Instructions / Assembly

ManualsBrandsLumark ManualsLightingCrosstour 120-Watt Equivalent Outdoor Integrated LED, Carbon Bronze Wall Pack Light, 4000K with Refractive Lens

INS #

Brand Logo

reversed out of

black

INS #

IB514001EN

Installation Instructions - Crosstour MAXX

Instructions d’installation - Crosstour MAXX

Instrucciones de instalación - Crosstour MAXX

WARNING

Make certain power is OFF before starting installation

or attempting any maintenance. Risk of ﬁre/electric

shock. If not qualiﬁed, consult an electrician.

WARNING

Make certain power is OFF before starting installation

or attempting any maintenance.

WARNING

Risk of Electric Shock—Disconnect power at fuse or

circuit breaker before installing or servicing.

WARNING

Risk of Burn—Disconnect power and allow fixture to

cool before servicing.

WARNING

Risk of Personal Injury— DO NOT mount luminaire

within 6” of a combustible surface. DO NOT handle

luminaire by the lens.

WARNING

Risk of Personal Injury— Fixture may become

damaged and/or unstable if not installed properly.

Tighten all fixture components to their

recommended torque values. Do not lift pole into

place by securing lifting device to lighting fixture or

mounting arm.

ote:N These instructions do not claim to cover all

details or variations in the equipment, procedure,

or process described, nor to provide directions

for meeting every possible contingency during

installation, operation or maintenance. When

additional information is desired to satisfy a

problem not covered sufficiently for user’s purpose,

please contact your nearest representative.

Specifications and dimensions subject to change

without notice.

IMPORTANT: Read before installing ﬁxture. Retain for future reference.

SAFETY: This ﬁxture must be wired in accordance with the National Electrical Code and applicable local codes and

ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under

installation section.

TOOLS REQUIRED: Phillips head screwdriver, electrical wiring tools, drill, 9/32” drill bit, tape measure.

MATERIAL NOT INCLUDED: Wall anchors, washers, mounting bolts, silicone sealant, liquid tight conduit, and wire nuts.

APPLICATION: Crosstour MAXX LED luminaires are designed for outdoor, wet location use not to exceed 40°C ambient

(50°C ambient for HA models). Approved for wall/surface applications in down light or uplight (invert) mount. For

thru-branch wiring utilize 4-12 AWG, 90°C wire.

Summary of content (16 pages)

PAGE 1
Brand Logo reversed out of black IB514001EN INS # Installation Instructions - Crosstour MAXX Instructions d’installation - Crosstour MAXX Instrucciones de instalación - Crosstour MAXX WARNING Make certain power is OFF before starting installation or attempting any maintenance. Risk of fire/electric shock. If not qualified, consult an electrician. WARNING Make certain power is OFF before starting installation or attempting any maintenance.
PAGE 2
Installation Instructions - Crosstour MAXX INSTALLATION Wall Gasket BACK BOX INSTALLATION 1. Unscrew door with Phillips screw driver. Remove door from back box. 2. Place inverted back box on solid surface. Using a 9/32” bit, drill out the four mounting holes. (Figure 1.) 3. ver Junction Box Wiring And Rear Entry Conduit O Installation: Loosen But DO NOT remove two screws securing wire-way cover plate (Figure 2).
PAGE 3
Installation Instructions - Crosstour MAXX DOOR INSTALLATION 6. Ensure all electrical wires and connections are secured in the back box, re-install door and tighten door screw to 15-20 in-lbs. MAINTENANCE NNote: A regular maintenance schedule should be followed to retain optimal light output and thermal performance. Optical lens cleaning should be performed with a clean dry cloth to remove any dust or other contaminants. Additional lens cleaning should be performed with non-abrasive acrylic cleanser.
PAGE 4
Installation Instructions - Crosstour MAXX With Photocontrol Driver Load (Black) Factory Wired Driver to LED Neutral (White) Supply Neutral (White) Load (Red) Neutral (White) Supply Line (Black) Line (Black) Photocontrol 347V/480V Without Photocontrol Driver Factory Wired Driver to LED Line (Black) Neutral (White) Supply Neutral (White) Connect Supply Line Here for 347V Application Load (Red) XFMR Neutral (White) 347V (Black) Supply Line (Black) 480V (Yellow) Connect Supply Line Here for 48
PAGE 5
Installation Instructions - Crosstour MAXX 347V/480V With Photocontrol Driver Factory Wired Driver to LED Line (Black) Neutral (White) Supply Neutral (White) Load (Red) Neutral (White) Photocontrol Line (Black) Load Red XFMR Connect Supply Line Here for 347V Application Neutral 347V (White) (Black) 480V (Yellow) Supply Line (Black) Connect Supply Line Here for 480V Application COOPER LIGHTING SOLUTIONS IB514001EN Installation instructions 5
PAGE 6
Instructions d’installation - Crosstour MAXX AVERTISSEMENT AVERTISSEMENT Assurez-vous que l'alimentation électrique est HORS TENSION avant de commencer l'installation ou de procéder à l'entretien. Risque d’incendie ou de décharge électrique. Si vous n’êtes pas qualifié, consultez un électricien. AVERTISSEMENT Assurez-vous que l'alimentation électrique est HORS TENSION avant de commencer l'installation ou de procéder à l'entretien.
PAGE 7
Instructions d’installation - Crosstour MAXX INSTALLATION Joint mural INSTALLATION DU BOÎTIER ARRIÈRE Dévissez le couvercle avec le tournevis cruciforme. Retirez le couvercle du boîtier arrière. 2. Placez le boîtier arrière à l'envers sur une surface solide. Percez les quatre trous de fixation avec le foret de 7 mm (9/32 po). (Figure 1.) 3.
PAGE 8
Instructions d’installation - Crosstour MAXX ntrée arrière du conduit: Enlevez l’œillet noir et les E fils de la plaque protectrice de la goulotte (NE RETIREZ PAS le joint circulaire). Attachez le conduit à la plaque protectrice de la goulotte à l'aide du serre-fil étanche. Remettez la plaque protectrice sur les vis en la tournant dans le sens des aiguilles d'une montre. Serrez les vis de la plaque protectrice de la goulotte selon un couple de 1,12 Nm (10 po/lb) (Figure 2).
PAGE 9
Instructions d’installation - Crosstour MAXX Avec Photocontrôle Module Charge (noir) Module câblé en usine vers la DEL Neutre (blanc) Fil neutre (blanc) Charge (rouge) Neutre (blanc) Photocontrôle Fil d'alimentation (noir) Ligne (noir) Sans Photocontrôle 347V/480V Module Module câblé en usine vers la DEL Fil (noir) Neutre (blanc) Fil neutre (blanc) Branchez le fil d'alimentation ici pour utilisation à 347 V Charge (rouge) XFMR Neutre (blanc) 347V (noir) Fil d'alimentation (noir) 480V (jaune
PAGE 10
Instructions d’installation - Crosstour MAXX Avec Photocontrôle 347V/480V Module Module câblé en usine vers la DEL Fil (noir) Neutre (blanc) Fil neutre (blanc) Charge (rouge) Neutre (blanc) Photocontrôle Ligne (noir) Charge rouge XFMR Branchez le fil d'alimentation ici pour utilisation à 347 V Neutre (blanc) 480V (jaune) 347V (noir) Fil d'alimentation (noir) Branchez le fil d'alimentation ici pour utilisation à 480 V 10 COOPER LIGHTING SOLUTIONS IB514001EN Instructions d’installation
PAGE 11
Instrucciones de instalación - Crosstour MAXX ADVERTENCIA ADVERTENCIA Asegúrese de que la alimentación esté DESCONECTADA antes de comenzar la instalación o intentar realizar el mantenimiento. Riesgo de incendio y descarga eléctrica. Si no está calificado, consulte a un electricista. Riesgo de lesiones personales: NO monte la luminaria dentro de 6” (15,24 cm) de una superficie inflamable. NO manipule la luminaria tomándola del lente.
PAGE 12
Instrucciones de instalación - Crosstour MAXX INSTALACIÓN Junta de pared INSTALACIÓN EN CAJA TRASERA Desatornille la puerta con el destornillador Phillips. Retire la puerta de la caja trasera. 2. Coloque la caja trasera invertida sobre una superficie sólida. Con una broca de 9/32”, taladre los cuatro orificios de montaje. (Figura 1.) 3.
PAGE 13
Instrucciones de instalación - Crosstour MAXX ntrada al conducto trasero: retire el aislante negro E y los cables de la placa de cubierta para cables (NO retire la junta circular). Una el conducto con la placa de cubierta para cables usando un conector hermético. Reinstale la placa de cubierta para cables girándola en sentido horario. Ajuste los tornillos de placa de cubierta para cables hasta 10 pulg.-lb (Figura 2). 5.
PAGE 14
Instrucciones de instalación - Crosstour MAXX Con Fotocontrol Conductor Carga (negro) Controlador conectado en fábrica al LED Neutro (Blanco) Carga (Rojo) Neutro de alimentación (Blanco) Neutro (Blanco) Cable de línea (negro) Línea (negro) Fotocontrol 347V/480V Sin Fotocontrol Conductor Controlador conectado en fábrica al LED Línea (negro) Carga (Rojo) XFMR Neutro (Blanco) Neutro de alimentación (Blanco) Neutro (Blanco) 480 V (Amarillo) 14 COOPER LIGHTING SOLUTIONS IB514001EN Instrucciones
PAGE 15
Instrucciones de instalación - Crosstour MAXX 347V/480V Con Fotocontrol Conductor Controlador conectado en fábrica al LED Línea (negro) Neutro (Blanco) Neutro de alimentación (Blanco) Carga (Rojo) Neutro (Blanco) Fotocontrol Carga (Rojo) XFMR Conecte aquí la línea de alimentación para una aplicación de 347V Línea (negro) Neutro 347V (Blanco) (Negro) 480V (Amarillo) Cable de línea (negro) Conecte aquí la línea de alimentación para una aplicación de 480V COOPER LIGHTING SOLUTIONS IB514001EN Ins
PAGE 16
Warranties and Limitation of Liability Please refer to www.cooperlighting.com for our terms and conditions. Garanties et limitation de responsabilité Veuillez consulter le site www.cooperlighting.com pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.cooperlighting.com para conocer nuestros términos y condiciones. Cooper Lighting Solutions 1121 Highway 74 South Peachtree City, GA 30269 P: 770-486-4800 www.cooperlighting.