Installation Guide

ON
OFF
ON
OFF
ON
OFF
ON
OFF
x3
x2
Hold for 6 seconds
until light bar starts
blinking
quick-start guide
In-wall dimmer
Installation videos can be found here:
www.casetawireless.com/support
NOTE: You can mix and match dimmable LED and
CFLs, as well as halogen and incandescent light
bulbs, with Caséta Wireless dimmers.
Dimmable LED and CFL light bulbs vary in their
dimming performance. If you’re using these
bulbs and they flicker or turn off, please visit
www.casetawireless.com/lowend for information
on adjusting the dimmer for best bulb performance.
For a complete list of compatible dimmable
LEDs and CFLs, please visit
www.casetawireless.com/bulblist
LED—up to 150 W
CFL—up to 150 W
Contents supplied
Double your warranty
In-wall dimmer
(DVRF-6L)
Tools you’ll need
Works with energy efficient
dimmable light bulbs:
Flat-head screwdriver
Wire connectors (5)
Phillips-head screwdriver
Screws (2)
Installation for lights with one wall switch (single pole)
Installing your dimmer
To use your Caséta Wireless system
We’ve included instructions for when a single switch
is controlling the lights. For installation instructions
when two or more switches are controlling a light,
please visit www.casetawireless.com/3way
for complete installation instructions and how-to
videos.
WARNING: SHOCK HAZARD
May result in serious injury or death. Turn off
power at circuit breaker or fuse before installing.
1
Turn power off at circuit breaker!
1
Press and hold “off” button on dimmer
2
Press and hold “off” button on remote
4
Connect the dimmer
5
Mount the dimmer
6
Attach the wallplate
7
Turn power on at circuit breaker
2
Remove existing switch from wall
Remove the wallplate from switch.
Remove the switch and pull it away from the wall.
* If your switch has more than 3 wires attached, see
“Installing Caséta Wireless in a 3-way switch application”
video at www.casetawireless.com/3way
3
5
1
2
3
1
4
6
Ground
Ground
Ground
7
2
Disconnect all three wires* from the switch.
1 Connect the bare copper (or green) “ground” wire
from the wallbox to the green wire on the dimmer
using one of the large supplied wire connectors.
2 Connect either of the remaining wires from the
wallbox to the black wire on the dimmer using one of
the large supplied wire connectors.
3 Connect the remaining wire from the wallbox to
the red wire on the dimmer using one of the large
supplied wire connectors.
4 Cap the blue wire coming from the dimmer with the
small supplied wire connector. The blue wire is not
used for single pole installations.
Note: Wire colors depicted in this install guide may
not match what is in your walls.
Attach the adapter to the dimmer using the screws
provided and snap on the wallplate.
‘snap’
Use the screws provided.
Pairing the dimmer and Pico
remote control
Go to www.casetawireless.com/support for
additional troubleshooting suggestions.
Symptoms Probable cause and action
Light does not
turn on or in-wall
dimmer light bar
does not light up.
Light bulb(s) burned out.
Breaker is OFF or tripped.
Light not properly installed.
Wiring error.
FASS switch on the dimmer is
in the Off position.
Light does not
respond to Pico
remote control.
The dimmer failed to pair with
Pico remote control; see Pairing
the dimmer and Pico remote
control.
The dimmer is already at the
light level the Pico remote
control is sending.
The Pico remote control
is outside the 30 ft (9 m)
operating range.
The Pico remote control battery
is low.
The Pico remote control battery
is installed incorrectly.
Bulbs turn off
while being
dimmed.
Bulbs turn on
at high light
level but do not
turn on at a low
light level.
Bulbs flicker
or flash when
dimmed to a
low light level.
Verify bulbs are marked dimmable
and visit www.casetawireless.
com/lowend for information on
adjusting the dimmer for best bulb
performance.
Love Caséta Wireless products?
Have ideas for making them better? Tell us what
you think and we’ll extend your warranty by 1 year.
www.casetawireless.com/register
For advanced features, tips for using Caséta Wireless dimmers with LEDs and CFLs, the complete Caséta Wireless
product line, and more, please visit www.casetawireless.com/features
Changing the favorite light level
on the Pico remote control
(sold separately)
You can use the round “favorite”
button on the Pico remote control
to recall a favorite light level.
We’ve set it to 50%, but you can
change it to any level you like.
Favorite
Replacing light bulbs using FASS
Pull the FASS switch out on the in-wall dimmer to
remove power at the light socket.
CAUTION
Use only with permanently installed fixtures with
dimmable LED, dimmable CFL, halogen, or
incandescent,lamps. To avoid overheating and
possible damage to other equipment, do not use
to control receptacles, motor-driven appliances, or
transformer-supplied appliances.
Codes
Install in accordance with all national and local
electrical codes.
Grounding
When no “grounding means” exist in wallbox, the
National Electrical Code (NEC®) allows a control to
be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic
attachment screws or 2) the circuit is protected by a
ground fault circuit interrupter (GFCI). When installing
a control according to these methods, cap or remove
green wire before screwing control into wallbox.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Lutron, the Lutron logo, Diva, FASS, Caséta, Pico, and the design of the
Pico remote are trademarks or registered trademarks of Lutron Electronics
Co., Inc. in the US and/or other countries. Apple is a trademark of Apple
Inc., registered in the U.S. and other countries. App Store is a service
mark of Apple Inc. All other product names, logos, and brands are
property of their respective owners.
© 2022 Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
1
2
1
2
Hold for 6 seconds until
light bar blinks twice
on in-wall dimmer. New
favorite level is now saved.
3
Set desired light level on dimmer
4
Press and hold favorite” button on remote
Important note:
Troubleshooting
Hold for 6 seconds until
lights flash 3 times.
Diva Smart Dimmer
DVRF-6L
120 V~ 50/60 Hz
Important notes:
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Pico remote control (sold separately)
On
Off
Adjust slider to dim / brighten
the light level
• Will not turn lights off
FASS
Front Accessible
Service Switch
In-wall dimmer
On
Off
Darker
Favorite
Brighter
With a smartphone or tablet (Smart Hub required, sold separately)
3
Use the Lutron app to complete ALL remaining steps
The Caséta Wireless Diva Smart Dimmer can be controlled from
a smartphone when used with the Lutron Smart Hub (Smart Bridge)
and the Lutron app.
If you are using the dimmer and remote control with the Lutron
Smart Hub follow the instructions below.
Lutron Smart Hub
Lutron app
Without a smartphone or tablet (Smart hub not required)
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
P/N 0302045 REV A
Incandescent—up to 600 W
Control
three ways
Add devices
Pico remotes
• Dimmers
• Shades
Schedule
your lights
Connect
while away
Important note:
Multi-gang installations may reduce the dimmer’s
maximum wattage rating. See the chart below for
maximum wattage information.
* For maximum wattage information when
mixing light bulb types see
www.casetawireless.com/ganging
Maximum* wattage derating chart
(120 V~ 50/60 Hz)
Load Type
Single
gang
Double
gang
Triple
gang
LED & CFL 150 W 150 W 150 W
or
*
Incandescent &
Halogen
600 W 500 W 400 W
3
Halogen—up to 600 W
Set the light level by
adjusting the slider
up and down
Double Gang Triple Gang
3
Ganging and Derating
4
Note: If you are using the dimmer and remote control with
another manufacturer’s bridge, please refer to that manufacturer’s
instructions for set-up.
1 Press and hold “off” button on dimmer
2
Press and hold “off” button on remote
The Lutron app will walk you through
setting up your devices.
Download the Lutron app
Launch the Lutron app
Search for “Lutron Caséta”
Repeat steps to pair other Pico
remote controls.
Using your controls

Summary of content (3 pages)