure that the supply breaker to the Digital Ballast is OFF when wiring. Common IR Occ Daylight • Connect the three conductors to the three Digital Ballast terminals as shown.
PAGE 17
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 17 05.27.16 EcoSystem® Ballast Wiring: Multiple Devices J Case Terminals Multiple Sensors with One Ballast • EcoSystem® ballasts accept wiring for one daylight sensor input, one occupant sensor input and one IR input (wallstation or IR receiver). +20V Common IR Occ Daylight Class 2 (22 AWG Solid) • EcoSystem® daylight sensors have IR outputs that allow the device to operate as a programming port.
PAGE 18
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 18 05.27.16 EcoSystem® Ballast Wiring: Line Voltage Dimmers NEU DH HOT E1 E2 Black Orange White • Make sure that the supply breaker to the Digital Ballast is OFF when wiring. Class 2 Bus Line/Hot LINE 3-Wire Control Wiring E1 E2 Class 2 Bus • Lutron® 3-wire dimmers only control the ballast they are wired to; EcoSystem® ballasts do not support grouping of 3-wire control input.
PAGE 19
EcoSystem® Five Control Input Digital Dimming Ballasts 369454k 19 05.27.16 ATTENTION ELECTRICIANS AND CONTRACTORS Ballast/Socket Leads Ballast Operating Temperature Lead lengths from ballast to socket must not exceed 7 ft (2 m) for linear lamps (T5, T5HO, T8). Lead lengths must not exceed 3 ft (1 m) for T5 twin tube lamps. Ballast case temperature must not exceed 167 °F (75 °C) at any point on ballast.