Installation Guide

x3
Hold for 6 seconds
until LED starts
blinking
Supported Loads (120 V~)
To use your Caséta by Lutron system
1
Press and hold “off” button on the switch
2
Press and hold “off” button on remote
Pairing the switch and
Pico remote control
Go to www.casetawireless.com/support for
additional troubleshooting suggestions.
Symptoms Probable cause and action
Light does not
turn on or switch
LED does not
light up.
• Red and black wires on the
switch are reversed.
(See steps 4.2 and 4.3 on
the previous page)
• Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASS on the switch is in the
Off position.
Light does not
respond to Pico
remote control.
• The switch failed to pair with
Pico remote control; see Pairing
the switch and Pico remote
control.
• The switch is already at the light
level the Pico remote control is
sending.
• The Pico remote control is
outside the 30 ft (9 m) operating
range.
• The Pico remote control battery
is low.
• The Pico remote control battery
is installed incorrectly.
Load is Off and
the status LED is
blinking 4 times,
pause, and
repeats.
• The switch is in an Over
Temperature Protection (OTP)
mode.
• See Step 3 Ganging and
Derating. Ensure the switch is
not overloaded.
• Reset the switch by using the
FASS, Front Accessible Service
Switch; See Using your Controls
section. Pull out the FASS and
push it back in.
For advanced features, tips for using Caséta products with LEDs, the complete Caséta product line, and more, please
visit www.casetawireless.com/features
Replacing light bulbs using FASS
Pull the FASS out on the switch to remove power at
the light socket.
Lutron, the Lutron logo, Caséta, Claro, FASS, and Pico are trademarks
or registered trademarks of Lutron Electronics Co., Inc. in the US and/
or other countries. Apple is a trademark of Apple Inc., registered in the
U.S. and other countries. App Store is a service mark of Apple Inc. All
other product names, logos, and brands are property of their respective
owners.
© 2022 Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Troubleshooting
Hold for 6 seconds
until lights flash 3 times.
Important notes:
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Repeat steps to pair other Pico remote controls.
Pico remote control (sold separately)
On
Off
FASS
Front Accessible
Service Switch
Switch
With a smartphone or tablet (Smart Hub required, sold separately)
The Claro Smart Switch can be controlled from a smartphone when
used with the Lutron Smart Hub (formerly Smart Bridge). All devices
must be within 30 ft (9 m) from the Lutron Smart Hub.
If you are using the switch and remote control with the Lutron
Smart Hub follow the instructions below.
Lutron Smart Hub
Lutron app
Without a smartphone or tablet
(Smart Hub not required)
LED—up to 5 A
Incandescent / Halogen—up to 600 W
MLV—up to 600 VA
ELV—up to 600 W
Fluorescent—up to 5 A
General Purpose Fan—up to 3 A
Using your controls
On
Off
DVRF-5NS
1 Press and hold “off” button on dimmer
2
Press and hold “off” button on remote
The Lutron app will walk you through
setting up your devices.
Download the Lutron app
Launch the Lutron app
Search for “Lutron Caséta”
3
Press and hold “off” button on remote
Use the Lutron app to complete ALL remaining steps
Note: If you are using the switch and remote control with
another manufacturer’s bridge, please refer to that manufacturer’s
instructions for set-up.
Control
three ways
Add devices
• Pico remote controls
• Dimmers
• Shades
Schedule
your lights
Connect
while away