Datasheet

DS105 LUXEON Z Colors Product Datasheet 20150130 ©2015 Lumileds Holding B.V. All rights reserved. 5
Optical Characteristics
LUXEON Z Color at 500mA, Test Temperature
Table 3.
Color Part Number
Dominant Wavelength
[1]
, l
D
or Peak Wavelength
[2]
, l
P
(nm)
Typical
Spectral
Half-width
[3]
(nm)
Dl
1/2
Typical Temp
Coecient of
Dominant or
Peak Wavelength
(nm/°C)
Dl
D
/ DT
J
Typical
Total
Included
Angle
[4]
(degrees)
u
90V
Typical
Viewing
Angle
[5]
(degrees)
2u ½
Min Typ Max
Green
[6]
LXZ1-PM01 520.0 530.0 540.0 30 0.04 140 125
Cyan
[6]
LXZ1-PE01 490.0 505.0 510.0 30 0.03 140 125
Blue
[6]
LXZ1-PB01 460.0 470.0 480.0 20 0.03 140 125
Royal Blue
[2] [6]
LXZ1-PR01 440.0 447.5 460.0 20 0.03 140 125
Red
[7]
LXZ1-PD01 620.0 627.0 645.0 20 0.06 150 145
Red
[7] [8] [9]
LXZ1-PD02 624.0 626.0 634.0 20 0.06 150 145
Deep Red
[7]
LXZ1-PA01 650.0 655.0 670.0 20 0.06 150 145
Red-Orange
[7]
LXZ1-PH01 610.0 617.0 620.0 20 0.06 150 145
Red-Orange
[7] [8] [9]
LXZ1-PH02 614.0 619.0 624.0 20 0.06 150 145
Amber
[7]
LXZ1-PL01 585.0 590.0 595.0 20 0.10 150 145
Amber
[7] [8] [9]
LXZ1-PL03 594.0 597.0 604.0 20 0.10 150 145
PC Amber
[6] [8]
LXZ1-PL02 588.0 590.0 592.0 80 0.01 140 125
Lime
[8]
LXZ1-PX01 566.0 567.5 569.0 100 0.01 140 125
Notes for Table 3:
1. Dominant wavelength is derived from the CIE 1931 Chromaticity diagram and represents the perceived color.
Lumileds maintains a tolerance of ±0.5 nm for dominant wavelength measurements.
2. Royal Blue and Deep Red LEDs are binned by radiometric power and peak wavelength rather than photometric lumens.
Lumileds maintains a tolerance of ±2nm for peak wavelength measurements.
3. Spectral width at 1/2 of the peak intensity.
4. Total angle at which 90% of total luminous ux is captured.
5. Viewing angle is the o axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value.
6. Green, cyan, blue, royal blue, PC Amber, Lime and white products are built with Indium Gallium Nitride (InGaN).
7. All red, deep red, red-orange, and amber are built with Aluminum Indium Gallium Phosphide (AlInGaP).
8. LUXEON Z Lime, PC Amber and certain Red, Red-Orange and Amber emitters are tested and binned at T
j
= 85°C. All other LUXEON Z Color emitters are tested and binned at T
j
= 25°C.
9. Wavelength ranges for hot tested Red, Red-Orange and Amber have been dened to align with typical changes in spectral output at increased temperature, which are inherent to AlInGaP LEDs.
At T
j
= 25°C these hot-tested parts will have the same typical spectral outputs as their cold-tested counterparts.