Instructions / Assembly

ManualsBrandsLumark ManualsLightingWP Series 100-Watt Equivalent Integrated LED Bronze Outdoor Small Wall Pack Light, 4,733 Lumens, 4000K Bright White

INS #

Brand Logo

reversed out of

black

INS #

IB514012EN

Installation Instructions - WPSLED

Instructions d’installation - WPSLED

Instrucciones de instalación - WPSLED

IMPORTANT: Read before installing ﬁxture. Retain for future reference.

SAFETY: This ﬁxture must be wired in accordance with the National Electrical Code and applicable local codes and

ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under

installation section.

WARNING

Make certain power is OFF before starting installation

or attempting any maintenance. Risk of fire/electric

shock. If not qualified, consult an electrician.

WARNING

Risk of Electric Shock—Disconnect power at fuse or

circuit breaker before installing or servicing.

WARNING

Risk of Burn—Disconnect power and allow fixture to

cool before servicing.

WARNING

Risk of Personal Injury—Fixture may become damaged

and/or unstable if not installed properly.

WARNING

DO NOT mount luminaire within 6” of a combustible

surface. DO NOT handle luminaire by the glass.

ote:N These instructions do not claim to cover all

details or variations in the equipment, procedure,

or process described, nor to provide directions

for meeting every possible contingency during

installation, operation or maintenance. When

additional information is desired to satisfy a

problem not covered sufficiently for user’s purpose,

please contact your nearest representative.

ote:N Specifications and dimensions subject to change

without notice.

Summary of content (8 pages)

PAGE 1
Brand Logo reversed out of black IB514012EN INS # Installation Instructions - WPSLED Instructions d’installation - WPSLED Instrucciones de instalación - WPSLED WARNING Make certain power is OFF before starting installation or attempting any maintenance. Risk of fire/electric shock. If not qualified, consult an electrician. WARNING Risk of Electric Shock—Disconnect power at fuse or circuit breaker before installing or servicing.
PAGE 2
Installation Instructions - WPSLED INSTALLATION Wire Connector Applications These luminaires are designed for outdoor, wet location services and should not be used in areas with limited ventilation or in high ambient temperature enclosures. The luminaire shall be wall mount only. Inverted mounting will cause overheating and possible water entry. Tools Required Philips screwdriver, Torx T-20 bit (included), 6mm multi-bit screw driver or 6mm socket, 1/4” drill bit. 1.
PAGE 3
Installation Instructions - WPSLED Wire Guard Installation Retainer Content 1 Wire Guard, 4 Screws, 4 Washers. 1. Open the glass door of fixture, screw-off and save the retainer. 2. Install the wire guard, use enclosed 4 new “longer” screws (replace the original 4 screws) and twist the retainer back, according to (Figure 3.) Figure 3.
PAGE 4
Instructions d’installation - WPSLED AVERTISSEMENT Assurez-vous que l'alimentation électrique est HORS TENSION avant de commencer l'installation ou de procéder à l'entretien. Risque d’incendie ou de décharge électrique. Si vous n’êtes pas qualifié, consultez un électricien. AVERTISSEMENT Risque de décharge électrique - Débranchez la source d'alimentation en enlevant le fusible ou en déclenchant le disjoncteur avant l'installation ou l'entretien.
PAGE 5
Instructions d’installation - WPSLED 4. Utilisez des connecteurs homologués pour connecter les fils du luminaire aux fils d'alimentation et repoussez les épissures dans la boîte de jonction. 5. Montez la plaque de montage à l'aide des vis sur la surface du boîtier encastré. Installez le joint auto-adhésif fourni à l'arrière du luminaire afin de couvrir la plaque de montage. Assurez-vous de calfeutrer entre la plaque de montage et le boîtier pour assurer une bonne étanchéité. 6.
PAGE 6
Instrucciones de instalación - WPSLED ADVERTENCIA Asegúrese de que el suministro eléctrico esté DESCONECTADO antes de iniciar la instalación o de intentar hacer cualquier reparación. Riesgo de incendio o descarga eléctrica. Si no está calificado, consulte con un electricista. ADVERTENCIA Riesgo de descarga eléctrica - desconecte la alimentación en el disyuntor o fusible antes de instalar o realizar tareas de mantenimiento.
PAGE 7
Instrucciones de instalación - WPSLED 4. Use los conectores aprobados para unir los conectores de la luminaria con los conectores de alimentación y realice empalmes de cables dentro de la caja de derivación. 5. Instale la placa de montaje con tornillos sobre la caja de superficie empotrada. Instale la junta autoadhesiva incluida en la parte trasera de la luminaria para cubrir la placa de montaje.
PAGE 8
Warranties and Limitation of Liability Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions. Garanties et limitation de responsabilité Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones. Eaton 1121 Highway 74 South Peachtree City, GA 30269 P: 770-486-4800 www.eaton.