Datasheet

ManualsBrandsLUMILEDS ManualsHighPower-LEDsHighPower LED Warm white 95 lm 120 ° 2.76 V 1000 mA

GENERAL ILLUMINATION

RoHS

COMPLIANT

FEATURES AND BENEFITS PRIMARY APPLICATIONS

3- & 5-step MacAdam ellipse: Freedom from Binning for superior quality of light High Bay & Low Bay

Ability to deliver high Lm/$ for Indoor applications Outdoor

Low typical V

~ 2.8V

Small optical source size

Full range of CCTS in 80CRI minimum

LM-80 test report available

LUXEON Rebel PLUS is designed with the highest possible ecacy and

light output from an industry standard 4530 package witha 2.5mm

dome.

With hot testing and color binning, every LUXEON Rebel PLUS is tested

and specied at real world operating conditions — 85°C. Our exceptional

color control enables design simplicity for luminaire manufacturers and

ensures that they can be condent in color consistency from LED to LED.

The superior quality of light, light output, and real world ecacy enable

leading performance and ecient solution development in a wide variety

of outdoor and industry lighting segments.

LUXEON Rebel PLUS

The original high-power LED

Summary of content (17 pages)

PAGE 1
General Illumination LUXEON Rebel PLUS The original high-power LED LUXEON Rebel PLUS is designed with the highest possible efficacy and light output from an industry standard 4530 package witha 2.5mm2 dome. With hot testing and color binning, every LUXEON Rebel PLUS is tested and specified at real world operating conditions — 85°C. Our exceptional color control enables design simplicity for luminaire manufacturers and ensures that they can be confident in color consistency from LED to LED.
PAGE 2
Table of Contents General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Lumen Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
General Information Part Number Nomenclature LUXEON Rebel PLUS emitters are tested and binned “hot” under conditions comparable to those found in “realworld” lighting products. The test conditions for LUXEON Rebel PLUS are 350mA D.C. with junction temperature at 85°C.
PAGE 4
Product Selection & Optical Characteristics Product Selection Guide for LUXEON Rebel PLUS Emitters Junction Temperature = 85°C Table 1. Part Number Nominal ANSI CCT LX18-P127-Y Performance @ 350mA Test Current Typ. Luminous Flux (lm) Typ. Forward Voltage (V) Typ. Efficacy (lm/W) CRI Min Min Luminous Flux (lm) Test Condition °C 350mA 700mA 350mA 700mA 350mA 700mA 2700K 80 80 85 85 156 2.76 2.85 88 78 LX18-P130-Y 3000K 80 85 85 95 166 2.76 2.
PAGE 5
Electrical Characteristics Electrical Characteristics at 350mA for LUXEON Rebel PLUS, Junction Temperature = 85°C Table 3. Nominal ANSI CCT 2700K Min Max Typical Temperature Coefficient of Forward Voltage [2] (mV/°C) DVF / DTJ 2.5 3.00 -1.0 to -3.0 Forward Voltage Vf [1] (V) Typical Thermal Resistance Junction to Thermal Pad (°C/W) RuJ-C 9 3000K 2.5 3.00 -1.0 to -3.0 9 3500K 2.5 3.00 -1.0 to -3.0 9 4000K 2.5 3.00 -1.0 to -3.0 9 5000K 2.5 3.00 -1.0 to -3.
PAGE 6
Reflow Soldering Characteristics Figure 1. Temperature Profile for Table 6. Table 6.
PAGE 7
Mechanical Dimensions Figure 2. Package outline drawing. Notes for Figure 2: 1. Do not handle the device by the lens, as the lens or the interior of the device can be damaged by excessive force to the lens. 2. Drawings not to scale. All dimensions are in millimeters. 3. The thermal pad is electrically isolated from the anode and cathode contact pads. DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.
PAGE 8
Pad Configuration 3 1 3 2 TOP 2 1 BOTTOM PAD FUNCTION 1 CATHODE 2 ANODE 3 THERMAL Figure 3. Pad configuration. Note for Figure 3: 1. The Thermal Pad is electrically isolated from the Anode and Cathode contact pads. Solder Pad Design Figure 4. Solder pad layout. Notes for Figure 4: 1. The photograph shows the recommended LUXEON Rebel PLUS layout on Printed Circuit Board (PCB). This design easily achieves a thermal resistance of 7K/W. 2.
PAGE 9
Typical Light Output Characteristics over Temperature All LUXEON Rebel PLUS Emitters at Test Current, 350mA 1.15 1.1 Normalized Flux, [-] 1.05 1 0.95 0.9 0.85 0.8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature, [ o C] Figure 5. Relative light output vs. junction temperature. DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.
PAGE 10
Typical Forward Current Characteristics All LUXEON Rebel PLUS Emitters, Junction Temperature = 85°C 700 600 Forward Current, [mA] 500 400 300 200 100 2.66 2.68 2.7 2.72 2.74 2.76 2.78 2.8 2.82 2.84 2.86 Forward Voltage, [V] Figure 6. Forward current vs. forward voltage. Typical Relative Luminous Flux vs. Forward Current for All LUXEON Rebel PLUS Emitters, Junction Temperature = 85°C 1.8 1.6 Normalized Flux, [-] 1.4 1.2 1 0.8 0.6 0.4 0.
PAGE 11
Typical Radiation Patterns Relative Spectral Distribution for LUXEON Rebel PLUS Emitters 1 2700K 3000K 3500K 4000K 5000K 0.9 0.8 Relative Power, [-] 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 350 400 450 500 550 600 650 700 750 800 850 Wavelength, [nm] Figure 8. Cartesian plot of typical luminous intensity. Typical Polar Radiation Pattern 100 90 80 70 60 50 40 30 20 10 100 90 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 Normalized Flux [%] Figure 9. Typical polar radiation pattern.
PAGE 14
Product Binning and Labeling Purpose of Product Binning In the manufacturing of semiconductor products, there is a variation of performance around the average values given in the technical data sheets. For this reason, Lumileds bins the LED components for luminous flux and forward voltage (Vf ). Color is offered in a single 3-step or 5-step MacAdam ellipse color space centered on the ANSI CCT color bins. For additional information please review the MacAdam ellipse technical definition section.
PAGE 15
Luminous Flux and Forward Voltage Bins Table 7 lists the standard photometric luminous flux bins for LUXEON Rebel PLUS emitters (tested and binned at 350mA D.C., Junction Temperature = 85°C. Minimum luminous flux performance within published operating conditions. Lumileds maintains a tolerance of ±6.5% on luminous flux measurements. Although several bins are outlined, product availability in a particular bin varies by production run and by product performance. Not all bins are available in all CCT’s.
PAGE 16
LUXEON Rebel PLUS 3-step and 5-step MacAdam Ellipse Color Definition Tested at 350mA D.C. & Junction Temperature = 85°C Color Space Definition for Above and Below Blackbody Parameter Definition of MacAdam Ellipse Table 9. LUXEON Rebel PLUS Product Characteristics for 3-step MacAdam Ellipse Part Number Nominal ANSI CCT Color Space Center Point (cx, cy) Major Axis, a Minor Axis, b Ellipse Rotation Angle (degrees) LX18-P127-3 2700K Single 3-step MacAdam ellipse (0.4578, 0.4101) 0.00810 0.
PAGE 17
About Lumileds Lumileds is the light engine leader, delivering innovation, quality, and reliability. For 100 years, Lumileds commitment to innovation has helped customers pioneer breakthrough products in the automotive, consumer and illumination markets. Lumileds is shaping the future of light with our LEDs and automotive lamps, and helping our customers illuminate how people see the world around them. To learn more about our portfolio of light engines visit www.lumileds.com. ©2015 Lumileds Holding B.V.