User's Manual

ManualsBrandsLutron Electronics ManualsElectronicsCar Visor Control

Preliminary RadioRA Car Visor Control Instructions 09/19/01

Page 1 of 10

Adding a Car Visor Control

The Car Visor Control is a special type of Master Control. The System can have a maximum of

12 Master Controls. For every 1 Master Control NOT used, a Car Visor Control may be used in

its place.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures: Reorient or relocate the receiving antenna. Increase the separation between the

equipment and receiver. Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by Lutron Electronics could void the

user’s authority to operate this equipment.

Step 1 Begin Control Activation

Press and hold the ACTIVATE CONTROLS

button on any Repeater until the green

ACTIVATE CONTROLS LED turns ON

(approximately 3 seconds).

Step 2 Activate Controls

To add a Car Visor Control

Press any button.

• All LEDs will flash, then

• Top and bottom row will flash alternately

Middle row of LEDs will turn ON when the

Master Control has been activated.

Car Visor Receiver

Step 3 Complete Car Visor

Control Activation

Press and hold the ACTIVATE CONTROLS

button on any Repeater until the green

ACTIVATE CONTROLS LED turns OFF

(approximately 3 seconds).

The green ACTIVATE CONTROLS LED on

ALL Repeaters will turn OFF. The MAIN or

AUXILIARY LED will remain on.

Summary of content (10 pages)

PAGE 1
Preliminary RadioRA Car Visor Control Instructions 09/19/01 Adding a Car Visor Control The Car Visor Control is a special type of Master Control. The System can have a maximum of 12 Master Controls. For every 1 Master Control NOT used, a Car Visor Control may be used in its place. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 2
Preliminary RadioRA Car Visor Instructions 09/19/01 Programming Preparations Assigning the Lights Column of Buttons as ROOMS or SCENES on your Car Visor Control The right most column of buttons on a Car Visor Control can be programmed to be either ROOM or SCENE buttons.
PAGE 3
Preliminary RadioRA Car Visor Instructions 09/19/01 Step 3 Step 5 Label columns Changing the closure type for the Input buttons (continued) If a CCI is set as Momentary (default setting), its LED will be OFF. If a CCI is set as Maintained, its LEDs will be ON. Apply the supplied ROOMS or SCENES labels to the space provided over the right most button column. To change the setting to Maintained, press and hold the CCI button until the LED turns ON.
PAGE 4
Preliminary RadioRA Car Visor Instructions 09/19/01 Assigning Dimmers, Switches, or GRAFIK Eye Control Units to Car Visor Control Buttons Step 1 Begin assigning Step 2 Select a Button Dimmers, Switches, or GRAFIK Eye® Control Units to buttons Press the button that you want to program. Its LED will begin to flash. Simultaneously press and hold the 2nd and 4th buttons in the right most column until the upper right LED begins to flash (approximately 3 seconds).
PAGE 5
Preliminary RadioRA Car Visor Instructions Step 3 Assign a Dimmer, Switch, or GRAFIK Eye Control Unit to the button. Notes: • Multiple Dimmers, Switches, or GRAFIK Eye ® Control Units can be assigned to a button. 09/19/01 If you assign the wrong Dimmer, Switch, or GRAFIK Eye ® Control Unit to the Car Visor Control button, turn the Dimmer, Switch, or GRAFIK Eye ® Control Unit OFF to unassign it. Note: GRAFIK Eye ® Control Units will automatically turn on to scene 1 once assigned.
PAGE 6
Preliminary RadioRA Car Visor Instructions 09/19/01 Setting Light Levels/Grafik Eye Scene Selection for ROOM Buttons Setting Light Levels/ Levels/Grafik Eye Scene for SCENE Buttons This section is not complete yet… For this option, refer to the “Setting Light Levels” section of the RadioRA Setup Guide - Use Pages 1-11 and 1-12 for ROOM Buttons - Use Pages 1-15 and 1-16 for SCENE Buttons Page 6 of 10
PAGE 7
Preliminary RadioRA Car Visor Instructions 09/19/01 Programming a Car Visor Transmitter The Car Visor Control can learn a maximum of 7 Car Visor Transmitters. Step 1 Begin Learning a Step 2 Select the Receiver Transmitter to the Receiver Button to be learned to the Transmitter Button Press and hold the LEARN button (approximately 3 seconds) on the Car Visor Receiver until the LED turns on.
PAGE 8
Preliminary RadioRA Car Visor Instructions Step 3 Learn the Transmitter Button to the Receiver 09/19/01 The receiver button turns off indicating that the transmitter button has been learned to the receiver button. Press and hold the Transmitter button (approximately 3 seconds) until the LED of the selected Receiver button flashes for 3 seconds. If the transmitter is learned to the ALL ON button, the LEDs in the right most column will rapidly flash upward for 3 seconds.
PAGE 9
Preliminary RadioRA Car Visor Instructions 09/19/01 Step 6 Complete Transmitter Activation Press and hold the LEARN button on the Car Visor Receiver (approximately 3 seconds) until the LED turns off.
PAGE 10
Preliminary RadioRA Car Visor Instructions 09/19/01 Returning the Car Visor Control to Default Factory Settings Step 1 Begin returning to Step 2 Complete returning to default factory settings default factory settings st rd th Press and hold the 1 3 and 5 buttons in the right most column until the corresponding LEDs begin to flash (approximately 3 seconds). st rd th While the 1 , 3 , and 5 LEDs are flashing, nd th press and hold the 2 and 4 buttons in the right most column until all LEDs flash.