Datasheet

DS103 LUXEON M Product Datasheet 20150205 ©2015 Lumileds Holding B.V. All rights reserved. 8
Electrical Characteristics for LUXEON M at Test Current
[1]
,
Junction Temperature = 85°C for all CCTs and Royal Blue
Table 9.
Part Number
Forward Voltage V
f
[1, 2]
(V)
I
f
= 700mA, 1400mA and 2800mA
Typical Temperature Coecient
of Forward Voltage
[3]
(mV/°C)
DV
F
/ DT
J
Typical Thermal Resistance
Junction to Thermal Pad
(°C/W)
Ru
J-C
Minimum Typical Maximum
LXRx-Sxxx 10.5 11.2 11.7 -5.5 1.25
LXRx-Rxxx 5.25 5.6 6 -2.75 1.25
LXRx-Qxxx 2.63 2.8 3 -1.38 1.25
Notes for Table 9:
1. Test current is 700mA for LXRx-Sxxx, 1400mA for LXRx-Rxxx and 2800mA for LXRx-Qxxx products.
2. Lumileds maintains a tolerance of ± 0.06V on forward voltage measurements.
3. Measured between T
J
= 25°C and T
J
= 135°C.
Absolute Maximum Ratings
Table 10.
Parameter Maximum Performance
DC Forward Current (mA)
[1], [2]
1200mA for LXR7-Sxxx, LXR8-Sxxx, LXR9-Sxxx; 2400mA for LXR7-Rxxx, LXR8-Rxxx,
LXR9-Rxxx; 4800mA for LXR7-Qxxx, LXR8-Qxxx, LXR9-Qxxx; 1050mA for LXR0-Sxxx;
2100mA for LXR0-Rxxx; 4200mA for LXR0-Qxxx
Peak Pulsed Forward Current
[1], [3]
1375mA for LXR7-Sxxx, LXR8-Sxxx, LXR9-Sxxx; 2750mA for LXR7-Rxxx, LXR8-Rxxx,
LXR9-Rxxx; 5500mA for LXR7-Qxxx, LXR8-Qxxx, LXR9-Qxxx; 1200mA for LXR0-Sxxx;
2400mA for LXR0-Rxxx; 4800mA for LXR0-Qxxx
ESD Sensitivity
≤ 8000V Human Body Model (HBM) Class 3B JS-001-2012
< 400V Machine Model (MM) Class B JESD22-A115-B
LED Junction Temperature
[1]
135°C
Operating Case Temperature at Current
-40°C - 120°C @ 700mA for LXRx-Sxxx
-40°C - 120°C @1400mA for LXRx-Rxxx
-40°C - 120°C @ 2800mA for LXRx-Qxxx
Storage Temperature -40°C - 120°C
Lead Soldering Temperature JEDEC 020c 260°C
Allowable Reow Cycles 3
Autoclave Conditions
121°C at 2 ATM
100% Relative Humidity for 96 Hours Maximum
Reverse Voltage (V
r
) LUXEON M LEDs are not designed to be driven in reverse bias
Notes for Table 10:
1. Proper current derating must be observed to maintain junction temperature below the maximum.
2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple”, with frequencies ≥ 100Hz and amplitude ≤ 1200mA for LXR0-Sxxx,
≤ 2400mA for LXR0-Rxxx and ≤ 4800mA LXR0-Qxxx products are acceptable, assuming the average current throughout each cycle does not exceed 1050mA for LXR0-Sxxx, 2100mA for
LXR0-Rxxx and 4200mA for LXR0-Qxxx.
3. Pulsed operation with a peak drive current of 1200mA for LXR0-Sxxx, 2400mA for LXR0-Sxxx and 4800mA for LXR0-Qxxx are acceptable if the pulse on time is ≤ 5ms per cycle and the duty
cycle is ≤ 50%.
4. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple”, with frequencies ≥ 100Hz and amplitude ≤ 1375mA for LXR7-
Sxxx. LXR8-Sxxx, LXR9-Sxxx, ≤ 2750mA for LXR7-Sxxx. LXR8-Sxxx, LXR9-Sxxx and ≤ 5500mA for LXR7-Sxxx. LXR8-Sxxx, LXR9-Sxxx products are acceptable, assuming the average current
throughout each cycle does not exceed 1200mA forLXR7-Sxxx. LXR8-Sxxx, LXR9-Sxxx, 2400mA for LXR7-Sxxx. LXR8-Sxxx, LXR9-Sxxx and 4800mA for LXR7-Sxxx. LXR8-Sxxx, LXR9-Sxxx.
5. Pulsed operation with a peak drive current of 1370mA for LXR7-Sxxx. LXR8-Sxxx, LXR9-Sxxx, 2750mA for LXR7-Sxxx. LXR8-Sxxx, LXR9-Sxxx and 5500mA for LXR7-Sxxx. LXR8-Sxxx,
LXR9-Sxxx are acceptable if the pulse on time is ≤ 5ms per cycle and the duty cycle is ≤ 50%.
JEDEC Moisture Sensitivity
Table 11.
Level Floor Life
Soak Requirements
Standard
Time Conditions Time Conditions
1 Unlimited
[ 30°C / 85% RH
168 Hrs. + 5 / -0 Hrs. 85°C / 85% RH