Owner manual
Manuals
Brands
LumaSense Technologies Manuals
Software
Pearl Control
11
12
13
14
15
16
17
18
19
20
Table Of Contents
1 Introduction
1.1 Information About the User Manual
1.2 Conventions
1.3 System Requirements
1.4 Camera and Core Configurations
1.4.1 Standard Camera and Core Configurations
1.5 About the Pearl Control Software Interface
1.5.1 Title Bar
1.5.2 Menu Bar
1.5.3 Action Bar
1.5.4 Workspace Area
1.5.5 Information Bar
1.6 Getting Started
1.6.1 Installing the Software
1.6.2 Starting the Software
1.6.3 Configuring Settings
To configure the program settings:
To configure the COM settings:
1.6.4 Connect a Camera or Core
2 Configuring Video Settings
2.1 Display Settings
2.1.1 Display Adjustment Mode
2.1.3 Brightness
To edit the brightness:
2.1.4 Contrast
To edit the contrast:
2.2 Color Map
To set the default color map:
2.3 Polarity
To change the default polarity:
2.4 Frame Average
To change the default frame average:
2.5 Flipping
To use the flipping feature:
2.6 Regional AGC
To turn on/off Regional AGC:
2.6.1 Graphical Overlay
To turn the graphical overlay on:
2.7 Auto-Cal
To turn on automatic calibration:
To turn off automatic calibration:
2.8 Display Logo and Temperature
3 Capturing Images and Data
3.1 Data Selection
3.2 Capturing Images
To capture an image:
To change the color map when capturing an image:
3.3 Copying Images
To copy an image:
3.4 Saving Data
To save data to the default location:
To save data to a new location:
4 Using Calibrate Tab Features
4.1 Accessing the Calibrate Tab
To access the Calibrate Tab:
4.1.1 Reset Camera
To reset the camera:
4.2 Adjusting Signal Settings
4.2.1 Integration Time
To adjust the integration time:
4.2.2 Gain
To adjust the gain value:
4.2.3 Correct Image
To correct the image:
4.2.4 Baudrate
To adjust the baudrate:
4.3 Using the Gain Map
4.3.1 Reset Map
To reset the map:
4.3.2 Correct Image
To correct the image:
4.3.3 Set Low Point
To set the low point:
4.3.4 Set High Point
To set the high point:
4.3.5 Save Map
To save the gain map to the camera permanently:
4.3.6 Performing a “Two-Point” Correction
To perform a “two-point” correction:
4.4 Replacing Pixels
4.4.1 Selecting an Image for Pixel Replacement
Image Source
To add the image from the Capture tab to the Pixel Replacement Image Display Box:
Image Crosshair
To change the image crosshair:
Image Color Map
To change the image color map:
Camera Crosshair
4.4.2 Using Tools for Pixel Replacement
Zoom
To use zoom:
Arrow Buttons/Navigation
4.4.3 Replacing Pixels
Replacement Code
To use replacement code:
Replace Row
To replace a row of pixels:
Replace Column
To replace a column of pixels:
Undo Replacement
If the wrong pixel was replaced, the replacement can be undone.
To undo a pixel replacement:
4.4.4 Import List
4.4.5 Finish
5 Troubleshooting
Index
Pearl Control So
ftware Manua
l
Intr
oduction
14
To en
s
u
re consi
stent document formatti
ng, this page was in
tention
ally left blank.
1
...
...
12
13
14
15
16
...
...
44
