Installation Guide

ManualsBrandsLumark ManualsLightingCrosstour 120-Watt Equivalent Outdoor Integrated LED, Carbon Bronze Wall Pack Light, 5000K Photocontrol

INS #

Brand Logo

reversed out of

black

INS #

IB514015EN

Installation Instructions - Crosstour LED

Instructions d’installation - Crosstour DEL

Instrucciones de instalación - LED Crosstour

IMPORTANT: Read before installing ﬁxture. Retain for future reference.

SAFETY: This ﬁxture must be wired in accordance with the National Electrical Code and applicable local codes and

ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under

installation section.

APPLICATIONS: Crosstour luminaires are designed for outdoor, wet location use not to exceed 40°C ambient (50°C

models available). Approved for wall/surface, post/bollard, inverted mount or ground mount applications. For thru-branch

wiring utilize 4-12 AWG, 90°C wire.

WARNING

Make certain power is OFF before starting installation

or attempting any maintenance. Risk of fire/electric

shock. If not qualified, consult an electrician.

WARNING

RISK OF ELECTRIC SHOCK—Disconnect power at fuse

or circuit breaker before installing or servicing.

WARNING

RISK OF BURN—Disconnect power and allow fixture

to cool before servicing.

WARNING

RISK OF PERSONAL INJURY—Fixture may become

damaged and/or unstable if not installed properly.

WARNING

DO NOT handle luminaire by the glass.

WARNING

Make certain power is OFF before starting installation

or attempting any maintenance.

ote:N These instructions do not claim to cover all

details or variations in the equipment, procedure,

or process described, nor to provide directions

for meeting every possible contingency during

installation, operation or maintenance. When

additional information is desired to satisfy a

problem not covered sufficiently for user’s purpose,

please contact your nearest representative.

ote:N Specifications and dimensions subject to change

without notice.

Summary of content (13 pages)

PAGE 1
Brand Logo reversed out of black IB514015EN INS # Installation Instructions - Crosstour LED Instructions d’installation - Crosstour DEL Instrucciones de instalación - LED Crosstour WARNING Make certain power is OFF before starting installation or attempting any maintenance. Risk of fire/electric shock. If not qualified, consult an electrician. WARNING RISK OF ELECTRIC SHOCK—Disconnect power at fuse or circuit breaker before installing or servicing.
PAGE 2
Installation Instructions - Crosstour LED INSTALLATION NNote: Available on 7W, 18W, 26W and 38W models only. Tools Required Phillips head screw driver and electrical wiring tools. 1. Unscrew door with phillips screw driver. Remove door from back box. Confirm junction box size prior to removing the gasket material for the application (Figure 1). Only remove the gasket material needed for the installation. Mount back box to junction box via supplied hardware or lag mount.
PAGE 3
Installation Instructions - Crosstour LED Crosstour without Photocontrol AC Input Load (Black) Neutral (White) LED Driver Supply Neutral (White) DC Output Supply Line (Black) Supply Ground Back Box Ground Front Housing Ground Connect all Ground Wires First Factory Wired LED to Driver Crosstour with Photocontrol AC Input Load (Black) Load (Red) Neutral (White) Neutral (White) LED Driver Factory Wired LED to Driver Line (Black) Supply Line (Black) Wire Nut Supplied by Others DC Output
PAGE 4
Installation Instructions - Crosstour LED Figure 4. 4 COOPER LIGHTING SOLUTIONS Figure 5.
PAGE 5
Instructions d’installation - Crosstour DEL AVERTISSEMENT AVERTISSEMENT Assurez-vous que l'alimentation électrique est HORS TENSION avant de commencer l'installation ou de procéder à l'entretien. Risque d’incendie ou de décharge électrique. Si vous n’êtes pas qualifié, consultez un électricien. AVERTISSEMENT RISQUE DE DÉCHARGE ÉLECTRIQUE—Mettez la source d’alimentation hors tension en enlevant le fusible ou en déclenchant le disjoncteur avant l’installation ou l’entretien.
PAGE 6
Instructions d’installation - Crosstour DEL RRemarque: L’installateur doit appliquer du joint en silicone tout autour du boîtier arrière, sur la zone correspondant à la surface d’installation. Il y aura alors une étanchéité entre la surface d'installation et le boîtier arrière (Figure 6.). 2. Fixez la porte dans les charnières de blocage situées sur le dessus du boîtier arrière (pour un éclairage vers le bas) (Figure 2).
PAGE 7
Instructions d’installation - Crosstour DEL Crosstour sans photocontrôle Connectez d’abord tous les fils de mise à la terre Pilote de DEL Entrée CA Boîtier de masse avant Mise à la terre du boîtier arrière Mise à la terre d'alimentation Charge (Noir) Neutre (Blanc) Fil neutre (Blanc) Sortie CC Fil d'alimentation (Noir) DEL vers commande câblé en usine Crosstour avec photocontrôle Neutre (Blanc) Neutre (Blanc) Pilote de DEL DEL vers commande câblé en usine Fil (Noir) Fil d'alimentation (Noir)
PAGE 8
Instructions d’installation - Crosstour DEL Figure 5. Figure 4.
PAGE 9
Instrucciones de instalación - LED Crosstour ADVERTENCIA ADVERTENCIA Asegúrese de que el suministro eléctrico esté DESCONECTADO antes de iniciar la instalación o de intentar hacer cualquier reparación. Riesgo de incendio o descarga eléctrica. Si no está calificado, consulte con un electricista. ADVERTENCIA RIESGO DE DESCARGA ELÉCTRICA—Desconecte la alimentación en el disyuntor o fusible antes de instalar o realizar tareas de mantenimiento.
PAGE 10
Instrucciones de instalación - LED Crosstour NNota: El instalador debe aplicar compuesto de silicona alrededor de todo el perímetro de la caja trasera donde se une a la superficie de montaje. Esto creará un sello hermético entre la superficie de montaje y la caja trasera (Figura 5). 2. Asegure la puerta en las bisagras de sujeción ubicadas en la parte superior de la caja trasera (para iluminación focal descendente) (Figura 2).
PAGE 11
Instrucciones de instalación - LED Crosstour Luminaria Crosstour sin fotocontrol Carga (Negro) Neutro (Blanco) Controlador LED Neutro de suministro (Blanco) Salida de CC Entrada de CA Línea de suministro (Negro) Conexión a tierra de la alimentación Conexión a tierra en caja trasera Frente Conexión a tierra del alojamiento Primero conecte todos los cables a tierra Cableado de fábrica LED a controlador Luminaria Crosstour con fotocontrol Entrada de CA Carga (Negro) Carga (Rojo) Neutro (Blanco
PAGE 12
Instrucciones de instalación - LED Crosstour Figura 4. 12 COOPER LIGHTING SOLUTIONS IB514015EN Figura 5.
PAGE 13
Warranties and Limitation of Liability Please refer to www.cooperlighting.com for our terms and conditions. Garanties et limitation de responsabilité Veuillez consulter le site www.cooperlighting.com pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.cooperlighting.com para conocer nuestros términos y condiciones. Cooper Lighting Solutions 1121 Highway 74 South Peachtree City, GA 30269 P: 770-486-4800 www.cooperlighting.