Specification Sheet

Important Notes
Please read before installing
1. Turn off power at circuit breaker or fuse before wiring.
2. Only one dimmer can be used per 3-way circuit.
3. It is normal for the dimmer to feel warm to the touch during operation.
4. FOR SUPPLY CONNECTOR, USE WIRES RATED FOR AT LEAST 75ºC and USE COPPER
WIRE ONLY.
Operation
The 0-10 volt low-voltage lighting control provides dimming control for 0-10 volt compatible LED
drivers, uorescent ballast and HID ballast. Minimum light level (low-end) shall be adjusted to
optimize performance.
0-10V Preset Dimmer
For use with: 0-10V Lighting Control Devices
Warranty Information
If within two(2) year from the date of purchase, this product fails due to a defect in material or
workmanship, we will repair or replace it, at its sole option, free of chare. This warranty does not
apply to: (a) damae to units caused by accident, droppine or abuse in handline, acts of God or
any neelient use; (b) units which have been subject to unauthorized repair, opened, taken apart
or otherwise modied; (c) unit not used in accordance with instructions; (d) damaes exceedine
the cost of the products. This warranty service is available by returnine the products with proof
of purchase date and a description of the problem to dealer from whom the unit was purchase.
Multi-gang Installation Sheet (Without Power Pack):
Cat. No. Single-Gang RatingDevice Rating Double-Gang Rating
120V AC, 50-60Hz, 6A
277V AC, 50-60Hz, 3A
CFL/LED/Electronic
self-ballasted
120V AC, 50-60Hz, 6A
277V AC, 50-60Hz, 3A
CFL/LED/Electronic
self-ballasted
120V AC, 50-60Hz, 6A
277V AC, 50-60Hz, 3A
CFL/LED/Electronic
self-ballasted
120V AC, 50-60Hz, 6A
277V AC, 50-60Hz, 3A
CFL/LED/Electronic
self-ballasted
DMD-LED3-105
DMD-LED3-106
Triple-Gang Rating
Installation
1. Turning power OFF.
- Turn power OFF.
2. Wiring the Dimmer.
3. Mounting dimmer to wallbox.
Push wires carefully into the wallbox, Install wallplate.
Side
Turn power ON.
4. Turning power ON.
A. Dimming Only Wiring
120–277 V~ 50 / 60 Hz
B2. 3-Way Wiring
Connect the 0-10 V Control
Wire the controls according to the appropriate wiring diagram
shown below and on the ballast/driver.
B1. Single Pole Wiring
CAUTION - To Reduce The Risk of Overheating and Possible Damage to Other Equipment, Do
Not Install to Control a Receptacle, a Motor-Operated Appliance or a Fluorescent Lighting Fixture
or a Transformer Supplied Appliance.
ATTENTION - Pour réduire le risque de surchauffe et les possibles dommages à d'autres
équipements, ne pas installer pour contrôler un réceptacle, un appareil à moteur ou un luminaire
uorescent ou un appareil fourni par transformateur.
Power wiring not shown—see lighting device for wiring
0-10 V Ballast/Driver
0-10 V Ballast/Driver
Gray (-)
Purple (+)
BlackRed
Red
C. Dimming With ON/OFF Control
B. Dimming With ON/OFF Control Without Power Pack
Wiring Diagram Using Power Pack
Power
Pack
0-10 V Ballast/Driver
0-10 V Ballast/Driver
Red
Red
Red
Red
Gray (-)
Red
Purple (+)
White
Black
Blue
Black
Black
Neutral
Hot/Live
120-277 V~ 50/60Hz
Neutral
Hot
Neutral
Hot
0-10 V Ballast/Driver
0-10 V Ballast/Driver
Neutral
Hot
Neutral
Hot
Red
Red
Green(Ground)Green(Ground)
Gray (-)
Purple (+)
Black
Neutral
120 -
277 V~
3-Way
Switch
Hot
Red
Green(Ground)
Gray (-)
Purple (+)
0-10 V Ballast/Driver
0-10 V Ballast/Driver
Black
Neutral
Neutral
120 - 277 V~
Hot
Hot
Neutral
Hot
LIGHTS DO NOT OPERATE AT FULL BRIGHTNESS:
Push slide up. Turn high-end knob clockwise with a screwdriver to achieve maximum light
intensite.
LIGHTS DO NOT DIM LOW ENEOUGH:
Push slide down. Turn the low-end knob counter-clockwise to achieve minimum light intensity.
Dimming Range Adjustment
1. Push dimmer on and move slider down to the bottom.
2. Turn knob down until lowest light level is achieved and light output is stable for all bulbs.
3. Turn dimmer off, then back on to verify bulbs.
4. Turn knob up lightly and do step 3 again if all bulbs do not turn on.
IMPORTANT: To avoid lights turn off or icker at low end: Push slide down. Turn the
low-end knob clockwise until the lights remain on without ickering.
Turn down:
Less bright.
Slider: Controls light level.
Up increases light level, down decreases light level.
Switch: Turns lights ON and OFF
Turn up:
Brighter.
Minimum
Light Level
(low-end)
Knob
Maximum
Light Level
(High End)
Knob
+
-
Sensitivity Knob
Note: Wire locations will vary. Reference wires by color not location.
Dimming With ON/OFF Control Wallbox Wiring
Dimming Only Wallbox Wiring
Note: Wire locations will vary.
Reference wires by color not location